Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Wideband Power Amplifiers
-
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
Product
Autonomous Pulsed Doppler Wind LiDAR System
Galion
-
The Galion LiDAR, distributed by SgurrEnergy, has been optimised for collecting data for wind power applications. The all-sky scanning capability enables many more data collection opportunities than VAD scanning alone.
-
Product
High Voltage Amplifier
HA-405
-
* 400Vp-p(±200V DC)* 400mAp-p(±200mA DC)* Bandwidth: ≦1MHz(200Vp-p) *Slew Rate: 500V/us *Gain(AMPL):0~90(10 Turn VR) *DC Offset: ≦0~±200V(10 Turn VR+SW) *Output Resistor: 50Ω *Microprocess Control Protection
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Low Noise Amplifier
-
Corech Microwave’s Low Noise Amplifier(LNA) frequency ranges from 1kHz to 67 GHz, featured with ultra low noise figure, high gain and compact size. Narrow-band & wide-band ready modules are available. Output power from +1dBm to +18dBm. 2.92mm – F, PIN, and SMA – F connector options are available.
-
Product
4 Channel 24.5~ 29.0 Gb/s Pulse Pattern Generator and Error Detector
CA9808
-
The UC INSTRUEMNTS CA9808 4 Channel 24.5 ~ 29.0 Gb/s (100Gb/s) Pulse Pattern Generator and Error Detector is a high performance, flexible and cost effective four channel Pulse Pattern Generator and Error Detector that can operate from 24.5 Gb/s to 29 Gb/s each Channel. 4 channel 29.0 Gb/s make it total up to over more than 100 Gb/s testing capacity. It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer.
-
Product
Pulse Radar Sensors
-
Non-contact pulse radar level transmitters are available in general purpose and intrinsically safe models for liquids and internisically safe models for solids with light, medium, and heavy dust.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Dual-Mode Charge Amplifiers
-
Dual-mode charge amplifiers represent a versatile solution for both piezoelectric charge mode and ICP® sensors. Among the advanced features offered by models 443B01, 443B02 and 2775C are an ultra-low noise floor, sensor fault detection, overload detection, a built-in calibration reference signal, and an RS-232 port for seamless computer control. Notably, model 443B02 features a long discharge time constant selection, ideal for capturing quasi-static events lasting several seconds, a capability particularly beneficial for ballistics and ammunition testing applications. Model 2775C features AC, DC, and servo outputs.
-
Product
40mA Multi-Channel Amplifier
-
For the precise nanometer movement of actuators and other piezo products, an amplifier is required. Multi-channel amplifiers allow you to control multiple actuators or piezo products with a single amplifier. The NV40/3 piezo amplifier was designed for controlling low voltage piezo elements. It includes a voltage amplifier, a display and a PC-interface. The high-resolution display shows the voltage of the actuator, along with the mode of operation and the temperature inside the amplifier.
-
Product
Waveform Amplifier 30 Volts Pk-pk
WA301
-
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
Product
Shaft Speed Pulse Generators and Shaft Speed Targets
-
Shaft Speed Targets are needed to generate a pulse for a Speed Sensor that is monitoring a shaft for RPM (Revolution Per Minute). Electro-Sensors Pulse Generators provide the shaft speed target needed for shaft speed detection with a sensor or switch. We have many options available for all your application needs including customizable split collar pulser wraps.
-
Product
USB Power Sensor - 100 MHz to 8 GHz, Average, Peak (Pulse)
GT-8551B
-
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
HDMI Audio Extractor with Audio Amplifier, RS-232 and IP Control
EMX-I-AMP
-
The EMX-AMP is a 4K HDMI Audio Extractor with built-in 50 watt audio amplifier for direct connection of 8 ohm speakers. The device also provides line-level stereo Aux audio input and allows audio mixing of HDMI audio with the Aux input. Volume can be controlled from the front panel, RS-232, or external digital rotary pot (encoder) that can be mounted on a wall-plate.
-
Product
Amplifier
AC-100
-
The voltage amplifier for connecting piezoelectric acceleration meters, microphones, and other primary voltage output transducers to FFT spectrum analyzers with the IEPE standard current output (ZET 017-U2, ZET 017-U8, A19-U2).
-
Product
12 Channels 1.0 ~ 17.0 Gb/s (200Gbps) Pulse Pattern Generator and Error Detector
CA9806-12
-
The UC INSTRUEMNTS CA9806-12 is a highp erformance, flexible 12 channels Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (200 G). It is combined with three sets CA9806 4 CH 1.0 to 17.0 Gbps Pulse Pattern Generator and Error Detector that incorporates an external one by 4 rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build-in 8.5 ~ 15 Gb/s eye diagram testing function.
-
Product
Waveform Amplifiers
-
Most waveform generators are limited to 20V pk-pk EMF output level. The WA301 waveform amplifier can be used to increase that level up to 30V pk-pk.
-
Product
Solid State Power Amplifiers
SSPAs
-
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
Product
1.5µm PM Fiber Amplifier ( PM EDFA )
HAPM4000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM4000 is a Polarization Maintaining Optical Amplifier which working in 1528~1563nm operating wavelength. Adopt Polarization Maintaining Erbium-doped fiber (PM-EDF), output optical power range 13~26dBm, extinction ratio >20dB.
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
-
Product
Isolation Amplifier Analog Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
Low Noise Amplifiers
-
High-intercept and high-gain low noise amplifier modules. Wide supply voltage range. Custom designs available through LNA design services.
-
Product
Pulse Generators
-
Pulse generators provide electronic pulses which mimic events from radiation detectors and are useful in set-up, diagnostics, and noise measurement in spectroscopy systems.
-
Product
Programmable Gain Amplifiers
-
Analog Devices programmable gain amplifiers (PGAs) provide excellent gain accuracy, channel-to-channel matching specifications, and low 1 ppm/°C drift. Set your gain with a simple serial or parallel interface from 1 V/V to over 4000 V/V.
-
Product
Pulsed Transmitter
-
Built to operate in harsh environments, the Pulsed Transmitter unit provides radar installation decoy protection in a compact footprint and is powered by a Dewey Generator.The unit is comprised of a power supply, power amplifier, signal generator and antenna, with a fiber optic command and control interface providing throughput speeds capable of 1.25 G bits/sec via 1310 nm, single mode, ruggedized fiber.
-
Product
Microwave Amplifiers
MShU Series
-
*Ultrawide Operating Frequency Range*Small Size*Low Noise Figure*Low Power Consumption
-
Product
VCOM Amplifiers And Calibrators
-
Renesas offers various VCOM amplifiers including rail-to-rail input-output operational amplifiers and rail-to-rail input-output buffers, as well as programmable VCOM calibrators that are ideal for display applications.
