PCMCIA Interfaces
-
Product
Interface Module
MIRIG
-
Мезонин MIRIG предназначен для приёма сигналов точного времени, их регистрации и синхронизации совместно работающего оборудования по протоколу IRIG-B
-
Product
*C Series CAN Interface Module
-
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Interfaces & I / Os
-
USBTucan is a USB-connected I / O box with digital inputs / outputs, analog inputs and a galvanically isolated CAN interface.
-
Product
IEEE488 (GPIC, HPIB) PCI Interface Card - Fits 3.3V or 5.0V Slots, 1KByte Transfer FIFO
GPIB-PCI-XL
-
The GPIB-PCI-XL is a PCI GPIB controller card that converts any PC with a PCI bus slot into a GPIB controller.
-
Product
Optical Head Interface
N7749C
-
The N7749C optical head interface can control two or four 8162-C series optical power meter heads. Readout is supported over LAN and USB interfaces with a built-in web-browser GUI and the SCPI command set common to Keysight optical power meters.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
VXI Register Interface Board
VXI-5524A
-
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
Product
Pressure Transducers with Serial(485) Interface
P855
-
The Validyne model P855 is a digitally compensated differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments.
-
Product
CAMAC Controller With USB Interface
CC-USB
-
The CCUSB is a full-featured CAMAC Crate controller with integrated high speed USB-2 interface and full CAMAC dataway display. It supports Master and Slave operations with complete CAMAC arbitration as well as auxiliary CAMAC controller operation.
-
Product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
-
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
-
Product
GPIB Parallel Interface
Model 4823B
-
* Provides 56 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Available with DIN connector on circuit side for piggyback mounting.
-
Product
USB 3.0 and Ethernet to VME Interface
SIS3153
-
The SIS3153 is the successor to our SIS3150 USB2.0 to VME interface.
-
Product
4-Port Serial Interface
APCI-7500-3
-
This Model has a 37-pin D-Sub male connectorRS232, RS422, RS485, 20 mA Current LoopModular structure through SI modulesWith or without optical isolationMode configuration free for each port128-byte FIFO-buffer, common interruptTransfer rate programmable up to 115,200 BaudOption: up to 1 MBaud for RS485 and RS422Automatic direction recognition for RS48Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)Transmission mode asynchronous, full, half duplexTransfer rate: progr. up to 115.2 kBaud up to 1 MBaud on requestProtocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bitsParity: even, odd, none, mark or spaceInterrupt lines: automatic through BIOS
-
Product
Hall Sensor Board with I2C Interface
048-368
-
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
PXI Interface Cards
-
PXI is a modular instrument system designed to take advantage of fast data interfaces based on PCI and PCIe bus systems. Due to the large number of different PXI interface cards, the individual test system can be designed for almost all applications.
-
Product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
-
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
Product
25 GHz differential probe with ProAxial interface
DH25-PX
-
25 GHz differential probe with ProAxial interface.
-
Product
18.5" 1366 X 768, VGA/DVI/HDMI Interface, Ultra Slim Touch Open Frame Monitor
IDS-3118W
-
18.5" 1366x768 HD LCD panel with LED backlight for 20% power saving and environmental protection. 0° ~ 55° C wide range operating temperature, 5-wire resistive and P-cap touchscreen solution, Touch interface: USB & RS-232.
-
Product
Low Profile PCI 24 Channel TTL Digital Interface
8018
-
The 8018 Low Profile PCI digital I/O interface provides 24 channels of buffered drive digital I/O emulating 8255 mode zero. The board can be utilized for PC-based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems.
-
Product
SIP-90-2 Test System Interface Probe
SIP-90-2
-
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
10.4" 800 X 600, VGA/DVI Interface, Ultra Slim Touch Open Frame Monitor
IDS-3110
-
10.4" 800 x 600 SVGA LED panel with LED backlight for 20% power saving and environmental protection. -20°C~+60°C wide operating temperature support, 5-wires resistive touchscreen solution.
-
Product
Hall Sensor Board with I2C Interface
050-382
-
Version: +5V/15A +12V/15A -5V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Serial Parallel Interface
Model 2303
-
* 2303 Board provides 40 high-power TTL I/O lines that can sink 23 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual Serial headers support conections with baud rate switch inputs or to a Serial Flat Ribon Cable Assembly. * Optional Relay Driver board drives 24-40 relays. * 114732 Board has the DIN connector on circuit side for use with the X3DVR Relay Driver Board or for piggyback mounting.* All other specifications are the same as listed above for the 2303.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
GPIB Parallel Interface
Model 4813
-
* Provides 128 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Optional Relay Driver boards add 64 or 128 Relay Drivers.
-
Product
Digital Multimeter, USB Interface, 20000 Count, True RMS, Auto Range, 4.5 Digit
72-7730A
-
Digital multimeter is a 20,000 counts and 4-1/2 digits with steady operation. The meter can measure AC voltage and current, DC voltage and current, resistance, capacitance, temperature frequency, diodes, continuity, 4 to 20mA loop, Max/Min, relative mode but also has data store, data recall, AC true RMS, AC+DC, low battery display, double display backlight, automatic power off and full overload protection.
-
Product
PCIe To PXIe Remote Control Interface Kit With Daisy-Chain Facility, 5m Cable
43-921-051-KIT
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules. The technology consists of a 53-921-001 host adapter installed in the host computer, a PCIe x8 cable, and a 43-921-00x, a remote controller with the 3U (Eurocard) expansion module. 53-921-001 comes in a PCI Express x8 footprint and equips with PCIe x8 cable connector.
-
Product
PXI/PXIe Remote Control Interface Modules And Kits
-
Take advantage of the latest high-performance, low-cost desktop PCs for control of your PXI system.
-
Product
Multi-channel Interface Module
PC104E-MA4
-
Alta Data Technologies’ PC104E-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC PCI/104-Express interface card supported by the latest software technologies. The PC104E-MA4 card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Ethernet To GPIB Instrument Interfaces
-
ICS's 9055 and 8055 Ethernet to GPIB Instrument Interfaces convert any GPIB instrument into a VXI-11.3 compatible instrument that does not require special drivers and is compatible with the following operating systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows systems with VISA or an RPC library. ICS's 9055 and 8055 use VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. To learn more about the VXI-11 protocol and how it benefits your system, download our new VXI-11 Tutorial or a copy of the VXI-11 Specification.
