-
product
Bench-top Test Jigs
Robust, easily customised, standalone kits for testing a variety of PCB's. Basic hinged-top or cam operated pusher plate, advanced cam-operated gate with fully adjustable pusher-fingers.
-
product
Material Test Machines
Sanwood Environmental Chambers Co ., Ltd.
Sanwood Universal Test Machines, UTM, are widely use for different material testing, like semi-product & finished product made of rubber, plastic, metal, nylon, non-woven fabrics, textile, tape, polyfoam, waterproof materials, wire, cable, etc. With different test jigs or fixtures, the UTM can run the tensile, compression, shearing foce, adhesion, peeling force, tear strength, fatigue, etc test according to GB, CNS, ASTM, ISO, DIN, JIS, EN test standards.
-
product
Displacement Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
Displacement Measurement module comprises of LVDT with micrometer jig fitted on the base plate to give displacement to the core of LVDT. Digital 3½ digit indicator is supplied to read the displacement in mm.
-
product
Grips and Fixtures for Test Stands
AMETEK Sensors, Test & Calibration
Our comprehensive range of grips, fixtures, jigs and probes cover most test applications within a wide range of industries. Below you will find a selection of our most popular grips, fixtures, jigs and probes. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
product
Soft Board Dedicated Automatic Testing Machine
U690FPC
1. CCD automatic alignment, the alignment accuracy reaches ± 15μm2. Support layout test, displacement function3. Up and down jig fine adjustment function4. Soft board stretching function5. Automatic marking function
-
product
Test Extension Boards
XJIO
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
product
Energy Saving System
ECO-Vibe neo
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
product
Full-Automatic Testing Machine for Hard Board Vehicles
U800HDIR
. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Optional laser marking5. Support SHOPFLOOR report output6. Optional BARCODE READER
-
product
Test Fixtures & Jigs
A test fixture or test jig is the component containing the bed of nails used for testing the PCB or assembled product. It is powered and controlled by the Yelo Testpoint system which has test cards capable of providing multiple test conditions. This system also controls the probes used in the bed of nails, and relays test information back to the Testpoint system to be analysed.
-
product
Custom Fixtures
Joule mechanical design and manufacture capabilities allows us to create other custom projects to meet your test needs. Joule can design burn-in racks, jigs and stand-alone test station.
-
product
Customized Material Testing Machines
Globally growing innovations result besides fulfillment of new testing standards in an ever increasing demand for customer-specific solutions regarding the testing technologies, jigs, measuring systems, software and the automation level of the testing machines.The core competencies of TIRA are customer-specific solutions.TIRA is able to realize individual customized solutions according to customer´s request and the simplest derivations like longer, wider, narrower, shorter material testing machines.
-
product
Software Module with a Virtual Gage for Real-Time Inspection and Assembly
Verisurf Build
Verisurf BUILD is the industry-leading tool for real-time model-based inspection, tool fabrication, and computer-aided assembly.Inspect position and profile, set details and fabricate tools, jigs, and fixtures faster and at lower cost than any other process or software.Evolved and perfected from a large installed base at today’s modern aerospace, automotive, and industrial tooling manufacturers.
-
product
Optical Fiber Tensile Jig
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
product
ESI Test Jig
MS 1543
This Test System designed to test the analog, discrete, Ethernet, RS232, RS422, Synchro /Resolver and SPI Signals. It is standalone test equipment and has GUI ATP Software interface with laptop/PC through RS232/Ethernet Interface.
-
product
Probe Placement JIG
456 & 355
The Elcometer Probe Placement Jig is the ideal accessory for measuring coatings on small or complex components when the highest levels of repeatability and accuracy are required.
-
product
Fixture and Software for Open/Leak Inspection
In addition to jigs and fixtures for probing conductors and electrode pads, NIDEC-READ provides specialized software for test point selection and log analysis.
-
product
Engine Simulator
MS 1118
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
product
Hamburg Wheel-Tracking Tester
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
product
Hardware Platform
SmartScan 3D
SmartScan-3D is another hardware platform that allows 3D scan using a six axis robot and DUT holder. A DUT is placed on a 360 degree rotating DUT holding jig. Vertical scanning without rotating DUT holder is one variation of SmartScan-3D for any DUT that is standing up, rather than laying flat on X-Y plane. Any scan technology can be integrated to the SmartScan-3D.
-
product
Fiber Optic Crank Angle Measurement System
CP-5730/CP-0610/CA-6000B
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5730 Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-0610 Rotation stop jig.
-
product
Fully Automatic Test Machine for Ceramic Substrates
U800CCT
1. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Automatic loading and unloading of magazine5. Automatic bad marking and verification of scratches
-
product
MCB Thermal Verification Test Bench
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
product
SRJ (for IBP sensors)
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
product
Compression Test Jig For Foam Rubber Specimens
JIS-based compression testing of foam rubber used in seats can be performed. This machine comprises exclusive accessories added onto an Autograph precision universal testing machine.
-
product
Mechanical Bench-top Test Jigs
CGF Series
Advanced test jig, using a cam-operated, fully adjustable gate - self customisation.
-
product
Ceramics Bending Test Jig
These test jigs enable 3- and 4-point bending tests in accordance with various JIS, ISO and ASTM standards.
-
product
Precision Metal Clad Shunt Resistor
IRHF
Precision Metal Clad Resistors designed in four- terminal technique, are distinguished by high load capacity as well as excellent accuracy. Isolated voltage and current connections making them suitable for very precise current measurements. Easy current measurement is performed by attaching to current bus directly and connecting to voltage (ampere) metal through flexible wires. The ULH models are UL approved versions. Units have a low inductance, heavy copper terminals. The main application is battery manufacturing test jig.
-
product
Package Probe
Test Socket
Jigs for testing the electrical characteristics of devices in the final testing stage after LSI package assembly.To match the increasingly high functionality of LSIs for communications and networks, such as mobile phones and mobile devices, we provide two types of test sockets: The "J-Contacts" series suited for high-frequency, high-performance devices, and the "BeeContacts" series, spring probes with a unique structure that delivers excellent contact stability.
-
product
Digital In-Circuit tester
MTS180/300
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
product
RF Products
We also provide measurement jigs for tests and measurement, and custom-designed products responding to your specific measurement and testing needs.
