-
Product
Bidirectional Programmable DC Power Supply
IT6000C Series
-
The bi-directional programmable DC power supply of IT6000C series combines two devices in one: a power supply (source) and an electronic load (sink) with energy recovery. Based on these two functions, IT6000C offers the functionality of two-quadrant operation. The regenerative capability enables the energy consumed to be put back onto the grid cleanly, saving costs from energy consumption and cooling, while not interfering with the grid.
-
Product
16 DI/O IP67 Machine Mount M12 PROFINET/Modbus IoT Ethernet Remote I/O
ADAM-250PN
-
16-ch configurable DIO and 2-port power/ethernet daisy chainIEC 61131-2 type 3 sink DI and fast response source DOSupport I/O and power diagnostic and DO safety value protection functionsPrintable marking label & LED indicator monitoring system/network/diagnostic/power statusEnables cabinet-free front and side wall & machine mountingCompatible with M12 Screw lock and Push-pull fast-lockingRugged IP67 design resists EMC, vibration, dust, oil, and humidity from harsh/outdoorBuilt in Sensor/Actuator/Encoder Power Supply from each I/O portSupports PROFINET and Modbus/TCP, with extensible design for MQTT integration
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
High Voltage DC Power Supply
IT6700H Series
-
IT6700H series high-voltage DC power supplies is with maximum output power 3000W, adjustable voltage 0-1200V and current 0-10A, IT6700H series have desktop and shelves installation function, easy to operate. IT6700H series provide list mode, built-in RS232 / USB / GPIB communication interface, rich SCPI instructions facilitate the formation of a variety of intelligent test platforms.
-
Product
6-Port Hardened Industrial Gigabit Ultra PoE DIN-Rail Switch
TI-UPG62
-
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
Product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
72-8690A
-
The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.
-
Product
6-slot ShoeBox Chassis
AX60530
-
*Compact design for embedded applications*Supports half-size SBCs*Exposed one slim CD-ROM & one 3.5" HDD drive bay; internal one 3.5" HDD drive bay*Equipped with ATX 200W power supply*Easy-removable cooling fan
-
Product
DC Turbo Power Supplies
RKT Series
-
RKT series power supply is programmable DC power supply with distinctive turbo function which realises 4-5 times wider coverage of output voltage and current in comparison to conventional DC power supply of equivalent output power.You can apply to wide usage with only one unit but no need to apply power supplies with extra margin for output voltage and current because each unit can output voltage and current flexibly within the range of 400W, 800W and 1600W.
-
Product
Gyro Test Panel
TA-256
-
Designed to test the KI256 / KI258 panel mounted Flight Director gyros. The panel contains a power supply, the special manufacturers recommended rate board required by SA-103 to properly verify outputs As well as all other electronics required to support by the book testing.
-
Product
Medical Box PC Featuring The 12th/13th/14th Gen Intel® Core™ I3/i5/i7/i9 Processors, With Support For MXM-AXe Based On Intel® Arc™ GPU, And Thunderbolt™ 4 Port
MLB-3102 with Intel MXM GPU
Industrial Computer
- ADLINK MXM-AXe graphics module support (type A, up to 50W TDP based on power supply)- 12th/13th/14th Gen Intel® Core™ i3/i5/i7/i9, Celeron® processor- Dual SODIMM for up to 64GB DDR5 non-ECC memory (depending on CPU)- 1x HDMI 2.0, 5x DisplayPort (1 from CPU, 4 from MXM)- 1x M.2 E-key supporting 1630 or 2230 for Wi-Fi/Bluetooth module, 1x M.2 M-key supporting 2242 or 2280 for SATA/PCIe storage module, 1x M.2 M-key supporting 2242 or 2280 for NVMe & frame grabber- Reliable Molex 24V DC-in connector- 2x 2.5GbE Intel® I225-LM Ethernet Controller- 2x PCIe Gen 3 x4 expansion slot for full-height, half-length add-on card, each slot is 25W power budget and additional Molex 4-pin power cable (12V/1.5A and 5V/2A) support
-
Product
Magnetic Particle Flaw Detector
MT-1B
-
MT-1B magnetic particle flaw detector adapts high-capacity lithium battery pack, converse DC to AC through variable-frequency, providing magnetic powder flaw detector with magnetic power supply. With low power consumption, it can continuous work more than four hour after charging. It especially suits for working in the wild and aerial area.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Stationary Industrial And Railway Power Supply
-
For decades, Gustav Klein has been supplying safe power supplies for industry and railways, such as rectifiers, inverters, DC converters, UPS and BSV systems, as well as frequency converters with a fixed output frequency.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
200 MHz, 3.5 pF, 1 MOhm Active Differential probe
ZD200
-
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Product
2U Wall-Mount/Tower Embedded Mini-ITX Chassis With One Dual Expansion Slot
RK-200I
Chassis
- Supports one dual slot expansion card(Low Profile)- Reserved for 2 USB, 2 COM, and 2 antenna punchouts.- One 3.5” drive bay and one 2.5’’ drive bay. (Compatible for three 2.5’’ drive bays)- 8cm two ball bearing PWM fan ( 42.5 CFM)- Support both Flex ATX power supply & AC-DC power adaptor
-
Product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
Regenerative Power System, 950 V, 20 A, 10 kW, 200/208 VAC
RP7953A
DC Power Supply
The RP7953A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test. The regenerative capability enables the energy normally consumed to be returned to the grid cleanly, saving costs associated with energy consumption and cooling.
-
Product
Diode Lasers
6-Watt Blue Engraving Laser
-
Advanced Photonic Sciences LLC
Can be used in laser engraving, marking, and cutting applications. Process wood, plastics, metals, anodized aluminum, stone, tile, and other materials. The adjustable spot can be adapted to the needed distance from laser to the material. The spot, with a size of <100 μm, creates very fine engravings and sharp cutting edges. The built-in driver accepts TTL and analog signals for power adjustments. The laser can be controlled between 0% and 100% of output power. It comes preset and needs only a power supply and a signal source.
-
Product
75-Watt AC/DC Power Supply; Triple Output
56KT1
Programmable Power Supply
NAI’s 56KT1 is a 75 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, triple output, at a baseplate temperature of +85° C.
-
Product
Autoranging System DC Power Supply, 80 V, 170 A, 5000 W, 400 VAC
N8940A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
1 PICMG® CPU, 1 PCI-E® x16, 3 PCI-E® x4, 7 PCI™ Slots Backplane
EBP-13E4
Backplane
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 3 PCI-E® x4, 7 PCI™- Support ATX power supplies- Dimension: 330 mm x 318 mm
-
Product
Active Differential Probe
DF-600
-
The DF-600 Differential Active Probe is a high input impedance and low input capacitance probe. It also supports extremely high frequency bandwidth, and high voltage input. It is designed using three OP amps, namely two FET buffer OP amps and a low offset OP amp. Therefore, even with long-term operations, the measured voltage will not drift. The voltage offset always approach 0 volts. (USB power supply should be 5V ±2%). The following diagram shows the circuit of DF-600.
-
Product
Solar Array Simulator
62000H-S series
Simulator
The latest programmable solar array simulator power supply 62000H-S Series released by Chroma provide simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000H-S provides an industry leading power density in a small 3U high package. The solar array simulator is highly stable and has a fast transient response design, which are both advantageous to MPPT performance evaluation on PV inverter devices. The 62000H-S Series have many unique advantages including high speed & precision digitizing measurement circuits with a 100kHz A/D, 25kHz D/A controlled I-V curve and a digital filter mechanism. It can simulate an I-V curve accurately and response the mains ripple effect from the PV inverter. In addition, the built-in EN50530/Sandia SAS I-V model in the standalone unit can easily program the Voc, Isc, Vmp, and Imp parameters for I-V curve simulation, without a PC controller.
-
Product
Switching DC Power Supply
-
Has pure DC output and low ripple and noise, making it an excellent choice for schools, aging testing of rechargeable batteries and electronic products.
-
Product
DC/DC Power Supplies
-
Astrodyne TDI’s line of DC/DC power solutions provide both a high performance and cost effective power conversion solutions for a variety of applications where efficient distributed power is required. The Astrodyne TDI team can help you find a solution that meets your specific requirements
-
Product
Power Supply and Current Monitor
DC Connect
-
DC Connect enables measurement of current consumption of battery operated and other low voltage devices such as hearing aids
-
Product
Power Quality Analyzers
APQM-702/APQM-703
-
It can be powered from the L phase.It is intended for use in virtually all types of networks from 64 V to 760 V directly, with special consideration for measurements on low-voltage poles, due to its ease of connection.It has an independent power supply and is therefore particularly suitable for measurements outside of voltage transformers. It can also be adapted for measurements on DC voltage systems.Real-time remote configuration and data transfer (GPRS) using a built-in GSM modem
-
Product
4U Rackmount Barebone PCs
-
ACP-4000 rackmount GPU IPC feature high wattage power supply & great heat dissipation efficiency, providing the robust base for edge AI applications.
-
Product
CZT Gamma-Ray Detector Spectrometer
GR Family
-
The Kromek GR family is a range of CZT-based high-performance gamma-ray spectrometers. They are completely self-contained, with built-in preamplifier, shaping amplifier, baseline restorer, pulse height digitizer, and HV supply. The digitized pulse heights of detected gamma-ray signals are sent to a PC via the USB. The unit is powered entirely from the USB bus, so no external power supply is needed.
