Programmable Switching Power Supplies
-
Product
Power, Patchcord, Receiver, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps)
7-252414000-036
-
Power, Patchcord, Receiver, 36", Micro Power, 14 AWG Twisted Pair, Single Ended (22 Amps).
-
Product
PXI 4 Slot BRIC Matrix, Solid State, 128x8, 1-Pole (4 sub-cards)
40-563B-021-128X8
-
The 40-563B-021-128x8 is an ultra high density 4-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-012
-
The 40-254-012 (PXI) and 42-254-012 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 120Ω with 0.5Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm - SPST
40-294-124
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
SIMRC - 8 x 4 Matrix 2-Pole
1030-R-8-4-2-5/1D
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 122Ω
40-252-112
-
The 40-252-112 is a programmable resistor module with 2 channels which can be set between 1Ω and 122Ω with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
PXI 8-Slot BRIC Matrix, 176x4 2-Pole (4 sub-cards)
40-562B-122-176X4
-
The 40-562B-122-176X4 is a high density BRIC8 matrix module with a size of 176x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 55x32 1-Pole (11 sub-cards)
40-562A-121-55X32
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 18 GHz, 50 Ω, SMA, Failsafe
42-782B-521
-
The 40-782B-521 (PXI) and 42-782B-521 (PXIe) single failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
120W Power Supply, 15V, 7A or 30V, 4A
E3632A
-
Keysight basic DC power supplies offer essential features for a tight budget. The single output, 120-200 W, GPIB, E3632A-E3634A provide dual range outputs; small, compact size for bench use; low output ripple and noise; as well as built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 120W, GPIB, single output E3632A is a high performance supply optimized for manual and basic automated testing; and, with a combination of benchtop capabilities and system features, it is designed to help improve measurement quality and reduce test time.
-
Product
PXI 8 Slot BRIC 88x16 1-Pole (8 sub-cards)
40-562A-121-88X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-121-230X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4-Slot BRIC Matrix, 15x32 1-Pole (3 Sub-cards)
40-562B-021-15X32
-
The 40-562B-021-15X32 is a high density BRIC4 matrix module with a size of 15x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
8-Slot BRIC, 84x12, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-801-84x12
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps)
7-222902000-036
-
Power, Patchcord, ITA, 36", High Power, 2 AWG, Single Ended (150 Amps).
-
Product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
-
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
Product
PXI 12-Slot BRIC Matrix, 64x16 1-Pole (2 sub-cards)
40-558-121-64X16
-
The 40-558-121-64x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe RF Matrix, 16x4, 300 MHz, 50 Ω MS-M Multiway With Loop-thru
40-727A-002-L
-
The 40-727A-002-L (PXI) and 42-727A-002-L (PXIe) are 16x4 50 Ω RF matrices with MS-M Multiway connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI 12-Slot BRIC Matrix, 448x16 1-Pole (14 sub-cards)
40-558-121-448X16
-
The 40-558-121-448x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI Dual 2x2 Insert/Bypass Switch ST
40-860-522-M
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI High Density Matrix Module, 16x16, 2-Pole, 2A
40-582A-001
-
The 40-582A is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 16x16 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 132x8, 3 Sub-cards
40-567A-103
-
The 40-567A-103 is a PXI 1-pole 132x8 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 100VDC/70VAC. The 40-567A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 8 Slot BRIC 150x8 1-Pole (5 sub cards)
40-561A-121-150X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-011
-
The 40-254-011 (PXI) and 42-254-011 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 61Ω with 0.25Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI Ultra High Density 64x2 1-Pole Matrix
40-533B-031
-
The 40-533B ultra high density matrix module is configured as 64x4 or 64x2 and is available in a choice of 1-pole and 2-pole reed relay formats. Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
LXI High Density 384x4 Matrix - 60-551-026
60-551-026
-
High-density single pole matrix module capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXIe Flexible Microwave Module, Dual SP4T Terminated 40 GHz, Single SPDT 40 GHz, 50 Ω, SMA
42-890-002
-
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
Product
PXI Source Switching Module
40-618A-001
-
The 40-618A PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module.
-
Product
(8×32)-Ch 0,5A-200VAC Matrix
YAV90062
-
256 relays SPST matrix (4×64 1 pole) or (4×32 2 poles). Max switching 10W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
PXI 8 Slot BRIC 58x6 2A 1-Pole Matrix
40-596-101
-
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.





























