Electrical Testers
-
Product
Shore A Type Hardness Tester Rubber Hardness Tester
HS-A
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS-A is a digital Shore A type hardness tester. It is suitable for plastic (such as film, medical appliance, etc.), synthetic rubber(such as seals, tires, rubber roller, rubber hose/belt, wire and cable, shock absorber, etc.) and other related chemical products.
-
Product
Bare Board Tester
1232
-
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
Product
Analogue (1kV below) Insulation Tester
8031 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 2Ω & 20Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
Product
IEC60065 Fig11 Australia UL Plug Socket Tester Socket Outlet Torque Tester
CX-CTN
-
Shenzhen Chuangxin Instruments Co., Ltd.
The plug torque tester conforms to the standard of IEC60065 figure 11. It is used for checking whether the mechanical stress which occurs when the Direct Plug-in Equipment with plug pin normally insert into the socket is in the required range.
-
Product
Insulation Resistance Tester
UDH-50-1-T
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated•Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV •Resistance range to 1TΩ •Continuous digital display on LCM•Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
Product
Pendulum Impact Testers
-
Qualitest offers Charpy / Izod Impact Testers with capacities up to 750J meeting and exceeding ASTM E23, ISO, DIN, JIS, standard requirements. The key benefits of this line of top technology models are price competitiveness, extremely high precision and durability, automatic motorized lifting of the pendulum hammer to optimize cycle times, flexibility, efficiency for low/high temperature testing, and much more. Optionally we offer temperature chambers, automated sample handling, centering device, Charpy sample preparation and broaching machines for preparation of notched bar specimens.
-
Product
Din Abrasion Resistance Tester
SG-P01D
-
This tester is used to determine the abrasion characters of elastomers, rubber, soft synthetics, leather. etc or is with characters of high efficiency, good reproducibility and easy operation.
-
Product
12-48V Digital Display Circuit Tester
1674A
-
Peaceful Thriving Enterprise Co Ltd
Check on 12, 24 and 48V systems.
-
Product
Alternator/Battery Load Tester
6031
-
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
Product
Durable Hand-Held Battery Tester
6029
-
• Test 6 & 12 Volt batteries, alternators and starters• 125 Amp fixed load• Made in USA of US and Global Components
-
Product
Insulation Testers
AD-902
-
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
Product
Outsole Belt Flexing Tester
UI-FT36
-
Outsole Belt Flexing Tester, which is also named as Bata Belt Flex Tester, is used to test sole flexing resistance ability. Belt Flex Tester is designed and applicable to SATRA TM133 Resistance to crack initiation and growth–belt flex method.
-
Product
Dissolution Tester Accessories
-
Teledyne Hanson's diverse range of dissolution tester accessories significantly expands the functionality of their instruments, catering to various applications such as small volume testing, Chinese small volume testing, semisolids testing, and immersion cell usage per USP <1724>. The lineup includes:- Precision dissolution vessels- Vessel covers- Paddles (USP Apparatus 2)- Baskets (USP Apparatus 1)- Paddle over disk “transdermal sandwich (USP Apparatus 5)- Rotating cylinder (USP Apparatus 6) - Sampling probes- Small volume kits- Filter block kits- Humidity-sealed dosage-drop chambers- Stationary basket and cover
-
Product
Course Length Tester
TF124
-
TESTEX Testing Equipment Systems Ltd.
Course Length Tester, to determine the accurate length of a complete course of knitted fabric. When the yarn is attached to the clamp and wound round the pulleys, the length indicated on the ruler by the weighted clamp is added to that indicated on the appropriate location in use to give the total length of yarn.
-
Product
Digital Battery Testers
-
Electronic devices designed to test the remaining capacity of a battery's overall charge.
-
Product
Low Pressure Cylinder Leak Tester
CLT4PB
-
Tests leakage at 35psi compared to 100psi in current leakage tester. Lower pressure prevents smaller bore cylinders from moving as they might under 100psi. Works well on small engines found in recreational, marine and other applications.
-
Product
Auto Tensile Tester
ATT-03
-
Jinan Leading Instruments Co., Ltd.
ATT-03 Auto Tensile Tester is applicable inthe test of physical mechanical properties of plastic films, laminated materials, flexible packaging materials, plastic flexible tube, adhesives,adhesive tapes, pressure sensitive tape, adhesive bandage (plaster), releasepaper, protective film, flip off cap, foil, diaphragm, back sheet, non-woven, rubber and paper fiber, etc. It can perform the test items of tensile, peeling,deformation, tearing, heat seal, adhesive, puncture force, open force,low-speed unwinding force and unsnapping force, etc.
-
Product
Package Drop Tester
-
The Package Drop Tester - PDT-II Series simulates the drop/fall of the packaged finished products to evaluate their damages. All the rhombohedrons, angles and faces of the package container can be tested. so that the manufacturer can know how to take measures effectively to protect Its products against damage during transportation. During dropping, the carrier will rotate to allow the packed products to fall freely.lt can test the faces, edges and corners of the product, with small vibration, and stable and reliable operation.
-
Product
Network Cable Tester
PA-40
-
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
Data-logging Circuit Tester for Power
-
The Log4 USB is a circuit measurement tool which both display accurate readings of voltage, current, and power while also simultaneously logging all measurement data to a MicroSD card and/or the free dedicated PC software. The Log4 USB device is specifically designed to measure the low positive voltages of USB connected equipment with high accuracy.
-
-
Product
Phase Rotation Tester with Voltmeter
885 PR
-
Standard Electric Works Co., Ltd
● 3 functions in one unit: Phase Rotation, Phase Presence, Voltmeter● LCD contact type Phase Rotation Tester● Large LCD to show phase rotation and phase presence● Check a wide range of three phase power sources● Voltage range for phase rotation test: 75~600V AC ● Frequency range: 40~400Hz● 6000-count voltmeter● Auto ranging Voltmeter AC/DC● Data hold function● Auto power off● Convenient stand for viewing● Easy to use● Comply with EN 61010-1 CAT III 600V EN 61010-2-033 EN 61326-1
-
Product
Audio Impedance Testers
1106 IM
-
Standard Electric Works Co., Ltd
Large LCD : 68 × 34mm (2.677" × 1.338"). True measurement of speaker systems actural impedance at 1kHz. Three test ranges allow testing of home theater and commercial sound systems. Measures transformer impedances. Battery operation. Low battery indication. Data hold function. 0Ω adjustment.
-
Product
LED Tester
Iskra ST5-L
-
*Convenient one-hand operation*Ideal for Surface Mount Devices*Automatic LED polarity detection and display*Forward drop voltage display*Dedicated mode for testing bi-directional LEDs*Manual polarity preset modes*Adjustable constant test current 1-30mA*Adjustable test duty cycle 10-1000 mSec*LED visual brightness verification*LED visual color verification*OLED Display*Integrated Li-Ion battery
-
Product
Portable OTDR Tester
CARY-OT4000
-
The CA OPTRONICS CARY-OT4000 series portable optical time domain reflectometry (OTDR) is the latest FTTx optical fiber cable-based test instrument. It has light weight, elegant appearance, small size, easiness of installation and maintenance, high-capacity built-in battery. It provides multiple built-in test wavelengths and optical testing functions like visual fault locator (VFL). As a new product specially designed for FFTx network testing, it provides site technicians with the highest performance and upgrade services.
-
Product
FPD Tester Signal Module
A040209-05-04
-
A040209-05-04 is a MIPI signal module board and complies with the MIPI DSI v1.2 / MIPI D-PHY v1.1 signal specifications and standards. A040209-05-04 is used with the FPD Tester and can be applied to MIPI Display testing, providing MIPI Panel standard signal and other related controls.
-
-
Product
High-pressure environmental friction and wear tester
-
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy.
-
Product
E-DRIV® Brushless Electric Screwdrivers
NF-Series
-
Designed for high production environments, the E-DRIV® NF-Series feature a high performance brushless motor design that provides durability and reduces the common maintenance costs associated brush type electric screwdrivers. The NF tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management in power tools ensures product quality, cost savings and a reduction in overall ESD failures. The versatile assembly power tool is available in four different model configurations to meet the demand of various unique fastening applications.
