Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 32.7k Ohm
50-293-032
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Programmable Resistors
-
Part of our Sensor Simulation family, these PCI programmable resistor cards are ideal for medical, aerospace and automotive applications.
-
Product
Open-source CAD tool to simulate 2D and 3D-ICs.
IntSim v2.0
-
Simulate and optimize 2D and 3D-ICs. Pre-silicon estimates for die size, number of metal levels, size of each metal level and chip power.
-
Product
PXI Resistor Module 2-Channel 1.5R to 4.09k with SPDT
40-293-123
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 65.5k Ohm With SPDT
50-293-133
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Arbitrary Waveform Generators
-
Helps you to generate with confidence waveforms of almost any imaginable shape: complex signals like digital modulations, RF stimuli for functional and performance tests, radar simulation, optical communication and electronic warfare can be created through an easy to use interface.
-
Product
AC/DC Leakage Current Tester
228
-
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
Product
Test Hardware
TTPSimulate PCI
-
TTPSimulate supports hardware-in-the-loop simulation and design of complex distributed control systems where some parts of the systems are physically available and others exist only as a simulation model. This board enables concurrent engineering and reliable integration of complex integrated systems in large programs.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 31.5Ω
50-298-010
Programmable Resistor Modules
The 50-298-010 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Bidirectional DC Power Supply + Regenerative Load
62000D
-
Chroma Systems Solutions, Inc.
Chroma 62000D programmable bidirectional DC power supplies have both power source and load characteristics, two quadrant operation, and allows feedback of the power from the DUT. They can be used for testing renewable energy power systems including PV/storage hybrid inverters, power conversion system (PCS) on charging/discharging, and as a battery simulator. The 62000D also is a fit for testing power components used in electric vehicles, such as bidirectional on-board chargers (BOBC), bidirectional DC convertors, and DC-AC motor drivers, and power conversion simulation tests of batteries in both directions.
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
Engine Torque Pulse Simulation
ETPS
-
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
UXG X-Series Agile Vector Adapter, 50 MHz to 20 GHzNEW!
N5194A
Vector Baseband Generator
The N5194A is part of the UXG family of signal generation products designed for threat simulation; simulate complex signal environments for radar/EW.
-
Product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
-
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
Product
Express Card
DAS-429ExCARD/RT10
-
Both cards contain 64 Kbytes of true dual-port RAM, for data blocks, control registers and Look-up table.The card's small size (54 millimeter wide) and suitability for Express Card compatible notebook computers make it a complete solution for developing and testing ARINC-429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The cards are supplied with C drivers, including source code, Mystic Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
PXI BRIC8 FIBO Matrix Dual 120x4 3pin brkout
40-592A-106
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
MIMIC® JUNOS Simulator
-
MIMIC JUNOS Simulator fully supports Juniper JUNOS® software and SNMPv1, v2, v2c, v3. Up to 100,000 devices can be simulated in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. An extensible environment allows new MIBs and devices to be added to the simulation.
-
Product
Software
Battery Simulator
-
Chroma Systems Solutions, Inc.
Testing battery connected devices with an actual battery can either be cost or time prohibitive especially if multiple channels are required. Our Battery Simulation software is used to validate device functions during development in lieu of an actual battery or batteries. Automotive applications include motor drivers, OBC, DC-DC convertors or chargers, and products of DC bus.
-
Product
VeriStand
-
VeriStand helps you get your hardware-in-the-loop or test cell control and monitoring system up and running quickly. With a wide range of out-of-the-box functionality that includes configurable data acquisition and logging, test sequencing, and simulation model integration, VeriStand reduces the time needed to test your products. You can also use a variety of software tools to add custom functionality to VeriStand, which makes it flexible enough to adapt to even the most complex applications. Choosing VeriStand gives you the confidence that your test system will perform reliably while providing the flexibility you need to meet your real-time test requirements.
-
Product
Temperature & Humidity Testing
-
DATASYST Engineering & Testing Services, Inc.
DATASYST can simulate both high and low temperature with humidity conditions. Cycle rates are dependent upon individual chamber capabilities and whether or not a unit under test is powered or not. DATASYST provides humidity testing for a range of industry specifications and can work with you on your customized testing requirements.
-
Product
Computational Lithography
-
ASML's industry-leading computational lithography products enable accurate lithography simulations that help to improve chip yield and quality
-
Product
Smart Protocol Analyzer
-
Works transparently over the Computer's I/O ports (serial & network). The analyzer supports Modbus, Fisher-ROC, BSAP, DNP and other Protocols. In addition to monitoring, this tool is capable of simulating Master and Slave devices.
-
Product
Shock Control
-
Shock testing simulates an extreme event that a unit under test is exposed to during handling, shipment, explosive event and/or daily use (e.g. dropping an object). The profile for this type of testing is defined by the shape of the time domain waveform together with its amplitude and duration. The m+p VibControl vibration control system offers full functionality for classical shock and shock response spectrum testing as well as for tests using external pulses or the capture of transient signals.
-
Product
Multi-Spool Network Simulation & Latency Solutions
Fiber Lab 750
-
from M2 Optics provides the perfect combination of flexibility and efficiency when requiring spools of fiber for testing, latency, and system demonstration applications.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 31.5Ω
40-252-110
Programmable Resistor Modules
The 40-252-110 is a programmable resistor module with 2 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Sea Water Immersion Test Device
-
Guangdong Bell Experiment Equipment Co.,Ltd
Sea Water Immersion Test Device Relevant standards requirement:Test Object: Battery storage pack or system.The test object connects all the wiring harness, connector and other parts according to the whole vehicle connection mode. Select one of the following two methods to operate test at the room temperature.Immerse the test objects (in the direction of real vehicle assembling) into 3.5% NaCl solution (mass fraction, simulated under normal temperature water composition) for 2 hours. The water depth is to be sufficient to completely submerge the test objects.Test objects according to GB/T4208-2017 part 14.2.7 test method and test process.
