Transceivers
both send and receive a signal.
See Also: Optical Transceivers, Vector Signal Transceivers, SFP, SFP Test
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
product
4-Channel Optical Transceiver
QSFP28 AOC
Eoptolink Technology Inc., Ltd.
Eoptolink QSFP28 Active Optical Cable is a 4-channel optical transceiver, which conforms to QSFP28 MSA and works at the rage of 25Gbps per channel. The AOC conforms to transmission speed required by InfiniBand™ EDR, 100 Gigabit Ethernet (100GBASE-SR4) and enables to transmit maximum 100m. Best for close-range high-speed transmission, for example, betweenserver racks, between servers.
-
product
Non-Isolated Controller Area Network (CAN)
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
product
Virtex UltraScale+ 3U VPX Plug-In Module
iW-RainboW-G47V®
AMD Xilinx’s VU13P, VU11P, VU9P, VU7P, VU5P Virtex Ultrascale+ FPGADual 64 bit, 4GB FPGA-DDR4 with ECC (Upgradable)31 channels of FPGA GTY transceivers up to 32.75Gbps1Dual ARM Cortex-A7 core processor of 1.2GHz speed32bit 2GB DDR4 for CPU with ECC128MB QSPI Flash & 256MB NOR Flash3U VPX Connector (P0+P1A & P1B+P2A)8 Optical transceivers through MT Ferrule Connector (P2B)
-
product
Wireless Conmmunications
1. Design and implementation of filters and oscillators for wireless communication. 2. Design and implementation of transceiver for analog wireless communication. 3. Design and implementation of telephone system and controllable. 4. Design and implementation of transceiver for digital wireless communication.
-
product
Wireless Receivers
Omega offers a full range of wireless reciever options. Form RS232-to-USB transceivers to long-range repeater/receiver systems, and connector/transmitter receivers.
-
product
10-Channel Optical Links Module
FMC410
Sundance Multiprocessor Technology Ltd.
The FMC410 is an optical transceiver module in the FMC form factor that offers ten independent optical transmit and receive links with maximum data rates of either 6.25Gbps or 10Gbps. This COTS card provides high-speed optical input and output for telecommunications, data networking, data storage, and ultra-high-definition video applications. The FMC410 can also be used as a dual 10Gb or dual 40Gb Ethernet port.
-
product
Optical tTansceiver Module
QSFP28
Eoptolink Technology Inc., Ltd.
Eoptolink’s EOLQ-851HG-02 QSFP28 SR4 100G Optical transceiver module are designed for use in 100 Gigabit Ethernet links over multimode fiber. They are compliant with the QSFP28 MSA and IEEE 802.3bm 100GBASE-SR4 and CAUI-4. Digital diagnostics functions are available via the I2C interface, as specified by the QSFP28 MSA.
-
product
PXIe-7911 , KU035 FPGA, x8 Gen 3 PXI Coprocessor Module
785172-01
The PXIe-7911 provides a Xilinx Kintex UltraScale FPGA that you can program with LabVIEW or Xilinx Vivado to add signal-processing capabilities to PXI Express systems. Using the x8 Gen 3 PCI Express architecture and peer-to-peer streaming, PXI FlexRIO Coprocessor Modules can stream data to and from other modules in a PXI chassis at up to 7 GB/s without a host controller. You can pair these modules with another PXI instrument, such as a PXI Vector Signal Transceiver, to add functionality, such as running complex algorithms in real-time. The PXIe-7911 KU035 FPGA is ideal for applications that require a moderate amount of signal processing.
-
product
Wireless Receivers
Omega offers a full range of wireless reciever options. Form RS232-to-USB transceivers to long-range repeater/receiver systems, and connector/transmitter receivers.
-
product
Communication Data Logger
LE-270GR
LE-270GR is a Communication Data Logger, which has acceleration sensor and a connector for GPS antenna. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data or GPS data on the PC at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on PC. It has galvanic-isolated two CAN transceivers and two LIN transceivers. Thus you can measure 2 channels of CAN/LIN communication lines and can simultaneously register GPS positioning data, acceleration data, and voltage data of 4 external signals.
-
product
Digital Video/Audio/Data optical transceiver
OD3000B
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD3000B digital series optical transceiver, adopts digital video coding technique and WDM technique to satisfied user's multipath digital video, audio, data, ethernet's long distant high quality optical fiber transmission because of its full-found. This model of optical transceiver including single fiber one way digital video, single fiber 64 routes video, 128 routes audio and data uni-direction and bi-direction complication. OD3000B optical transceiver can transmit the camera audio/video signal, camera and tripod head control data as well as other control function to central control room from remote end by optical fiber. It can be widely used in the remote monitoring, video conference, video medical, remote education and other systems of public road, traffic, industrial and mining, community ect.
-
product
Frequency Converter Upwards
UPCONVERTER 10 GHz LXI
UPCONVERTER 10 GHz осуществляет программно управляемый перенос вверх спектра шириной 150 МГц, поступающего на вход сигнала, в любую точку спектрального диапазона от 10 МГц до 10 ГГц. Перенос спектра осуществляется по супергетеродинному принципу с тремя ступенями переноса. Благодаря этому во всем рабочем диапазоне спектра достигаются высокие уровни подавления несущей частоты и зеркального канала. Также UPCONVERTER 10 GHz обладает уникальной возможностью, не имеющей аналогов среди приборов подобного типа – задавать значение промежуточной частоты (входного сигнала) для переноса в диапазоне от 50 до 400 МГц. Помимо этого, прибор позволяет передавать входной сигнал частотой от 0,1 до 400 МГц напрямую на выход, без переноса. Благодаря этому, совместно с UPCONVERTER 10 GHz в качестве генератора промежуточной частоты может быть использован широкий спектр генераторов зарубежного и отечественного производства. Холдинг «Информтест» предлагает потребителям генераторы собственной разработки MGKS and MGVCh , as well as the first Russian MT transceiver module , which are fully compatible with the input characteristics of UPCONVERTER 10 GHz. Together with generators produced by the holding "Informtest" UPCONVERTER 10 GHz under the control of a common software shell makes up a synthetic instrument - a ready-made solution for testing microwave devices and radio reception channels.
-
product
Cloud And Networking
From laser chips (EMLs, DMLs, and VCSELs) and pluggable coherent transceivers to pump lasers and TrueFlex® colorless/directionless/contentionless ROADMs, Lumentum’s comprehensive, vertically integrated portfolio lowers costs and speeds time-to-market. We optimize our components for best-in-class performance, creating flexible and scalable platforms that address ever-changing market conditions and product migrations. To ensure field reliability, Lumentum uses only the best materials and processes including stringent, proprietary burn-in processes during laser manufacturing.
-
product
Analyze RTL
ASICs and FPGA routinely have millions of gates with memories, transceivers, third party IP and processor cores. Problems can be time consuming and complex to debug in the lab and through simulations. Designers need verification tools that can identify problems quickly to reduce their verification and debug time before simulation, before synthesis, and definitely before burning chips in the lab.
-
product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Pump Laser Diode Driver
S-110
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
product
Transmitter Inhibit Controller
ALC-1
The Array Solutions ALC-1 Transmitter Inhibit controller interfaces between your amplifier’s ALC output, your PowerMaster PTT connections, and your transceiver’s ALC input to provide fast, rapid protection of your transceiver and amplifier when a sudden high SWR event occurs.
-
product
Serial Transceivers
Exar offers a complete portfolio of RS-232, RS-485 and RS-422 transceivers and the industry's largest portfolio of multiprotocol transceivers. At 52Mbps, Exar offers some of the industry's fastest RS-485 and multiprotocol transceivers.
-
product
RS-232
Renesas' RS-232 transceivers are available in many configurations and feature data rates up to 1Mbps, IEC61000 ESD protection, low power shut down modes, and small QFN packages.
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
product
Fiber Optic Talk Set
Fiber optic talk set consists of both the fiber optic light source and transceivers, which carry voice over the spare fiber in both directions. When doing the test work, technicians may need remote location communication during the measurement or splicing work, and sometimes radio-based communications may not be suitable because of environmental conditions such as FCC restrictions, etc. fiber optic talk set will function well in such cases, they could utilize the already installed fiber optic link to carry voice communications.
-
product
NI-5783, 40 MHz Bandwidth Transceiver Adapter Module for FlexRIO
784364-02
The NI‑5783 has DC‑coupled inputs with two variants: an elliptic filter variant optimized for frequency-domain applications and a Butterworth filter variant optimized for time-domain applications. The NI‑5783 is particularly well suited for applications in software defined radio, electronic warfare, high-performance machine control, and medical imaging. The NI‑5783 is compatible only with the PXI FPGA Module for FlexRIO modules that have a Kintex‑7 FPGA and the stand-alone Controller for FlexRIO.
-
product
Interface
Renesas offers industry-leading devices to enable efficient and reliable communication for industrial control, networking and computing applications. Dual protocol transceivers, voltage level translators, I2C Buffers, wide operating voltage range RS-232 transceivers, and RS-485/422 devices with the highest noise immunity and ESD protection in small packages are available to support high-speed data transfer and a variety of configurations to fit your applications.
-
product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
product
Pro Micro
5V/16MHz
Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
