Network Load
-
Product
Three Phase Manual Coupling/Decoupling Networks
CDN 3083 Series
-
Three phase 440 VAC/DC and 620 VAC/DC 100 and 200 A manual coupling/decoupling networks (CDNs) for Surge.
-
Product
Compression Load Cells
-
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
Product
Multi-channel DC Electronic Load
IT8700 Series
-
IT8700 series programmable DC electronic load adopts removable modules design, supports up to 16 channels with mainframe extension transient mode up to 25 kHz, which improves your test efficiency, with high resolution and accuracy. Users can freely choose in the 8 load modules according to the number of channels and power requirements, controlled by mainframe control panel, or controlled by host computer software via built-in LAN / RS232 /USB / GPIB interface.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Network Traffic Generator
LANforge FIRE
-
LANforge FIRE generates network traffic at various speeds with the ability to monitor packets for throughput and correctness. LANforge FIRE sits on the edge of your network and tests your network core. Useful for testing any network, and especially cost effective for efforts requiring many data-generating ports, such as DSL, Cable-Modem, and Satellite modems.
-
Product
Variable Resistor Load Bank
REOLOAD 100
-
A variable resistor load-bank with fixed stages connected in parallel and switched in, as required, with an adjustable stage for fine trimming. Designed for testing equipment under load. 1000V (AC or DC). 250A and 2500
-
Product
Length Network Cable Tester
SC-8108
-
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
Product
VME / VME64x Load Board 6U
1940000140-0000
-
The Elma Electronic VME / VME64x load board provides a means to test the power generated by and cooling capability of VME systems. This makes it easier to locate hot spots in the chassis, so the airflow can be properly directed.
-
-
Product
Network Centric Telemetry Processing
C2TM Gateway
-
Command and Control Technologies Inc.
The C²TM Gateway is uniquely engineered to enable decision-focused situation awareness with unparalleled configuration flexibility, timely information processing and visualization, and robust interoperability. The C²TM Gateway can deliver your mission critical telemetry data synchronized, fused, and in context, to wherever you do business.
-
Product
Controllable, Programmable Linear DC Source With Load
LAB / SL
-
*Linear laboratory power supply*Integrated electronic load*Linear regulated DC laboratory power supply*No thyristor pre-regulation, very little ripple*Various interfaces · Built-in electronic load*Protection against short circuit, overload and overtemperature*Constant current and constant voltage*Fast control times approx. 250 µS
-
Product
Network Simulation and Load Testing
-
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
Product
Programable Power Supply & Programable Electronic Load
EL-820P
-
*Digital button control and easy operation*High resolution(20mV, 10mA, 0.1W, 0.1Ω)*Overload prevention function*9 sets programmable memory*4 sets real time display*Voltage range: 1V~63V*Current range: 10mA~15A*Maximum power: 200W*Operation mode: CV, CC, CP and CR*Built in USB interface
-
Product
Rod End Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK’s Rod End Load Cells provide an excellent solution for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. You will find a capacity
-
Product
Network Analyzer, Tester, RJ45/RJ11, LED
72-9945
-
Quickly test RJ-45 and RJ-11 cables. Features LED's for each conductor for individual continuity testing.
-
Product
4 Ports 10GbE RJ-45 Network Mezzanine Card
NMC-4009
-
Ideal for enterprise network infrastructure and high-performance computing. 2 x Intel® ELX550 -AT2, 4 ports RJ-45 connector, 2 x PCIe 3.0 x4, RoHS compliant.
-
Product
Compact Network Appliance Platform With Intel® Atom® Processor C3000 Family, Six GbE And Four SFP+ Ports
NA362 for vCPE
-
*Intel® Atom® processor C3000 family (Denverton)*Four DDR4 R-DIMM up to 128GB or U-DIMM up to 64GB memory*Six 10/100/1000 Mbps Ethernet ports and four SFP+ ports*Wi-Fi/3G/LTE through PCI Express Mini Card slot*Supports Intel® QuickAssist Technology*Supports Intel® Data Plane Development Kit (Intel® DPDK)*Suitable for VPN, vRouter, firewall and other vCPE applications
-
Product
Attenuators & Loads
-
*High power handling 100W with a wide range of available attenuation values*Very low PIM <- 160 dBc with excellent return loss performance*Support for 7-16 or 4.3-10 connectors and optional 19 inch rack mount kit*Designed and produced to ISO 9001:2008 certification standards for reliability and quality
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-400B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
DC Loads
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers wideband multichannel DC decouplers for antenna diagnostic applications. Due its high bandwidth the device is suitable for all broadcast, cellular and Wi-Fi standards.
-
Product
Network Toner & Probe Kit
MT-7028
-
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
Product
SIM, Module, Receiver, 90 Series, Fully Loaded with pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106)
510170102
-
This fully loaded SIM module kit comes with 34 pairs of VTAC Standard Pass-Thru and Right Angle Inserts (610151106). This kit also includes two PCB brackets for securing module to PCB.
-
Product
Scalar Network Analyzers
-
An RF network analyzer used to measure amplitude properties like VSWR and Return loss of Device Under Test.
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
DC Load Bank
K-900
-
Kongter Test & Measurement Co., Limited
K-900 series are your best choice DC load bank with Kongter’s updated solutions. This new series resistive dummy load includes a series customized load bank models that feature rugged design and and excellent performance. They facilitate your work for DC load and battery capacity testing. With different models of DC load bank, it covers a wide range from 12V to 480V nominal voltages with current up to 600A. Its big TFT touch screen with vivid display makes it more user-friendly for setting and operation. Kongter’s new PC software make it easy for measurement monitoring and report print out.
-
Product
Load Testing vs. Stress Testing
-
A load test is a planned test to perform a specified number of requests to a system in order to test the functionality of the system under specific levels of simultaneous requests. A load test ensures that a web system is capable of handling an expected volume of traffic, and therefore is sometimes referred to as volume testing. The goal of a load test is to prove that a system can handle the expected volume with minimal to acceptable performance degradation. The threshold of acceptable performance degradation must be defined by the testers as some value considered acceptable to the end user so that users will not bounce from the site.
-
Product
1U Rackmount Network Appliance Platform With Intel® Atom® Processor C3558/C3758 And Up To 10 LAN
NA362R
-
The NA362R is powered by the Intel® Atom™ processor C3558/C3758 (Codename: Denverton). The low power 1U network appliance comes with six 10/100/1000 Mbps LAN ports and two or four 10 GbE SFP+ fiber ports. It is equipped with one pair latch-type LAN Bypass function for fail-over option as well as featuring BIOS console redirection. Furthermore, it supports the Intel® QuickAssist Technology which accelerates data processing and compresses cryptographic workloads. The network communication appliance also features the Intel® Data Plane Development Kit, which greatly boosts packet processing performance and throughput to improve data plane performance.The NA362R comes with four DDR4 R-DIMM/U-DIMM sockets that can provide system memory of up to 128GB and support both ECC and non-ECC memory types. It comes equipped with two 2.5" SATA3 HDD and one mSATA for sufficient storage. In addition to six 10/100/1000 Mbps LAN ports (Intel® i210 Ethernet controller), it also has options of two or four 10 GbE SFP+ fiber ports for high bandwidth and long-distance communications. I/O options also include two USB 2.0 ports and a serial console port. To ensure reliable operation, the 10-port network platform supports watchdog timer. Moreover, it also supports mainstream Yocto and Linux.
-
Product
Tension Load Cells
-
These Load monitoring systems are available in telemetry/wireless (RLP), self-indicating (LLP) and cabled non-indicating (WLP) versions. Towcell a 25kN, wireless tension load cell specifically engineered for the emergency services, salvage and 4 x 4 industries. Ruggedly built and highly accurate load link style load cell dynamometers allow for force and load monitoring across a broad range of industries and applications.
-
Product
High-Speed Networking And Video Products
-
We offer a variety of solutions to support the development of embedded systems using a variety of high-speed networking and video technologies, including ARCNET, CoaXPress®, DisplayPort, Ethernet, HD-SDI, IEEE® 1394b (FireWire), MOST®, Optical Transport Network (OTN), Synchronous Optical Networking/Synchronous Digital Hierarchy (SONET/SDH), T1/E1 and Fiber-to-the-Home/Passive Optical Network (FTTH/PON) protocols.
