Bipolar Power
smooths transition between negative and postive precision DC voltage at any amount.
See Also: DC Power Supplies
-
product
DC Laboratory Power Supplies
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for teaching aids, schools and universities and offers safe use but also a very good price / performance ratio.
-
product
Assembly and Testing of Power Steering Motors
Interlinked stations for assembly and testing of servo-electric steering drives*Station 1: Force / path monitored*Station 2: Verification of the software version, with variant-dependent parameterization*Station 3: Leak test as vacuum test as the overpressure test*Station 4: Function and noise testing and order analysis
-
product
Wind Power Solution
EVO ACCIONA
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
product
SCR Controlled DC power Supplies
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
product
Universal AC-DC Power Supplies
PS-RS50-5
WINSYSTEMS’ PS-RS50-5 is a small, convection cooled 50W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 10A of current at +5 volts. The +5 volt output can be adjusted with an on board trimpot. The PS-RS50-5 is small, measuring only 99 x 97 x 36mm.
-
product
Regenerative Power System, 20 V, ±400 A, 5 KW, 400/480 VAC
RP7941A
The Keysight RP7941A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
product
High-density Power Drivers
Gate drivers, FETs and protection circuitry integrated into a single package to drive loads in industrial and home-appliance applications, with increased power density per cm². ST’s high-density power drivers are System in Package (SiP) solutions integrating in compact QFN packages the STDRIVE gate drivers and MOSFET-based power stages, responding to the industrial market trend towards higher levels of integration and lower development costs.
-
product
RF Power Meters
Peak Power Analyzer has been totally redesigned from the inside out. This meter is taking performance to a new peak and changing the way the industry views and analyzes RF data.
-
product
Power Supply 600W
UEP10M66 / CEP10M66 -
The UEP10M66 series is a linear regulated plug-in power supply for use in CERN type NIM and CAMAC crates with 600W power output for applications with extreme +/-12V loads. This high precision and lowest noise power supply is designed as a very compact unit with extremely low volume to power relation.
-
product
Flight Deck Power Systems
Multiple EmPower products are already a standard linefit option on Boeing and Airbus. Astronics flight deck power systems are modular in design and available in 110VAC, high power USB (10W), and the latest USB power delivery technology - USB Type-C (60W).
-
-
product
High Powered External IP Transmitter
PowerSting
The PowerSting is a series of external high power transmitters (5kW, 10kW, and 15kW) for the SuperSting R8/IP/SP and SuperSting R1/IP/SP. The PowerSting system is a fully programmable constant voltage//constant current source. The PowerSting system comes with an SGS generator and a wireless repeater box, and operates in both wired and wireless modes. The applications of the PowerSting-SuperSting system include vertical electrical sounding, 2D electrical imaging, 3D electrical imaging, 3D offset electrical imaging of a 2D survey line in both manual and automatic modes.
-
product
PXI 6U Power Relay Module
The SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC. The module is built on a single width 6U PXI module and the interface is via a standard PXI/CompactPCI backplane. Connection to the switching contacts is via three 50-pin D-type male connectors mounted on the front panel. These are machined contact types with 7.5A current carrying capacity.
-
product
10-amp AC and DC Variable Power Supply
ACDC-10
The ETI Model ACDC-10 is a small, lightweight, and portable AC and DC power supply. The unit is intended for resetting circuit breaker charging motors and other general-purpose applications. It will provide DC voltage in three nominal ranges from 0-120V, 240V, and 480V at 1 kVA, as well as AC voltage in three nominal ranges from 0-140V, 280V, and 560V at 1.4 kVA. The ACDC-10 is housed in a rugged plastic enclosure approximately 20” x 11” x 18” and weighs less than 65 lbs
-
product
Economic Extreme Power Temperature Forcing System
ECO Cool
ECO Cool® Economical Powerful - Thermal Forcing System.Exceptionally Powerful, Economical & Reliable
-
product
Power supplies
TES Electrical Electronic Corp.
Over-Voltage, Over-Current protection.Built-in buzzer alarmEasy recall and store functions
-
product
Laser Power Meters
Laser Power meters are a vital tool in your Preventative Maintenance regime.They allow you to quickly test the the performance of your optical system (laser source / mirrors / lens) and pin point any potential issues before they can affect your product quality and production throughput.Power meters are great for determining if specific components are starting to deteriorate, allowing you to order and replace without impacting too seriously on your production.The power meter measures the laser output for the following laser sources and wavelengths:CO2 Glass DC Laser Tube / 8~11 microns or 8,000 ~ 11,000 nm wavelengthCO2 RF Metal or Ceramic Laser / 8~11 microns or 8,000 ~ 11,000 nm wavelengthYAG Laser / 900 ~ 1250nm wavelengthFiber Laser / 900 ~ 1250nm wavelength
-
product
PXI Power Relay Module, 10xSPST, 16 A
40-161A-003
The 40/42-161A-003 is a PXI/PXIe 10xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
product
12V Automobile Power Supply
7500A
Peaceful Thriving Enterprise Co Ltd
This is 12V automobile power supply. Avoid the loss of memory during the vehicle's battery replacement.
-
product
High Power DC Electronic Loads
63200A
Chroma Systems Solutions, Inc.
Chroma High Power DC Electronic Loads provide wider operating voltage and current ranges up to 240kW, sine wave loading, dynamic frequency sweep to 50kHz, digitizing, MPPT, an impressive front panel that tilts, and the highest accuracy available (voltage 0.015% + 0.015% F.S. and current 0.04% + 0.04% F.S.) – all with an incredibly high power density (6kW @4U).
-
product
Fiber Optic Power Meter
The handheld Fiber Optic Power Meter is a user-friendly tool for engineers testing and maintaining fiber optic systems & networks. Both compact and rugged, these devices can be used for absolute optical power measurements, as well as relative loss measurements. In addition, high accuracy and a user self-calibration function result in an excellent overall value.
-
product
Power Meter
TW3203R
Techwin(China) Industry Co., Ltd
TW3203R handheld optical power meter is the oldest portable test instrment in the Techwin power meter series. It features compact size, ease-of-use and economy advantages. It can be used for absolute optical power measurements as well as for relative loss measurements of optical fibers. TW3203R is an essential test instrument in Optical Communications, CATV and other Fiber Optic measurements.
-
product
3-Pin Power D-Type Connector & Cable Accessories
Our 3-Pin D-Type connector is used on PXI switching products to provide a low density user connector solution.
-
-
product
Regulated DC Power Supply
PDS-A Series Hybrid
As compared with dropper-method DC power supplies, the unique switching and dropper circuit systems bring low output noise at same level, light weight less than half, and compact body. PDS-A power supply corresponds to EU RoHS regulation in consideration of environment. GP-IB, RS-232C, USB and LAN optional control boards are available and users are able to download API and drivers software from TEXIO web-site.
-
product
Load Cell Power Supply Module
MODEL PSM-F10
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
product
Powered NIM Crates
NIM CERN-CE 1920W With Fan Tray
This CERN spec./CE NIM crate series represents modular designed NIM bins combined with high power /low noise, microprocessor controlled, switching mode power supplies in excellent and proven W-IE-NE-R quality, conforming to EUR4100 and CERN specifications. For ultimate requirements the NIM crate provides up to 1920W DC power and is outfitted with a fan tray for cooling, monitoring and control.
-
product
AC Power Sources
Asterion AC
AMETEK Programmable Power, Inc.
Inspired by the enduring power of a brilliant star, the California Instruments "Asterion" line of AC power sources by AMETEK Programmable Power combines intelligence and flexibility to create an advanced platform of AC solutions. This easy-to-configure design features sophisticated technology for delivering high performance, programmable AC and DC power. Its sleek design packs maximum power density into a low-profile form factor with an intuitive touch screen interface placing that power at your fingertips. Centralized control and unparalleled modularity make Asterion the most adaptable platform on the market. Its groundbreaking capabilities set the standard for affordable, precision power sources.
-
product
MTM-PM-1: 1-Channel DC Power Module
EXCELS AT POWER: The MTM-PM11 1: Channel DC Power Module excels at powering devices that need stable power under large transient loads during manufacturing and R&D testing. Optimized for devices using LiPo or similar batteries. Accurate voltage, temperature and current measurements can be made through the powerful and cross-platform BrainStem API.
-
product
AC Power Source
61600 Series
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
