Sources
The origin.
-
Product
Analog Input Products
-
Analog input boards are useful for measuring variably changing conditions in the real world. When we want to measure these variably changing conditions, we need analog inputs to convert these changing real world conditions to changing electrical quantities. For example, monitoring the temperature inside a wood kiln, or the water pressure on the output of a pump, or the heart rate of a medical patient. In each of these cases, you can use one of our analog input devices to convert the electrical data from a sensor or transducer into binary data that can then be used by your computer. The device that converts this data is known as an analog to digital converter (abbreviated ADC, A/D, or A to D). An analog input is a measurable electrical signal with a defined range. The analog input changes continuously in a definable manner in relation to the measured property. This data is very useful for process monitoring, process control, or simple monitoring / data collection and acquisition. ACCES' analog input boards amplify and multiplex input signals from thermocouples, strain gauges, accelerometers, photo sensors, flowmeters, RTDs, thermistors, voltage sources, millivolt sources, and current sources, just to name a few.
-
Product
Paragon® 8.0 Slm NF3 Flow Intelligent Remote Plasma Source
-
For cleaning CVD and ALD/ALE process chambers, the Paragon remote plasma source is designed for high gas dissociation rates (> 98%) of NF3 with gas flows up to 8 slm and pressures up to 10 Torr. This leading-edge performance translates into increased process throughput and repeatable process results. The Paragon design incorporates a proprietary plasma block design with a Plasma Electrolytic Oxidation coating for low particle, long block life that delivers lower cost of ownership.
-
Product
Login Digital Epstein Tester Model
Model EP400
-
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Borehole Impulsive Source Of Choice
G-SOURCE
-
Over the years the Sercel G-SOURCE range of products has become the system of choice for advanced VSP surveys, in both offshore and onshore environments. The G-SOURCE and delta cluster combine the advantages of a powerful source and a clean acoustic performance to maximize borehole data quality.
-
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
HV High Voltage Detector
-
The Motwane Manufacturing Company
For decades, Motwane Voltage Detector has been a standard for international quality and safety ratings. Voltage detectors are used to signal the presence of voltage in a conductor since they make visible what we normally can’t see. Its application lies mainly in safety reasons during research, or when a service operation is under way. Most of the time, the monitored conductors come from low impedance sources whose voltage and energies are considered life-threatening.
-
Product
NTSC/PAL Color Bar Generator
CBG360
-
The CBG360 is designed to provide an accurate and affordable signal source for system testing. It also provides the necessary components for aligning color monitors to the proper brightness, color and hue.
-
Product
OTDR
OT700 series
-
Shanghai Tarluz Telecom Tech Co., LTD
SM OTDR, MM OTDR, visual fault locato), PON online test, Optical Power Meter, Optical Laser Source, Fiber Microscope, Ready for all kinds of environment.
-
Product
Mixed Injection System Liquid Vaporizer
MV-2000
-
The MV-2000 achieves stable vaporization, even at low temperatures, using the new tornado flow method. This is suitable for vaporization a range of liquids even challenging sources such as "High-k", a liquid source which is pyrolyzed easily.
-
Product
Anti Static Nozzles
-
is a high-performance ionization source, designed to simultaneously neutralize static charges and remove electrostatically bonded particulate from surfaces.
-
Product
Mode Locked Synthesizer
IT9200
-
The ITS-9200 is a synthesized RF source with a flexible locking capability that allows it to be phase-locked to non-standard external references. It is specifically designed for synchronization to mode-locked lasers with pulse output frequencies in the 72-80 MHz region, although it can be easily modified to adapt to other reference frequencies.
-
Product
Portable Test Systems
-
We refer to test meters with an integrated source as test systems. Test systems are particularly useful when you need custom current and voltage values when testing meter installations, but only want to use a single device.
-
Product
AINC 429 Multichannel Interface with Additional ARINC-717 Receive & Transmit Channels
DAS-429UNET/RT8-717
Interface Card
The DAS-429UNET/RT8-717 is an ARINC 429, multichannel interface card with additional ARINC-717 receive and transmit channels. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC 429 & ARINC-717 bus, both in the lab and in the field.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-429UNET/RT8-717 adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher).
-
Product
Impedance Analyzers
-
The E4990A Impedance Analyzer with a frequency range of 20 Hz to 120 MHz provides an industry best 0.045% (typ.) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source.
-
Product
RF Synthesizers Modules
-
Holzworth Instrumentation, Inc.
Holzworth's RF Synthesizers Modules were originally designed as the internal, tunable LO test sources for Holzworth phase noise analyzer products. Due to the need for easy integration, the HSM Series designs incorporate a long list of electrical and mechanical features to satisfy the demanding requirements of today's high performance communications systems and integrated test systems. FIELD PROVEN RELIABLITY with MTBFs exceeding 240kHrs.
-
-
Product
Spectral Single-Mode Diode Laser
-
The diode lasers are compact, single-mode light sources with a spectral width in the sub-MHz range (cw). A modulation input is optional. The wavelength for standard products is in the range 1530nm-1565nm (other wavelength can be tested).
-
Product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
-
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
-
Product
Broadband Coaxial Noise Sources
-
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
Product
Automation Monitor
-
The Automation Monitor is a diagnostic system for remote analysis and troubleshooting of semiconductor capital equipment. The monitor is capable of delivering synchronous streams from strategically located video cameras, sound devices and data sources on the equipment.
-
Product
Programmable DC Current Source
Model 121
-
The Model 121 programmable DC current source is a precision instrument suitable for bench-top use or panel-mounted operation in labs, test facilities, and manufacturing environments. It provides a low-noise, highly stable source of current up to 100 mA, with convenient manual selection through 13 pre-set output levels, each representing a ten-fold change in power when attached to a resistive load. A “user” setting allows the current output to be defined anywhere within the operating range of the unit, from 100 nA to 100 mA.
-
Product
RF Safety Monitoring
MVG EME Guard XS Radar
-
Specifically designed to alert workers operating near radar transmitters of RF exposures, the unique EME Guard XS Radar is an RF pulse measuring device. It continuously scans for short pulsed signals, and via its built-in alarm and visual system, alerts users whenever the acceptable limits have been exceeded. This RF Safety tool is extremely easy to use and creates a safer working environment close to radar antennas and other pulsed RF sources.
-
Product
Function Generators
-
PGP Electronics Private Limited
PGP Electronics Function Generators are a reliable source for different waveforms. Two units, function generator and frequency counter are integrated in to one unit. The built-in frequency counter can also be used to measure the external frequency.
-
Product
Magnetization related equipment
-
Shanghai Xianda Denshijiki Industry Co.,Ltd
The Magnetizing Device Is Also Called Magnetizer / Magnetizing Power Source. It Is Used When Magnetizing A Magnet In Combination With A Magnetizing Yoke And A Coil. Charging The Internal Capacitor From The Commercial Power Supply And Discharging The Energy To The Magnetizing Yoke Generates A High Magnetic field and magnetizes.
-
Product
Integrated Event Recorder
-
Wabtec’s integrated family of event recorders feature an FRA Crash Hardened Memory with capacities of 8 to 128GB permit storage of Event Data from a variety of locomotive sources, storage of PTC mandated data channels, and storage of up to four HiDef video cameras. In addition to crash hardened memory, units can provide removable solid state disk storage of video from panel.
-
Product
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
Programmable Bidirectional AC Laboratory Power Supplies (source / Sink)
-
Product
Calibrator, Calibrated w/Data, Current, 185 mm, 78 mm, 38 mm
72-6694 CAL D
-
The 72-6694 CAL D from Tenma is a current calibrator. It provides quality and accuracy of handheld calibrator of precision current source. It features large LCD display (maximum display counts 1999, 13mm (0.5") digit size). The current calibrator has 006P DC 9V, MN1604/PP3 battery or equivalent alkaline type or heavy duty type power supply. The dimension is 185mm × 78mm × 38mm (7.3" × 3" × 1.5") and weight is 265g/0.58lb (including battery). It has adjustable 0 to 24mA current source, 2 ranges (0 to 19.99mA (0.01mA display resolution, ±(0.25% FS + 1d) accuracy), 0 to 24mA (0.1mA display resolution, ±(0.5% FS + 1d) accuracy).
