Hall
a measurable transverse voltage which occurs when current flows through a conductor in a magnetic field.
-
Product
Photonic Hall Effect
HMS7000
-
Classic hall effect measurement system is to read voltage difference made between both diagonal sides, when flowing current and applying magnet field strength, in perpendicular to flowing current direction. - Photonic hall effect measurement is to read various electrical properties by illuminating light of “various range of wavelength” on the sample, in addition to flowing current and applying magnet field strength. - It is great to see “RGB (Red, Green, Blue), Light intensity vs carrier density, carrier mobility, resistivity, hall coefficient”
-
Product
Magnet Wheels Pulse Generators
199SM / 198EM Magnet Wheels
-
Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)
-
Product
Recirculating Chillers
-
Recirculating chillers from Lake Shore offer high performance for improved cooling capacity for your Hall measurement system, VSM, probe station, or electromagnet application.
-
Product
AC/DC Hall Effect Sensors
-
The PC clamps can measure currents from 10A to 7500A* on conductors with a maximum diameter of 80mm (100x64mm and 122x54mm). They are available either with an internal battery or in versions which require an external battery or a dc power supply.
-
Product
Hall probes
-
Axial, transverse, multi-axis, and tangential Hall probes for measuring magnetic flux density. Choose from a wide range of lengths and thicknesses—probes are also available for cryogenic applications.
-
Product
Vehicle Actuator Tester
7651
-
Peaceful Thriving Enterprise Co Ltd
This device is design to test electronic components actuate by magnetic field or electronic magnetic field. Devices like actuator, ignition coil, AC generator, indoor air blower, valve controller EGR (exhaust gas control), injector, spark plug, relay and hall effect sensor can be tested.
-
-
Product
Speed Sensors
-
Variohm supply differential hall effect speed sensors for use in motorsport applications. We have two different designs but both offer very high performance.
-
Product
Reference Magnets
-
Reference Magnets provide a stable and convenient method to verify the accuracy and calibration of Hall Effect Gaussmeters, Teslameters, and Probes.
-
Product
Magnetic Speed Sensors
-
We offer the most comprehensive portfolio of magnetic speed sensors ICs, covering the full range of speed and speed with direction, two- and three-wire interface, magnetic encoder (ring magnet) and gear tooth sensing, Hall and GMR technology, and ASIL-compliant options for transmission, wheel speed, engine, e-motors, and many more encoder and gear tooth sensing applications.
-
Product
Hall Sensor Board with I2C Interface
055-013
-
Version: +5V/5A +3,3V/5A +12V/5A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Non-contacting Position Sensors
-
For use in harsh environments, Vishay offers non-contacting position sensors based on Hall Effect technology. Linear displacement, rotational (single- and multi-turn), and kit design options all provide a full 360° measurement range with no dead angles and very long life, since there is no wear and tear on sensor elements. Applications for Vishay’s non-contacting position sensors include any system where vibration, shock, or dithering is to be expected, such as embedded applications in vehicles.
-
Product
Gaussmeter
DX-101
-
DX-101 Gaussmeter is based on the Hall effect magnetic field strength of the latest developments in instrumentation, the design of desktop-type Gauss meter. Maximum range 330.0mT and 3000mT two tranches, the minimum basic error of 1.0%. Test probe connectors is imported, stable and reliable connection.
-
Product
C Series Frequency Input Module
-
The C Series Frequency Input Module is designed to acquire isolated frequency inputs from magnetic pickup sensors, variable reluctance sensors, Hall effect sensors, and other transducers with a frequency output. Additionally, the C Series Frequency Input Module provides isolation, configurable thresholds, selectable filtering, and embedded counter measurement logic. These measurements can be synchronized with other frequency, analog, digital, and counter measurements in a single acquisition.
-
Product
Current Sensors
-
Measurlogic offers an array of current sensors for every need, including split core, solid core and Rope current transformers (CTs); DC Shunts and Hall Effect Sensors. All of our electrical sensors are designed with an easy, un-intrusive installation in mind. With a low cost and high accuracy guarantee, we provide top of the line solutions for measurement and cost savings for residents and business owners alike.
-
Product
Magnetic Field Sensors
-
Analog Devices magnetic field sensors combine integrated bulk Hall cell technology and instrumentation circuitry to minimize temperature related drifts associated with silicon Hall cell characteristics. The architecture maximizes the advantages of a monolithic implementation while allowing sufficient versatility to meet varied application requirements with a minimum number of components.
-
Product
Current Probe For Non-Intrusive Measurement Of AC, DC, And Waveform Currents
CP 305
-
The CP 305 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.Using advanced Hall Effect technology the CP 305 can measure currents accurately up to 450A peak over the frequency range of DC to 20 kHz.
-
Product
Zero Field Cavity
-
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
CAN Controller
MS 1529
-
- The "CAN" Bus Interface for Hall Controllers and Car controller- On-board EEPROM and KEY inputs for user settings parameters- LCD Module Interface- Eight 110 VDC Opto input interface- Six inputs interface (TINS, TUIB, TDIB, FIRE, FP, PRO-SW)- RS485 Interface and RS232 Interface (Optional)- Real time clock for Time Information
-
Product
Hall Sensor Board with I2C Interface
048-368
-
Version: +5V/60A +5V/60A +3,3V/25A +12V/25A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Hall Effect Measurement system
HMS-5300
-
Variable temp : 80K ~ 350K (model#: AMP55T ) - HMS-5300 can be compatibly used with both low temp magnet kit (model# : AMP55T) and high temp magnet kit (model# : AHT55T3, upto 300dC). - Below image is to show model# HMS-5300 + AMP55T, for low temp.
-
Product
Hall Sensor Board with I2C Interface
050-382
-
Version: +5V/15A +12V/15A -5V/15A -12V/15A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Guarded Insert For PPMS®
-
The Lake Shore guarded insert can be used alone or with one of our PPMS Hall measurement packages that include the MeasureReady® M91 FastHall controller. Cut your measurement time up to one-half with the M91. Measurements are so fast that time-dependent misalignment errors are eliminated using the patented FastHall™ measurement technique.
-
Product
Helmholtz Coil
-
In the measurement of magnetic fields by means of Hall probes or measuring coils it is necessary to calibrate the instruments in a known magnetic field. Our standard field coil according to Helmholtzenables to production of a magnetic field calculable with high accuracy from the dimensions and the amperage. In series arrangement with an accurate ammeter field strengths of up to 800A/cm are produced. The dield room accessible both in axial and radial direction. Helmholtz coils with fluxmeters are also useful in testing of magnets. Helmholtz coils give repeatable results as against the search coils due to which the magnets can be compared with more accuracy for their total flux and in turn their quality. Field Generating and Field Detecting Helmholtz coils are designed as per user specifications.
-
Product
Position Sensors
-
Position sensor is a device that can detect the movement of an object and converts these into signals suitable for processing, transmission, or control. TE Connectivity (TE) is a leading manufacturer of industrial linear and angular position, tilt and fluid level sensors. Both off -the-shelf and custom position sensing solutions are available featuring our core technologies, including inductive, potentiometric, magnetoresistive, hall effect, reed switch, electrolytic and capacitive sensing.
-
Product
4-20mA Converters
4026
-
SPECTEC Innovative Sensor Solutions
Model 4026 Freq to Voltage or Freq to Current Converter accepts frequency input from any magnetic speed sensor, digital magnetic pickup or Hall effect zero speed sensors. Input and output configurations are field selectable. Input range is adjustable between 1100 Hz - 10 kHz or 75Hz to 1100 Hz. Output selection can be configured as 4-20mA converter, 10-50mA converter, 0-5 V FTV converter or 0-10 V FTV converter. ZERO and SPAN adjustments easily calibrate to almost any measurement range, with little interaction between the adjustments.
-
Product
Hall-Sensor Board with analog output
041-970
-
The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
Electromagnets
-
The Lake Shore electromagnets (EM-V Series) produce magnetic fields with a variety of indexed air gap and pole cap configurations. The EM-V Series is ideally suited for integration into customer-designed magnetic test platforms for applications including magneto-optical studies, magnetic hysteresis studies, in-line annealing, Hall effect studies, susceptibility measurements, spin magnetic resonance demonstrations, and biological studies.
-
Product
ARM Elevator Board
MS 1517
-
- Works with 2 wires, supplied with landing displays and communication with "CAN" processor- Provides field-proven perfomance, lifetime support commitment.- Remote communication with modem and suitable software enables user to download the system history from remote location- Monitor and control elevators inn real time-across campus or country.- Group Control Available upto 64floors and 6 cars.- Displays car and hall calls, waiting times and Data Log Information on a color screen.- Stores information during the working day.- Self learning call allocation, allows system to read day by day call history and respond to the unexpected travel patterns from previous experience
