Mains
chief conduit of electricity, gas or water distribution.
-
Product
DAQ Modules
Q.series X DAQ Modules for EtherCAT
-
All Q.series X DAQ systems possess the same measurement capabilities and performance. The main differentiating factor between the XL and XE versions of Q.series X is the Fieldbus communication protocol, which can be interchanged on Q.series X modules using a simple firmware update.
-
Product
SIGNAL & POWER ISOLATOR
EE301-ISOL
-
The EE301-ISOLATOR will completely isolate your electronic loads inputs & outputs signals plus ground returns from the main power input UUT (unit under test)... The module allows you to control the electronic load just as you would with any standard control signal. Input / Output & Power signals are fully isolated up to 350 VDC.
-
Product
Audio Frequency Transmitter
TG 20/50
-
Cable fault location with the BAUR TG 20/50. The TG 20/50 is a portable, battery-operated audio generator with a built-in charging unit. Together with the UL audio frequency receiver and the SP detecting rod, the TG 20/50 is used for cable tracing, twist method and for determining the depth of cables and metal pipes.* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output* Two output frequencies selectable
-
-
Product
Full-Size Loudspeakers
UPQ
-
Meyer Sound’s award-winning UPQ loudspeakers have been core components in both portable and installed systems for more than a decade. Characterized by a high power-to-size ratio; smooth, uniform coverage; and consistent polar response; these two-way, self-powered loudspeakers are available in three coverage patterns to fit any application, from FOH mains in small-to-midscale systems to fills in large systems.
-
Product
10A Continuity Tester
EQUITEST
-
EQUITEST is connected to its master unit via C2050 cable and to the mains for power supplying.Please refer to the user manual of your HT installation safety tester for the compatibility to EQUITEST.
-
Product
E/O Converter
LTX-510
-
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
-
Product
I-8000W High Performance Modules
-
The I-8000 High Performance Modules are for use with ViewPAC, WinPAC, XPAC and LinPAC controllers. There are two types of I/O modules, Parallel and Serial. The parallel modules (I-8K Series) are high-speed modules and support MCU (Main Control Unit) only.
-
Product
Programmer AUTO300 Weilei Memory
-
AUTO300 is the newest programmer from weilei company. That programmer is dedicated to automotive electronics. The main advantages are : reliability, speed, and the ratio of quality to price, the software in ten languages and 3-year warranty
-
Product
Harmonic Trap Inductors
-
Osborne designs harmonic trap inductors to work in conjunction with capacitors in power systems to prevent specific line-frequency harmonics from flowing back to the power source (point of common connection). This power quality design approach prevents harmonic currents from flowing to the main facility power system and/or to the utility power system. The Osborne system also reduces unnecessary power losses and power-system pollution.
-
Product
Copy Tools
DemiXG1020
-
Main unit weight is approx. 1.4kg, ultra compact and thin designResults in superior portability, perfect for on-site copying, backup, and data deletion.High speed data transfer at 10GB per minute (*1).(*1 Transfer speed varies according to performance of connected devices.)Reverse copy functionCan copy from last portion of HDD. Perfect for restoring data.Built-in evidence preservation functions including hash generation (MD5, SHA1, and SHA256) and creating DD images, etc.Built-in deletion function and quick diagnosis functionDeletion report can be created using host software (sold separately).
-
Product
Wide Range TMAH Concentration Monitor
HE-960H-TM
-
Accurately measures the concentration of TMAH (Tetra Methyl Ammonium Hydroxide), which is the main component of the photoresist developer solutions in semiconductor manufacturing. Wide measurement range : 0 - 10 %. Have the chemical resistant carbon sensor.
-
Product
Oscilloscope DIY Kit
DSO 138
-
DSO138 was designed as a training oscilloscope kit. It contains only the basic oscilloscope functions with no fancy features. Simplicity in structure and easiness in assembly/operation are amongst the main highlights of the design. For these purposes, DSO138 uses mostly through-hole parts. The heart of DSO138 is a Cortex-M3 ARM processor (STM32F103C8) from ST. It uses a 2.4-inch TFT LCD (320 X 240 dotmatrix, 262K colors) that displays crisp and clear waveforms.
-
Product
PXIe-8830MC, Intel Core i7 Processor PXI MultiComputing Processing Module
783564-33
Processing Module
The PXIe‑8830mc allows two or more intelligent systems to exchange data using PCI Express technology. Featuring an Intel quad-core processor, the NI PXIe‑8830mc can be installed in any PXI Express peripheral slot. It runs on the LabVIEW Real‑Time OS and can act as a coprocessor to offload the processing from the main embedded controller in the system.
-
Product
Vertical Space Transformers
ST
-
The Space Transformer (ST) is an integral part of the probe card, utilized between the probe head and the PCB. Nidec SV Probe provides a wide variety of space transformation options including: • WST™ (Wired Space Transformer) • MST™ (Modular Space Transformer) • MLC (Multi-Layer Ceramic) • MLO/Mini-PCB (Multi-Layered Organic) • Multi-Site MLO Reflow of Package Substrate • MLC with MLTF to 50µm PitchOne of the main priorities for Nidec SV Probe is the internal development and manufacture of our own probe card components. We now offer in-house manufactured space transformer technologies with shorter lead time and competitive pricing. Contact your sales representative to learn more about our internally manufactured STs or any of our other ST technologies.
-
Product
Modular Type SELEX FRL Regulator Mounting Dedicated Digital Pressure Sensor
PPR
-
This is a digital pressure sensor dedicated to mounting a modular type regulator.Displayed values and set values can be checked at the same time on a 2-screen display.You can check the displayed value (current value) on the main display and the set value on the sub display.
-
Product
Advanced Industrial Multimeter
CMM-60
-
The CMM-60 multimeter allows you to record data thanks to the Trend Capture function of the built-in memory as well as the possibility of transferring data and analysing the results achieved in the CMM-60 Multimeter Software. The device facilitates the diagnostics of potential problems covering the operation of electromechanical devices, industrial automation, motors and distribution of electricity. Precise indications, safety during work in industrial conditions, convenience of use and early detection of irregularities in the operation of machines and devices are the main benefits of having this device in your equipment.
-
Product
Manual PAT Testers
-
If you are looking for a manual PAT tester with a pass fail reading or a PAT tester with readings we have a solution for you. Carry out mains supply checks, IEC lead tests, Earth continuity tests at 200mA, Insulation resistance tests to 250V and 500V, and more with these popular testers. All of our manual PAT testers are available as kits to help you streamline the way you work.
-
Product
Linear DC Power Supply
-
A device that takes AC current (mains or line current, depending upon where in the world you are) and converts it into safe low-voltage DC at the desired voltage level.
-
Product
MIL-STD-1553 Modules
-
> MIL-STD-1553B is the military specification defining a digital time division command/response multiplexed databus. The 1553 databus is a dual-redundant, bi-directional, Manchester II encoded databus with a high bit error reliability. All bus communications are controlled and initiated by a main bus controller. Remote terminal devices attached to the bus respond to controller commands. MIL-STD-1553B defines specifications for terminal device operation and coupling, word structure and format, messaging protocol and electrical characteristics.
-
Product
Open Loop Current Sensor
C03 30A
-
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in industrial, commercial and communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
Product
Hydrogen Frequency & Time Standard
CH1-1007
-
Hydrogen frequency and time standard Ch1-1007 is designed to generate and reproduce precision, highly stable, spectrally pure frequency and time signals. Main areas of application: – in metrology when transferring the sizes of units of frequency and time, including as part of mobile measuring complexes; – in radio astronomy when conducting scientific research; - in radio navigation when working as part of automated measuring systems and complexes.
-
Product
Universal Transmitter
Model LXT-330
-
Teledyne Analytical Instruments
Model LXT330 Liquid Transmitter is a single or dual channel, universal, multi-parameter transmitter, designed for continuous online liquid measurements. It is paired with SP3 Smart sensors and is intended for use in non-hazardous, general purpose rated industrial environments. The SP3 sensor platform covers a wide range of liquid analytical measurements, such as pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity, resistivity and turbidity. The LXT330 transmitter can be used with any SP3 smart sensors without additional user reconfiguration. The Universal Transmitter & Smart Sensor loop philosophy removed the need to stock for multiple instrument types. The process parameter, sensor details, serial number and calibration history are stored in the sensor's main memory, facilitated by two-way digital communication between the sensors and transmitter. The LXT330 universal transmitter allows for up to two SP3 sensors per transmitter (contact factory for available combinations).
-
Product
Radiating Loops
-
The magnetic, handheld coil was designed to generate defined mag-netic fieldstrength in the frequency range from DC up to 5 (7) MHz. The main application is immunity testing against magnetic fields.
-
Product
Breakout Box and Data Logger
1U643-001
-
The 1U634 Breakout Box and Data Logger was developed for the Cessna Excel to serve as the main diagnostics tool for the aircraft?? electronic modules. It allows access to the module pins, and its internal microcomputer digitizes the signals and transmits them to a PC-compatible computer. Advanced software in the computer displays pin voltages either in numerical or graphical form. Data files can be recorded on disk, and played back at a later time for detailed analysis.
-
Product
Industrial Communication
-
Reliable data flow and transparent communication across all production processes have become indispensable in automation. The main goal of industrial communication is to integrate all plant areas from the control to the field level in a networked system. Because consistent and powerful data networks increase the availability and efficiency of machines and systems.
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
Matrix Switch Module
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
Products for High-Frequency Measurement
-
This product range includes passive high-frequency test probes and accessories as well as touch-protected BNC plug connectors, insulated BNC panel-mount sockets, leads with RG58 or RG59 cable, adapters and converters. Our test probes are suitable for use in CAT III- and CAT IV environments (Measurement Categories), such as the analysis of house and building installations with mains analysis/mains monitoring devices. Our high-frequency accessories are designed with clearance and creepage distances in accordance with IEC/EN 61010-031.
-
Product
Reactive Energy Regulator
MASTER
-
Lifasa - International Capacitors, SA
It measures the reactive power needs of an installation and gives the corresponding capacitor connection and disconnection orders to keep the cos φ preset. At the same time it allows to measure the main parameters of an installation (voltage, current, harmonics, active power, reactive power, etc.), by using 1 or 3 current measurement transformers.
-
Product
Single Sheet Tester
Model SST500X500
-
Gopal Make single sheet tester SST is developed as per IEC 60404-3. It can be attached as probe to Ep400 Main unit and user can test specific total loss, specific apparent power, and r.m.s value of magnetic field strength as well as B/h curve in the software.
