-
Product
Voyager Intermittent Fault Detector
-
The Voyager includes a spread spectrum TDR so that the fault can be located. Once an intermittent is detected, the TDR is immediately connected to the failed test point and used to determine the distance to the fault.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
Fault Insertion Unit
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
-
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
Product
Service Drop Locator
VM-560
-
The VM-560 is a general-purpose locator used to detect buried pipe and cable services in a variety of situations. With a 50/60Hz passive power locating frequency and three active frequencies, the VM-560 locator will meet the requirements of those wishing to detect the presence of active power cables and to trace short ranges. The VM-560 transmitter also has the additional frequency of 8kHz Fault-find so it can be used to detect the presence of ground to sheath faults on cable when used with the VM-510 Stand Alone A-Frame fault locator.
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
Switch Module
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Digital Earth Tester
-
Cambridge Instruments & Engineering Co.
'CIE' Digital Earth Resistance Tester is designed to measure the resistance if earth used in power circuit, Telecommunications, Railway Electrification, Domestic and Industrial electrical installations. The tester measures directly the resistance of the earth and also measure the ground resistivity.
-
Product
Fault Location
-
They can occur when new, during commissioning of the cables or initial energization, or many years after the cables have been put into service. The types of faults can also vary considerably, from dead shorts (also sometimes called “bolted faults”) to a cable that has catastrophically faulted and completely blown open.
-
Product
5mA High Accuracy Ground Fault Detector
HA-GFD
-
Our HA-GFD Current Probe is our most sensitive current probe, measuring down to 5 milliamps. Ideal for measuring leakage current and ground faults. Dual range allows measuring up to 200 amps in high accuracy.
-
Product
Service Drop Locator & Metal Detector
VM-585
-
The VM-585 is a combination of the popular VM-550 utility locator with the added benefit of a built in Ferrous Metal Detector. This makes it ideal for locating short distance runs such as service drops and to detect buried ferrous metal objects such as buried valve box covers, buried tanks, and manhole covers. The advanced filtering of the VM-585‘s metal detector rejects materials such as bottle caps and aluminum cans and zeros in on finding only ferrous materials. The manual gain control allows it to be controlled and able to work close to large metal objects such as automobiles and chain link fences while still looking for the targets underground. The VM-585 will locate through asphalt, concrete, or grass and in temporary conditions such as snow.
-
Product
Water Pipe Locator & Leak Detector
RD510
-
Water leakage is a major global challenge. Water pipe leaks lead to substantial water loss, increased operational costs, and undermine efforts to ensure sustainable water management and supply.
-
Product
Faster fault diagnosis
Rx Series
-
Based on the award-winning PHABRIX Sx handheld test & measurement range, the rack-mounted Rx series delivers advanced 2K/3G/HD/SD signal generation, analysis and monitoring for faster compliance testing and fault diagnosis of video and audio. Video capture speeds intermittent fault finding, and remote access offers monitoring from any location.
-
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A, Hardware Interlock
40-192A-012-HI
Fault Insertion Unit
The 40-192A-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test:
-
Product
Earth Resistance Tester
2678
-
Shenzhen Chuangxin Instruments Co., Ltd.
RK2678 series Earth Resistance Tester is used to measure the grounding resistance of the electrical equipments’ internal. It’s suitable for measuring the ground wire resistance of the various motors, electrical appliances, instruments and meters, household appliances and other equipment enclosure etc.
-
Product
Earth Resistance & Resistivity Meter
MRU-200
-
MRU-200 is the only meter in the market which uses all measurement methods.Possible measurements:- earth resistance measurment with 2-pole, 3-pole,4-pole method,- impulse earth resistance measurement, two kinds of measuring impulse 4/10s, 10/350s,- earth resistance measurement without disconnecting measured earths (using clamp),
-
Product
PXI Fault Insertion / Signal Insertion Switch Modules
Switch Module
Pickering's PXI Fault Insertion / Signal Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system. Two switching topologies are available: *Single signal paths with series switches and switches to connect to one or more fault buses*Pairs of signals with series switches, shorting switches between the signal pairs and switches to connect either signal to an external fault input.
-
Product
Power Cable Fault Locators
-
We're professional power cable fault locator manufacturers and producers in China, supplying the best customized service. Feel free to buy high quality power cable fault locator from our factory. All our portable products used in utility locations are with CE certification.
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
Product
PXI Fault Insertion Insertion Switch Modules
-
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
Product
Visual Fault Locator
FFL-210-U
-
FFL-210-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in CW (continuous) or MOD (1Hz modulation) mode. There are two LED indicators：RED & GREEN; the RED one shows the operating mode of the Laser Diode output signal, and the GREEN one indicates low battery level. FFL-210-U is housed in a pocket-size, rugged metal casing, comes with a carrying pouch.
-
Product
Tool, Locator, Thermocouple, Receiver
910104134
Locator Tool
Used with Crimp Tool Part # 910101102 to crimp thermocouple receiver contacts.
-
Product
Stimulus Induced Fault Testing
SIFT
-
SIFT allows for the analysis of numerous stimuli to identify speed, fault, and parametric differences in silicon. The heart of the SIFT technique revolves around intentionally disturbing devices with external stimuli and comparing the test criteria to reference parts or timing/voltage sensitivities. Synchronous interfacing is possible to any tester without any wiring or program changes. The system can be based on either a motorized probe station or portable microscope stand for test head applications.
-
Product
Earth Leakage Circuit Breakers
-
Mitsubishi Electric Automation, Inc
Like molded case circuit breakers, these circuit breakers are utilized to open/close low-voltage circuits and protect wiring by automatically closing circuits when they''re overloaded or if a short-circuit occurs. We offer a comprehensive range of circuit breakers that provide superior performance in electrical protection, isolation and power distribution applications. Our circuit breaker products comply with various standards such as JIS, IEC, EN, GB and UL/CSA, and with easy to install accesories, the Mitsubishi Electric circuit breakers are "user-friendly" and ensure the best solution for virtually every application.
-
Product
End-to-End Testing of Location Based Services Software
-
LBS Tester provides an end-to-end test bed for Mobile Network Operators and Network Equipment Manufacturers, to verify the accurate implementation of the location services network. The LBS Tester tests that the Location Server (System Under Test) is correctly executing the positioning procedures over the control plane and/or user plane of that network. To test normal signaling, or failure scenarios, over the LTE User Plane as the number of SETs (SUPL Enabled Terminals) simulated by the LBS Tester increases, the Location Server must execute LPP (Location Positioning Protocol) procedures over SUPL (Secure User Plane Protocol) with success, or without, respectively.
-
Product
Ground Fault Monitor
IFT-120
-
Our ground fault monitors enable you to easily and quickly find the source of the fault before a major problem occurs and damages your equipment. This is the IFT-120, designed to assist you in rapid identification of ground faults.
-
Product
Digital Earth Resistance Tester
8PK-ST1520
-
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
Product
PXI 5A Fault Insertion Switch 5-Channel
40-196-101
Fault Insertion Unit
The 40-196 is a 10 Channel 5A Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Shorting relays on each channel enable UUT signals to be subjected to external user applied fault conditions or to be shorted to the adjacent signal in the same channel. Relays in line with the signal allow open circuit conditions to be simulated on either side or both sides of a channel signal pair. The switching topology of the 40-196 allows channels to be interconnected so that complex fault insertion systems can be constructed.
-
Product
Visual Fault Locator
-
Shanghai Baudcom Communication Device Co.,Ltd.
This Pen-type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical networks. It finds breakpoints, poor connections, bending or cracking in fiber optic cables
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
