Transceivers
both send and receive a signal.
See Also: Optical Transceivers, Vector Signal Transceivers, SFP, SFP Test
-
Product
Power Line Transceivers
-
Since the early 90s, ST is committed to supporting advances in narrow-band power-line communication (PLC) technologies that are now largely adopted by Automatic Meter Reading (AMR) and Automatic Meter Infrastructures (AMI) solutions at the heart of the Smart Grid concept.
-
Product
Single Beam Echosounder, Hydrographic Survey Boat
Z-Boat 1250
-
Teledyne Oceanscience Z-Boats® are the number one choice for reliable, remotely controlled, hydrographic surveying in streams, rivers, lakes, and coastal waters around the world.Whether you need to reduce survey time, keep people safe during hazardous conditions, or access hard to reach locations, there is a Z-Boat to suit your survey and your budget. The Z-Boat 1250 is easy to operate. The integrated echosounder has an embedded transceiver with digital signal processing and outputs depth & temperature using NMEA 0183 data output.
-
Product
Optical Transceiver
RJ-11
-
The next generation of optical transceiver has arrived with the introduction of GCI's RJ-11 Optical Transceiver. This fully SEMI compliant and Hokuyo compatible unit is the choice of leading 300mm FABs and equipment manufacturers throughout the world to simplify installation and maintenance of their E84 communications.
-
Product
Fiber Optic Transceivers
-
Shanghai Tarluz Telecom Tech Co., LTD
Also known as Optical Transceiver or Optical Module. It is a small packaged device that uses fiber optic technology to transmit and receive data.
-
Product
QuadPOD Conditioning Interface
JT 2147/VPC
-
The JT 2147/VPC is a variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within Virginia Panel Corporation’s mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry, two independent, programmable TAP modules (of type JT 2149) and two TAP modules with I/O (of type JT 2149/MPV) on a single board that interfaces via the VPC QuadraPaddle connectors type G20x or G14x.
-
Product
PCIe-Mini Module
PCIe-Mini-1553-2
-
The ALPHI PCIe-Mini-1553-2 uses DDC Total-Ace communication device as its 1553 bus controller, or remote terminal with concurrent Bus monitor terminal. Dual controller has a Dual redundant channel with built in transceivers and transformer. The controller has the capability to emulate up to 31 RT addresses simultaneously. The PCIe-Mini-1553-2in RT mode can filter on RT address, T/R, Subaddress. The PCie-Mini-1553-2 is offered is extended temperature. The board format is a full PCIexpress Mini board.
-
Product
VNA
ZTXR-Series
-
The RPG ZTXRxxx millimeter-wave transceivers are optional for the following four-port vector network analyzers:
-
Product
Low Power MIPI Bridging Solution With Integrated Flash
CrossLinkPlus
-
*Instant-on (< 10 ms) configuration with integrated flash memory*Integrated flash enables flexible reprogramming in the field*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per port*11 programmable, source synchronous I/O pairs for camera and display interfacing*Available in small 3.5 mm x 3.5 mm BGA package with 0.4 mm pitch*Comprehensive library of IP and reference designs, compatible with CrossLink
-
Product
TRC-8542, CAN HS/FD Transceiver Cable
783699-03
-
The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is … an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
Product
TRC-8543, CAN HS/FD or LS/FT Transceiver Cable
783701-02
-
CAN HS/FD or LS/FT Transceiver Cable—The TRC-8543 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8543 to the port to support a CAN HS/FD or LS/FT interface. The TRC-8543 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
Product
Vector Signal Transceiver-based Radio Solution (VRS)
ATS-3100 VRS
-
The ATS-3100 VRS, the newest member of the ATS-3100 PXI Integration Platform product family and fifth-generation radio test solution, is a single, consolidated platform for testing legacy, modern, and next-gen, software-defined radios for military, civil, and commercial users. Integrating the PXI Vector Signal Transceiver (VST) from National Instruments (NI), the platform enables faster test time with wider bandwidth (up to 1GHz) than any other radio test solution available today.
-
Product
SFP Module
F-3000
-
The DIAMOND flexos SFP modules (transceivers) make it possible to transfer data via fibre optics. The SFP modules are available for multi-mode and single-mode, Gigabit and Fast Ethernet. The SFPs have metal housings with latches for the simple removal of the module. They are compatible with connector types F-3000™ or LC.
-
Product
Fully Compliant ASi-5 Transceiver ASSP
ASI4U-V5
-
The ASI4U-V5 is the industry’s first silicon solution to fulfill the ASi-5 (Actuator-Sensor-Interface version 5) standard for industrial network equipment that enables comprehensive Industry 4.0 applications. The ASI4U-V5 ASSP comes with a completely verified and field-proven firmware that fully implements ASi-5. Hence, integration of ASi-5 into any application is very easy, as the complexity of the fieldbus is hidden by the chip and the firmware.
-
Product
PCI Module
PCI-1553-B
-
The PCI-1553-LXE/DXE 1,2 uses UTMC’s Sµmmit LXE/DXE version, UT69151DXE-GPC 1553 communication device as its 1553 bus controller, or remote terminal, or monitor terminal. A single controller has two redundant channels. The 1553board can have 1 or 2 communication channels. The controller accesses 64Kx16 word of external memory and has internal transceivers for both channel A and B. The 3U PCI board has on-board transformers for both channels and both controllers.
-
Product
TS Stream Optical Transceiver
OD2000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OD2000 digital fiber transmission system is designed and produced specially for long transmission and network construction of DVB DTV TS stream. OD2000 can modulate the MTS program signal (coming from the 1~8 ways separate multiplexer at the head-end generator room) to FMTS optical signal high-speed code stream. It is an important device to transmit TS stream between DTV head-ends.
-
Product
DACs / AOCs
-
Shenzhen Wiitek Technology Co.,Ltd
In both active and passive variants, DACs feature copper wire that connects two fixed transceiver modules on either end. AOCs, on the other hand, use multimode fiber to connect permanently attached transceivers. Both function as alternatives to purchasing individual modules and cables separately.
-
Product
Digital Input/Output Card
IOD-144
-
This is a 144-bit full-size card. A Programmable Peripheral Interface chip, type 8255-5 provides three 8-bit ports (A, B, and C) for each 24-bit group. Each port can be independently programmed for either input or output. Port C can also be configured as two 4-bit ports. These cards fully implement Mode 0 of the 8255 PPI chip. (Consult the factory if you desire to operate in Mode 1.) Type LS245 bi-directional transceivers sink 24 mA (optionally 64 mA) and source 15 mA. These transceiver buffers provide hysteresis correction on inputs and added drive capability on outputs. The direction of the transceivers is set by software.
-
Product
Interface RS-485 and RS-422
-
The RS-485 specification meets the requirements for a truly multipoint communications network, and the standard specifies up to 32 drivers and 32 receivers on a single (2-wire) bus. Some RS-485 transceivers modify the input impedance to allow up to 8× more nodes to be connected to the same bus. Analog Devices offers a wide range of standard RS-485/RS-422 transceivers and iCoupler® isolated RS-485/RS-422 transceivers to suit many applications.
-
Product
PCI-8433, 4-Port, PCI, Isolated, RS485/RS422 Serial Interface Device
779146-01
-
The PCI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
-
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
Product
Communication Data Logger
LE-270A
-
LE-270A is a Communication Data Logger, which records CAN/LIN communication logs in the SD/SDHC card for long hours. Using with a PC, it performs as a CAN/LIN protocol analyzer, and monitors data on the PC at real time (Line Monitor). Using without a PC, it performs as the CAN/LIN data logger, and saves data in the SD/SDHC card. It has two High-speed CAN transceivers, two Low-speed CAN transceivers and two LIN (TJA1020) transceivers. It monitors two channels of CAN or LIN, or one CAN and one LIN transceivers. In addition, four channels of Analog/Digital signals can be recorded.
-
Product
Xilinx Artix-7 FPGA SoM
TE0710
-
Sundance Multiprocessor Technology Ltd.
TE0710s are industrial-grade FPGA modules integrating a Xilinx Artix-7 T FPGA, a gigabit Ethernet transceiver (physical layer), 1 Gbit (128 Mbyte) DDR3 SDRAM with 8-bit width, 32 Mbyte Flash memory for configuration and operation, and powerful switch-mode power supplies for all onboard voltages.
-
Product
Isolated RS-232
-
Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.
-
Product
NRZ Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
Product
PXI Vehicle Multiprotocol Interface Module
-
PXI Vehicle Multiprotocol Interface Modules use hardware-selectable NI-XNET Transceiver Cables (TRC) to communicate High-Speed/Flexible Data‑rate CAN, Low-Speed/Fault Tolerant CAN, and/or LIN. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN and/or LIN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. PXI Vehicle Multiprotocol Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
18 GHz Up/Down Converter & Signal Conditioning
SC2250
-
The SC2250 extends the useful range of traditional 6GHz RF instruments for operation at microwave frequencies up to 18GHz. It provides excellent integration capability with other modular products such as National Instrument’s Vector Signal Transceiver (VST). Selectable filtering is provided for signal conditioning applications requiring spurious and harmonic rejection.
-
Product
Enhanced 16 Differential I/O Multi-Mode Transceiver Channels
DF2
-
Function module DF2 (Enhanced Version) multi-mode transceivers with 16 programmable I/O channels. Differential transceivers increase resistance to noise by creating two complementary signals. These complementary signals produced on balanced lines double noise immunity by creating lower power requirements due to lower supply voltages.
-
Product
Quad 12 Gsps 16-bit DAC& Dual 6 Gsps 12-bit ADC
ADF-QMx42
-
The DEG ADF-QMx42 FMC leverages the Analog Devices AD9082 MxFE (Mixed Signal Front End) transceiver technology. This highly integrated device includes a quad 16-bit, 12 Gsps sample rate radio frequency (RF) digital-to-analog converter (DAC) and a dual 12-bit, 6 Gsps rate RF analog-to-digital converter (ADC). The ADF-QMx42 features an 8-lane, 24.75 Gbps JESD204C transceiver port, an on-chip clock multiplier, digital signal processing capability and supports four transmitter channels and two receiver channels.
