Inspection Systems
See Also: Inspection, Inspection Services, X-ray Inspection Systems, Automated Fiber Optical inspection Systems
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
Complete Non-Contact Inspection System For OLED/TFT/LTPS
GX3/GX7
-
*Fastest*Workable to large panel as well as fine pattern of medium-small panel*Workable to large mother glass of every generation*Possible to dock width Repair Machine
-
Product
Surface Defect Inspection System
-
Wafer for inspection of surface condition of specular flat substrate, glass substrate, others φ 100 ~ φ 300 compatible
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
Optical Inspection System
OIS Products
-
A manual optical inspection system that is able to inspect the wire-bonded leadframe or substrate.
-
Product
Desktop Inspection/Measurement Systems VisionGauge Digital Optical Comparators
400 Series
-
The 400 Series VisionGauge Digital Optical Comparator are state-of-the-art inspection and measurement systems in a compact desktop format. It''''''''s a compact desktop system that still provides a large working envelope. The 400 Series is a very cost-effective, full-featured system that has all of the advanced, patented VisionGauge software capabilities. This system is especially well suited for lower volume applications.Available in both Horizontal and Vertical Configurations. Patented VisionGauge CAD Auto-Align and CAD Auto-Pass/Fail tools provide fast, accurate and operator-independent results. 3 axis inspection and measurement system with manual stage movements
-
Product
Power Transmission Line Inspection System
-
Shandong Senter Electronic Co., Ltd
With the aid of high-end technology and equipment, Senter Electronic manufactures and trades high-tech power transmission line inspection system with low price. And we are known as one of the leading such manufacturers and suppliers in China for our quality products and good service. Welcome to buy the power transmission line inspection system with our factory.
-
Product
Wafer Internal Inspection System
INSPECTRA® IR Series
-
An infrared internal defect inspection system has been added to the INSPECTRA® series.It is now possible to inspection with both infrared and visual light in one system.
-
-
Product
COTS Systems
-
Pre-integrated to save you time and money, pre-validated systems proved an optimum computing platform for mission applications.
-
Product
Real-Time Operational and Situational Awareness for IoT Systems
Vortex Insight
-
Vortex Insight is a web-based tool that can be used to monitor and manage a Vortex-based system from any location and on any device. It provides views of a Vortex system including statistics associated with DDS entities and system elements active in a live environment. It also provides configurable dashboards for monitoring system behavior through graphs and charts of statistics, including resource usage. Vortex Insight allows users to control the configuration and the QoS of Vortex applications, services and systems.
-
Product
4U 8-Slot CompactPCI® System with Redundant Power Supplies
cPCIS-6418U
-
The cPCIS-6418U Series Subsystem is designed for maximum density and has 8 horizontal slots for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
Vision Systems
-
Embedded vision systems, also referred to as compact vision systems, offer an alternative to Smart cameras and computer-based systems. The ADLINK EOS series is a complete embedded system that offers image acquisition, processing, archiving, and display capabilities. It is equipped with a multi-core CPU, ideal for applications requiring high computing power and multi-camera imaging, such as 3D vision and robotics guidance. Featuring rich I/O connectivity with factory-floor networks, including RS-232/422/485, USB, and isolated digital I/O, as well as onboard storage, ADLINK’s embedded vision system is ready to deploy. A system monitoring feature, feeding back temperature and voltage data, combines with a watchdog timer to maximize robustness and reliability of the ADLINK EOS series in mission critical applications.
-
Product
LabVIEW Professional Development System
-
ntegrate hardware from a variety of measurement instruments and devicesIntuitive graphical programming syntax to simplify automationBuild custom user interfaces for engineering applicationsBuilt-in algorithms for signal processing, analysis, math, and PID controlSoftware engineering tools to debug, validate, and deploy codeOne-year SSP membership for technical support, online training, and software upgrades
-
Product
Seat Actuation Systems
-
Extensive solutions for seating cabin interiors including motion and lighting controllers, linear and rotary actuators, power supplies, passenger interfaces, custom harnesses, sensors, pneumatic units, and bladders.
-
Product
Aircraft Data Systems
-
Aircraft data systems for commercial and military applications, including Aircraft Interface Devices (AID), avionics I/O computers, avionics test & simulation interfaces, and Embedded avionics interfaces.
-
Product
Tool, Inspection Depth Gauge, Mini Coax, ITA
910121157
-
Used to verify the depth setting of the center conductor of the ITA mini coax contacts.
-
Product
Mezzanine System
3560
-
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
LabVIEW Development Systems
-
Base--The instant productivity of graphical development for DAQ and instrument controlFull--A rich set of routines for mathematics, signal processing, and signal generationProfessional--The solution for professional developers who need code deployment or validationLabVIEW suites--LabVIEW Professional plus industry-specific add-on software
-
Product
Mezzanine System
5181 MMS ECM
-
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
Product
Source / Measure Unit (SMU) Modules, N6700 Power System
-
The Keysight N6780 family of source/measure units (SMUs) provide advanced features and precise control and measurements of voltage and current down to the microampere and nanoampere regions. They provide stable, glitch-free output voltage and current during high-speed load changes, fast output modulation, and high-speed measurements of both voltage and current simultaneous.
-
Product
IFEC Embedded System Hardware
-
State-of-the-art system components serve as building blocks for you to create the ideal IFEC system.
-
Product
Validation System
FLEX BMS
-
The FLEX BMS™ Validation System is a quick-connecting, highly flexible test system for rapid evaluation of centralized, single-board and distributed battery management systems. Utilizing Bloomy’s industry-leading battery cell simulators, COTS instrumentation, industry-standard connectors, and models that run in real-time, the FLEX BMS™ Validation System can easily be reconfigured to test a wide variety of BMSs. The FLEX BMS™ Validation System is used by national and regional safety and standards labs for certifying the BMS for a wide array of e-mobility products and applications.
-
Product
High-Speed Signal Recording Systems
-
GaGe has a long history of providing high-speed, real-time signal acquisition, processing, and recording systems on PC-based platforms. This expertise saves customers time and eliminates uncertainties and risks with self-integrated systems.
-
Product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
-
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
-
Product
VIP IFEC & CMS Systems
-
Astronics is the smart choice for inflight connectivity, entertainment, and cabin management solutions for VIP, VVIP, and business aircraft. From the highest-performing global SATCOM connectivity for optimum productivity and entertainment, to our Avenir IFE/CMS line that incorporates the latest technologies to deliver native 4K video distribution through the highest bandwidth Ethernet network system in the industry, Astronics is ready with a cutting-edge solution that delivers the ultimate VIP experience.
-
Product
Photonics Module Test System
58625
-
Chroma 58625 provides characterization testing for 3D sensing illumination devices. various test modules are combined for validation testing under precise temperature control.
-
Product
Radio Frequency, Communications, & Navigation Test Systems
-
Reduce testing time and costs with the Astronics radio test sets for use in military, avionics, and civil security industries.Available in commercial and military grades, these integrated test systems make it easy to develop test program sets and leverage them securely and instantly across all deployed testers at the factory, depot, and operational levels.
-
Product
6U VPX Direct RF Processing System
VP460
-
The VP460 is designed to enable customers to begin development of their next generation systems using revolutionary new processor technology. It is in alignment with the SOSA™ Technical Standard to provide the interoperability required by the US Air Force, Army and Navy.
-
Product
Enclosed Fanless Industrial Embedded Computer with NXP® i.MX8M Application Processor
SYS-444Q
-
The SYS-444Q is a rugged enclosed fanless embedded computer system with NXP’s i.MX8M industrial application processor with quad-core Arm Cortex®-A53 for low-power processing. This rugged system has dual Ethernet, industrial I/O, expansion options, TPM 2.0 hardware security, and options for wireless connectivity. The processor supports industry-leading video processing along with an M4 microcontroller for real-time subsystems making it an ideal fit for industrial IoT applications requiring highly reliable performance in harsh conditions such as digital signage, industrial automation, energy management, building automation, and others.
