Pulse Amplifiers
increase amplitude while keeping waveform. Also known as: Pulsed Amplifiers
-
Product
Instrumentation (Tacho) Amplifier
MS 2007
-
Instrumentation Amplifier is a customized unit to incorporate additional line filtering and spike suppression so that the amplifiers can operate directly off the main aircraft 28 volt system and amplifies the input signal according dynamic input configuration. This unit is capable of working without damage in both under and over voltage conditions. Designed for general aircraft applications.
-
Product
CATV Booster Optical Amplifier
HA5100
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Product
RF POWER AMPLIFIERS
BSA Series
-
RF Input:N-f, standard on rear panelRF Output:standard on rear panel<1 kWN-f<3 kW7-16-f<5 kWEIA 1 5/8Mains Supply:Line Power:<1000 VA100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter:via status displayAmbient Temperature:0 ... +45 °CStorage Temperature:-20 ... +85 °CRelative Humidity:up to 95% (non-condensing)Operating Altitude:up to 2000 m above sea levelVibration and Shock:MIL-STD-810 GCooling:forced air with integral blowerair intake from front, air exhaust at rear
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
5B Measuring Amplifiers
MA Series
-
Highest aim of our connection technology is user-friendliness. Very comfortable is the connection of our products to the most various sensors and signals.
-
Product
L-Band Separate Raman Fiber Amplifier
RFA6000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
EDFA Optic Amplifiers
-
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters including 10/100M, 10/100/1000M and 10G fiber converters, SFP fiber converters, manageable/unmanageable fiber converters, OEO fiber converters, POE fiber converters, fiber converter cards, and fiber converter chassis; transmitting distance from 2km(MM) to 150km(SM) with SC or LC or FC connectors.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
Product
Solid State GaN (Gallium Nitride) Amplifiers
-
Fairview Microwave’s solid state GaN (Gallium Nitride) power amplifiers (also called SSPAs) feature broad frequency bands ranging from 30 MHz to 7.5 GHz and very high gain levels from 43 to 60 dB. These GaN SSPAs also show impressive harmonic response (-15 to -20 dBc) under worst case conditions. Saturated output power levels range from 10W to 100W with 20% to 35% Power Added Efficiency (PAE). All of our high power solid state GaN amplifiers from Fairview have internally regulated single voltage supplies. Our GaN SSPAs are designed to withstand environmental conditions such as humidity, altitude, shock and vibration with an operating temperature ranges from -40°C to +85°C. Some models are also equipped with integrated heat sinks and cooling fans. Most designs are EAR99.
-
Product
Low-Noise Amplifiers
-
Broadband, narrowband, high-frequency, our extensive portfolio of LNAs is ready to tackle the toughest requirements. Don’t see exactly what you need? We have a vast library of pre-engineered building blocks ready to support any custom design.
-
Product
Suitable For Frequency And Pulse Sensors
SEM1600F
-
The SEM1600F is a cost effective “smart” powered conditioner that accepts all common process pulse signals with a frequency range between (0.01 to 65000) Hz in standard configuration and (DC to 1000) Hz in counter mode. Typical applications would be to measure flow or batch counting.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Testing)
PA60Bi
-
PA60Bi is the panel-mounted power amplifier, which can produce 3-phase current, with maximum RMS phase current of 60A and maximum output power of 800VA, and 4-phase voltage, with maximum RMS phase voltage of 120V and maximum output power of 60VA.
-
Product
FTTx Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM’s FTTx amplifiers are designed for PON, RFoG and SFU receiver equipment and are offered in small, plastic QFN packages with integrated amplifier and attenuator functions. All parts cover the full 45 to 1000MHz / 1200MHz CATV band. 5v and 12v solutions are offered with power consumption of ≤ 1.5Watts. MACOM’s FTTx amplifiers are characterized with industry standard photodiodes, covering optical input ranges from -12 to +3dBm and each sample EVK comes complete with a photodiode and APC connector.
-
Product
Digital andAnalog Distribution Amplifier
D/A-1
-
The D/A-1 Digital and Analog Distribution Amplifier is a digital and analog signal distribution product based on the the Intelligent Reference/TM-4D™ chassis and is the perfect way to distribute externally supplied signals without the need for multiple units. Most signal distribution products are limited to either analog or digital signals, but the D/A-1 distributes both.
-
Product
Microwave Power Amplifiers
-
Spanawave/Giga-tronics Microwave Power Amplifiers deliver outstanding performance and exceptional value. These ultra-broadband amplifiers have excellent pulse performance and modulated signal fidelity, ideal for testing in wireless communications, defense EW and radar testing and general purpose microwave laboratory applications. Have the power you need to overcome cable and switching losses, or to drive higher power mixers, detectors and very high power amplifiers.
-
Product
MOSFETs For High Frequency Amplifier
-
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
Product
Wideband GaN Amplifiers
-
The Teledyne RF & Microwave family of GaN-based amplifiers maximizes power density and efficiency, and establishes a new benchmark for small size in the 0.1 to 6.0 GHz range that operates over multi octave. With dimensions of 2.5"L x 2"W x 0.42"H at only 2.1 cubic inches, these modular, non-ITAR GaN amplifiers maintain the rugged design characteristics needed for harsh airborne and land based requirements.
-
Product
H2S Trip Amplifier Module
TA202A
-
The TA202A is a single-channel H2S Trip Amplifier Module for use with our H2S Intelligent Sensors. It is designed to monitor H2S in parts per million (ppm) levels and provide status indication and alarm outputs.
-
Product
High-end Cable DAC & Amplifier
Impacto universal
-
Beyerdynamic Digitalize high-end headphones.
-
Product
Amplifier Modules Band Specific
-
Modules are usually smaller and are usually part of systems. You supply your own DC voltage, make the connections and supply your own DC supply. Modules are available with or without heatsinks and fans. Amplifiers Modules are available in both Broadband and Band-Specific frequencies. Modular design concepts save time and money, and are lightweight, reliable, cost-effective solutions. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
E-Band Low Noise Amplifier MMIC
AWL-7186
-
The AWL-7186 is a 4-stage ultra-low noise amplifier that provides a noise figure of less than 3.5 dB, an output P1dB of +8 dBm, and an adjustable gain range of 15 dB. The MMIC features exceptional gain flatness and superior noise performance over a very wide bandwidth. It is implemented in 0.1 um GaAs PHEMT technology.
-
Product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
-
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
Product
Programmable Oscillator Amplifier
-
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
Product
Dynamic Power Device Analyzer/Double Pulse Tester
PD1500A
-
As an off-the-shelf measurement solution, the PD1500A delivers reliable, repeatable measurements of wide-bandgap semiconductors. The platform ensures user safety and protection of the system’s measurement hardware.
-
Product
Single-Ended to Differential Amplifiers
-
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
-
Product
Sample/Track and Hold Amplifiers
-
Analog Devices offers a portfolio of sample-and-hold amplifiers and track and hold amplifiers that combine speed with precision. ADI sample-and-hold amplifiers can acquire a signal in 700 ns and hold it with a droop rate of 0.01 µV/µs. These devices are up to 14-bit accurate, with low aperture jitter and output impedance, and they are available in commercial, industrial, and military temperature ranges.
-
Product
SOA & Raman Amplifier
-
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
Product
Super Low Noise Amplifiers
WCA Series
-
WCA series super low noise amplifiers have sub-0.5 dB noise figure at VHF band with several octave bandwidth. The amplifiers have 75 Ohm impedance.
