Simulation Testing
See Also: Simulation, Simulators, Simulation Software
-
product
Test Cells (
LaplaCell
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They \re calibrated according to the methodology of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing.
-
product
Magnet Testing
m-axis
m-axis is a measurement system that can be used to characterize permanent magnets in terms of their magnetic specifications (magnetic moment and magnetization angle) with high precision. In addition to the four standard measuring ranges, the modular design allows the system to be adapted to customer-specific requirements. The measurement systems can be used for 100% in-line quality control via our m-axis I/O module.
-
product
Testing Instruments
NDT testing instruments, other testing instruments, paper testing instruments, plastic testing instruments, rubber testing instruments, soil testing instruments
-
product
Test systems
MG Products can supply a variety of test systems. These include the Extended Boundary Scan Test from JTAG Technologies, the functional test equipment integrated into a table or high configuration from Unites systems or the Cabinet Modular Test solution (CMT). We offer the right solution for every test setup.
-
product
Microwave Testing
50A
The GGB Industries, Inc., MODEL 50A probe sets new standards in microwave probing performance. Using low loss coaxial techniques, the Model 50A achieves an insertion loss of less than 1.0 db and a return loss of greater than 18 db through 50 GHz.
-
product
Unit Testing
Hitex offers a unit testing service for C/C++ application source code using the well-known test tool TESSY. For this service, the customer provides their source code of the C/C++ functions to be tested, ideally along with the specifications of the functionality and comprehensive comments in the source code.
-
product
Connector Testing
If your product uses a connector or terminal, it can be susceptible to a unique set of failures that warrant specific connector testing conditions to determine the robustness of your design.
-
product
Welding Simulator
High-speed, direct resistance heating up to 10,000C/secondControlled cooling or accelerated cooling with optional quench (air/gas/water/mist)Simulation of multiple welding techniques and materialsAbility to test in vacuum, air or inert gasEasy to use controls and software, including DSI's custom Gleeble Welding Software
-
product
Test SIP
VoIP, Video, and IPTV products must withstand and continue to function when facing all the conditions that occur on the Internet. These include attacks from hackers exploiting vulnerabilities in security and protocols as well as the common phenomenon of congestion, delay, jitter, drops, and so on. VoIP, Video, and IPTV products must demonstrate robustness and resiliency in the face of unusual and/or illegal conditions.
-
product
Shock Testing
Shock testing typically involves calibrated, repeatable, violent events. The resulting energy is then absorbed transferred through the test specimen or Device Under Test (DUT)
-
product
Test Adapters
In our specially developed MG range of linear test adapters (test fixtures), we use solid aluminium components in our mechanical construction. This is to ensure the reliability and contact accuracy of the test adapter.
-
product
Test Systems
6TL’s speciality is simplifying the architecture of test systems, so that our customer’s Total Cost Of Ownership is drastically minimized. The technology that conveys our mission is called FastATE.FastATE technology is based on using intelligent modules to build test systems.
-
-
product
EMC/EMI Testing
MET Laboratories boasts proven, superior capabilities in Electromagnetic Compatibility (EMC) compliance testing, including wireless & RF testing. Our EMC labs are among the most respected in the U.S. Our EMC testing covers FCC Part 15, as well as Parts 18, 22, 24-27, 74, 90 & 95, and 101
-
product
Test Sockets
Smiths Interconnect offers a wide range of spring contacts and design standards for high quality test sockets providing flexibility and fast delivery for optimal cost/performance ratio.
-
product
GNSS Simulation Engine
Skydel
Test a wide range of applications with advanced GNSS Simulators and helpful tools that generate basic scenarios all the way to complex threat environments, leveraging the power and scalability of the Skydel Simulation Engine. Skydel powers each of Safran Federal Systems' advanced software-defined simulators including BroadSim, BroadSim Anechoic and BroadSim Wavefront.
-
product
Test System
LB302
Computer Gesteuerte Systeme GmbH
The LB302 test system is the most used midsize range version of the LB-300 series. It is designed for development as well as for production. The ‘device under test’ (DUT) is connected with a G12 receiver (Virginia Panel Company), which has a high number of possible contacting and a low transition resistance.
-
product
MIMIC® IoT Simulator
The MIMIC IoT Simulator creates a real-world test lab with many thousands of manageable IoT sensors, gateways and other connected devices to simulate your IoT environment related to*Industry 4.0*Smart Factories*Smart Cities*Smart agriculture
-
product
Custom Solar Simulation
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
product
Test Handler
M6242
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
product
Test Probes
Our innovative Test Probes are the upgrade version of Auto Multi Meter. It can perform multiple circuit system test such as power supply feed, voltage and resistance measurement, continuity test, ground test, polarity check and components activation.
-
product
iSimulator Impedance Simulator
Z1000
Measurements International Ltd.
With the release of the commercial Z1000 iSimulator, the process for calibration of LCR meters has been taken to a new level. The Z1000 covers the full calibration of LCR meters over simulated impedances from 100 Hz to 20 kHz while eliminating the need for external standards and providing a much simpler, easier-to-use method of LCR meter calibration.
-
product
Environmental Testing
Large Walk-in Environmental Chamber, and Walk-in Salt Fog Chamber, various sizes of vibration and shock equipment, and environmental chambers.
-
product
Torque Testing
Torque testers measure properties such as torsional strength and stiffness and are used in quality control of various fields including medical devices, metals, and aerospace
-
-
product
Hot Dipping Simulator
HDPS
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
product
In-Circuit Test
Test Coach has been delivering the highest quality in-circuit test programs since 1998. Our engineers have the education, experience and expertise needed to solve your most challenging test requirements. We partner with our customers to provide comprehensive test solutions, including consulting on: design for test, recommendations on the best hardware and software options to implement, test strategy, and long term planning for multi board projects. Our expertise allows us to really understand customer requirements, so that quotes are accurate and timely. However, we also understand that sometimes projects can change scope. At Test Coach, we have the flexibility to adapt to changes with as little impact to delivery as possible.
-
product
Loop Testing
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
product
Magnetic-Inductive Testing
MAGNATEST® Product Family
Foerster Instruments, Incorporated
The MAGNATEST product family is used for the non-destructive testing of metallic materials for magnetic and/or electrical properties. The test instruments are used in the automotive and aviation sectors as well as in the production of semi-finished products. The focus is on testing components relevant to safety such as brake discs, or ball pins and functional components such as camshafts and drive shafts, pivots and piston pins. Typical test tasks include hardness checks, material differentiation and sorting. MAGNATEST can also be used for the automatic testing for the geometric properties of all metallic series components. The high-performance amplifier installed in MAGNATEST test instruments makes it possible to analyze harmonics, which guarantees an extremely reliable and precise repetition, even when impacted by perturbations.
