Triaxial Accelerometer
A three-axis accelerometer that can simultaneously measure acceleration in all three directions. (www.ncbi.nlm.nih.gov)
-
Product
High Current Triaxial Cable, 4 A, VOLT:DC 60V
PX0104A
-
The Keysight PX0104A is suitable for high current measurement up to 4 A DC. It supports the Keysight M9602/03A.
-
Product
Linear Accelerometer Switch
-
Columbia Research Laboratories
Columbia Research Labs Accelerometer Switch is designed to interface with electrical or mechanical systems to control, safeguard against, or warn of undesirable variations in DC and low frequency acceleration. This sensor is available with a selectable switch point, a single or Bi-polar switch, and a choice of input power.
-
Product
IEPE Monoaxial Accelerometer – 100 mV/g
HDP352C34
-
Monoaxial accelerometer general purpose, ICP, 100mV/g, weight 5,8 g, range 50 g pk
-
Product
Digital Accelerometer
ZET 7052-N
-
Digital accelerometer ZET 7052-N is equipped with a compact sensing element and is designed for linear acceleration and vibration acceleration variable constituent measurement via three mutually perpendicular planes. Small weight of sensing element (1,5 g) considerably reduces self-mass load and compact dimensions (8,5×8,5×8,5 mm) enable use of the digital accelerometer ZET 7052-N for vibration measurements in systems with small active area.
-
Product
General Purpose Single Axis Accelerometers
-
Motion of a rigid body can be characterized within six degrees of freedom. Providing mechanical excitation to simulate this motion as may be encountered in the real world can entail a variety of test machines. There are various pound/force vibration shakers for structural testing. Regardless of the apparatus, the goal is always to ensure that the product under test can adequately perform, and reliably survive, in the environment in which it will be deployed, or to which it will be exposed during transport. PCB® accelerometers provide the measurement signals needed to control the vibratory input and to analyze the product’s reaction to such testing.
-
Product
Quantum Accelerometer
-
A quantum accelerometer uses atom interferometry to measure accelerations along a horizontal axis. Quantum accelerometers are able to achieve a combination of sensitivity and stability by exploiting quantum interference. As such, they will be critical components of a quantum inertial navigation unit, which will offer satellite-free navigation with unparalleled long-term accuracy. A phase locked SolsTiS system underpins this setup and provides the extremely low phase noise required to make high sensitivity measurements and dynamic frequency tunability to address multiple atomic transitions.
-
Product
Accelerometers | Vibration Sensors
-
Accelerometers measure the levels of vibration in an engine or system. They detect faults and prevent potential damage. They enable you to achieve the reliability and accuracy you need for your engine, aircraft, helicopter, UAS, space or transportation application.
-
Product
MEMS Accelerometer
SQ-XLD
-
The acceleration sensor module performs calibrated acceleration measurement with digital serial output. Using a USB or RS232 interface cable (sold separately), it functions as a self contained data acquisition system for 2 axis or 3 axis acceleration, tilt, and vibration measurement.
-
Product
Miniature Single Axis Accelerometers
-
Miniature piezoelectric accelerometers are required for applications demanding high frequency range, small size, and low weight. Product testing is necessary in today’s competitive marketplace in order to optimize designs, reduce defects, and improve customer acceptance and satisfaction. Shock and vibration testing offers a structured approach for verifying survivability in environmental influences that may be encountered during service and for precipitating incipient failures so they are not encountered by the end-user. PCB® accelerometers are used extensively for monitoring an object’s response to a programmed vibration input and for controlling the vibration profiles during testing.
-
Product
SparkFun Triple Axis Accelerometer Breakout
KX134 (Qwiic)
-
This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX134 digital accelerometer from Kionix. The KX134 is a low-power, 16-bit resolution three-axis accelerometer capable of measuring ±8g/16g/32g/64g (user-selectable) and has up to a 10kHz output data rate making it ideal for high-g measurements as well as high-speed applications such as vibration sensing.
-
Product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
-
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
Product
SparkFun Triple Axis Accelerometer Breakout
MMA8452Q
-
This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
Endevco Piezoresistive Undamped MEMS Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee.
-
Product
Gyros & Accelerometers
-
Aero Engineering Support Group
Litton, Delco, Smith, Honeywell, Collins, Allied Signal, Bendix, Rate Gyro, Vertical, Gyro, Directional Gyro, Accelerometers.
-
Product
Accelerometer with Built-In Preamplifier
NP-3000 series
-
This sensor converts mechanical vibrations into electric signals in proportion of vibration acceleration."The NP-3000 series offers ultra-small masses of 0.4g, tri-axial type which can obtain vibration directions of XYZ at once, waterproof, high sensitive type, and so on. You can choose the most suitable detector according to the purpose of use, operation conditions, and applications. Since the preamplifier is built in the detector main body of the NP-3000 series, sensor signal input part can be made relatively inexpensively and it can be directly connected to analysis equipment such as our FFT analyzer."
-
Product
High Sensitivity ICP® Accelerometers
-
High sensitivity ICP® accelerometers are specifically designed to enable the detection of ultra-low-level, low-frequency vibrations associated with very large structures, foundations, and earth tremors. These sensors typically possess exceptional measurement resolution as the result of its comparatively larger size, which furnishes a stronger output signal and a lower noise floor. All units are hermetically sealed in a titanium or stainless steel housing. Models that include a 2-pin, military style connector provide the added benefit of being electrically case isolated for superior RF and EMI protection.
-
Product
SparkFun Triple Axis Accelerometer Breakout
LIS3DH
-
The LIS3DH Breakout is a smart, low-power, three-axis, capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add translation detection to your project. It would be classified as a 3DoF, or 3 Degrees of Freedom. Inertial Measurement Units (or IMUs) can provide additional space location data, such as gyroscopic or magnetometric. The LIS3DH provided on this breakout operates under the same principles but gives a few analog inputs to play with, and it has some built-in movement detection abilities.
-
Product
Test Accelerometer Sensitivity And Noise Test
Accelerometer Test Unit
-
*Quick and Accurate Accelerometer Test*Battery operation*All tests use 32-bit resolution A to D Converter*All data downloaded to PC via Ethernet link*Records all data to a flexible easy to use database*Records time and date of tests
-
Product
Miniature Accelerometers
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
These piezoelectric accelerometers are particularly suited for small and light test objects. Of particular advantage may also be their high resonant frequencies. Due to the piezoelectric principle with its wide dynamic range both high acceleration and lowest vibration can be measured with the same sensor.
-
Product
Triaxial Cable For Current Higher Than 1 A (1.5 M Or 3 M)
16493L
-
16493L can be used as a general purpose triaxial cable for high current applications up to 4.2 A DC and 200 V. It can also be used for low current applications down to the sub-pA level.
-
Product
Special Accelerometers
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
This page shows vibration sensors for special applications.The Seat Pad Accelerometer Model KS963B100-S was developed for measuring whole body vibration transmitted by driver seats of building machines and other vehicles in compliance with ISO 10326-1 and ISO 7096. The sensor has an IEPE output for robust signal transmission.
-
Product
Low Leakage Triaxial Cable (0.4m / 0.8m / 1.5m / 3m / 4m)
16494A
-
16494A is suitable for low current applications down to the sub fA level. It supports a maximum voltage/current of 200 V / 1A DC.
-
Product
Accelerometers - Special Purpose
-
Analog Devices accelerometers and iSensor® MEMS accelerometer subsystems provide accurate detection while measuring acceleration, tilt, shock, and vibration in performance driven application. Our portfolio leads the industry in power, noise, bandwidth, and temperature specifications, and offers a range of MEMS sensor and signal conditioning integration on chip. Our MEMS-based Circuits from the Lab® reference designs have been built and tested by ADI experts to help you jumpstart your next system design.
-
Product
Servo type Accelerometer
-
A motion is sensed by a displacement detector, a current is fed to the coil to get back the pendulum mass to the original position. This current will be proportional to the acceleration, that is converted to an output voltage. The Servo type accelerometer is for the Earthquake Monitoring or measurements of micro tremor on the Civil Engineering Structures because of its higher sensitivity and stability or more accurate phase responses in the lower frequency range than those of other vibration transducers.
-
Product
Structural Test ICP® Accelerometers
-
Conventional structural test data systems use few to several hundred sensors. Cables bundles can be complex and confusing resulting in setup errors. Sensors with TEDS (Transducer Electronic Data Sheet) allow for an internal sensor digital chip to store sensor information. This information contains descriptive identifiers that when connected to a TEDS compatible signal conditioner or data system, reads the descriptive information and automatically aligns the data system. Human error is minimized, reducing time consuming data verification or re-test. The Series 333 ICP® accelerometers, and their accessories, are designed to address the needs of multi-point modal and structural test measurement applications. This equipment was developed in conjunction with the world renowned University of Cincinnati Structural Dynamics Research Laboratory and proven in real-world testing situations. The PCB 333 Series accelerometers delivers rapid system setup, reduces human documentation errors, maintains calibration data of each sensor, allows for “Plug-and-Play” installation, reduces overall test time lowering project test costs.
-
Product
1-axis Accelerometer GF1
-
Panasonic Industrial Devices Sales Company of America
Acceleration sensor
-
Product
PCB IMIB01, 100 mV/g, IEPE, 15 kHz, 2-Pin, Accelerometer, Industrial Vibration Sensor
784176-01
-
The PCB IMIB01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound
-
Product
PCB IMIC01, 100 mV/g, 2-Pin, Accelerometer, Industrial Vibration Sensor
780985-01
-
The PCB IMIC01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMIC01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
Product
Accelerometer & Platform Test Bench
mS 1115
-
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
