Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
6 Relay/18DI/6DO IoT Modbus/OPC UA Ethernet Remote I/O
ADAM-6366
-
OPC UA empowers Modbus I/O users to access the industrial IoT world.OPC UA I/O links SCADA and the cloud without the need for gateways, accelerating OT and IT convergence.Hardware and software double security levels to prevent being hacked.Cost-effective: high I/O density and daisy-chaining solution save cost.
-
Product
High-Density 128-CH Isolated DIO/DI/DO PCI Cards
PCI-7442/7443/7444
-
Responding to the industry"s need for high-density digital input/output modules, the ADLINK PCI-7442/7443/7444 DIO card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications. The PCI-7442/7443/7444 series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442) or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection, these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital inputs.
-
Product
PXI Multifunction I/O Module
-
The PXI Multifunction I/O Module provides I/O with varying numbers of channels, sample rates, and output rates with precise timing, triggering, and synchronization between models. This module can be used for industry applications such as laboratory research, design verification test, and manufacturing test.The PXI Multifunction I/O Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
-
Product
Dynamic Digital I/O (3U), 32 Channel, 100 MHz
GX5291-100
-
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.Dynamic Digital I/O (3U), 32 ch. up to 100 MHz w/128MB On-Board Memory, 32-ch Domain.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (64-out LVDS, 8 SE, KU060)
787281-01
-
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
4-Ch, 16-Bit Isolated Analog Output EtherCAT Remote I/O Module
AMAX-4820
-
Suitable for EtherCAT networks4-ch, 16-bit analog output channels with 2,500 VDC isolationVoltage or current output with multiple rangesQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
-
Product
Analog Oscilloscope
FS-404
-
*OSCILLOSCOPE: 40 MHz Dual Trace,Dual Trigger, 1mV Sensitivity, 10ns Resolution.*FUNCTION GENERATOR: 0.5Hz~5MHz Frequence, Sine,Square,Triangle,3 waveforms, Max output:20 Vp-p(No Load),10 Vp-p(50Ω? Load)., TTL Synchronous Output
-
Product
Analog Oscilloscope
PS-600
-
*60MHz DUAL TRACE, DUAL TRIGGER.*VERT SENSITIVITY FROM 1mV/DIV TO 15V/DIV.
-
Product
Analog Oscilloscope
PS-505
-
*50MHz Vert. Band width*Dual & Trace, ALT Trigger, Z-Input, Y-output*1mV/DIV Sensitivity*10ns/DIV Resolution
-
Product
2-Ch 24V HTL Incremental Encoder/Counter EtherCAT Slice IO Module
AMAX-5080
-
Channels: 2Counting Range: 32-bitMode: Counter (up/down, bidirection, up, A/B Phase)Signal Input: Logic level 0: 0 ~ 3 VDC, Logic level 1: 10 ~ 30 VDCInput Frequency: 5 Hz ~ 1 MHz max. (frequency mode), 1 MHz max. (counter mode)
-
Product
Analog Meter
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
Are electromechanical devices that drive a pointer against a scale.
-
Product
6DI I/O Module With 1RS-485 I/O
WISE-S251-A
-
6 digital input with 1RS-485Modular IoT I/O module to pair with WISE-4200 series
-
Product
PXIe-7847, Kintex-7 160T FPGA, 500 kS/s, DRAM PXI Multifunction Reconfigurable I/O Module
784144-01
-
Kintex-7 160T FPGA, 500 kS/s, DRAM PXI Multifunction Reconfigurable I/O Module—The PXIe‑7847 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7847 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7847 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
PXIe-7867, Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
785570-01
-
Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module—The PXIe-7867 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 18 analog output channels connected directly to the FPGA, you can quickly design for applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7867 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7867 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
-
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
USB-6525, 16-Channel, 60 V, 8 Solid-State Relays, 8 Inputs, Ch-to-Ch Isolated Digital I/O Device
779640-01
-
The USB-6525 is an industrial, bus-powered USB I/O device that can automate even the most demanding applications. The solid-state relay outputs are ideal for controlling pumps, valves, motors, and various other industrial actuators. The USB-6525 features channel-to-channel isolated digital inputs that you can use to read from industrial digital sensors, and eight solid-state relay outputs featuring 60 VDC/30 Vrms switching voltage and 500 mA per channel maximum switching current. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators.
-
Product
GPIB Analog Interfaces
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
I/O Connectivity
-
I/O modules are installed into your real-time target machine and come with Simulink driver blocks and full documentation. The majority also include a set of I/O cables and terminal boards.
-
Product
Smart Analog IC502
-
Smart Analog for High-speed instrumentation amplifier for motor control
-
Product
Digital I/O
-
User programmable 3U PXI FPGA cards for digital and mixed signal applications. Utilizing Altera FPGAs and incorporating a base board / expansion board architecture, our FPGA products offer users the flexibility to create high performance, customized digital and mixed signal instrumentation for specific applications without requiring the use of external interface cards.
-
Product
Digital I/O
-
ADLINK digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports up to 256-CH high-density on a single board, making them suitable for I/O status monitoring and ON/OFF control applications.
-
-
Product
6U OpenVPX Multi-function I/O Board
67C3
-
NAI's 67C3 is a 6U OpenVPX Multi-function I/O and Communication Board with six function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Analog Panel Meters
-
Analog panel meters offer accuracy and dependability and are available in Panel Board, Surface and Window mount styles. We offer variety of AC and DC input panel meters such as ammeters, voltmeters, frequency meters, elapsed time meters, etc.
-
Product
64-Channel Boundary-Scan Digital I/O Scan Module
JT 2111/MPV DIOS IDC
-
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.
-
Product
Serial Analog Interface
Model 2361B
-
* Model 2361B-24 Provides four isolated analog outputs with programmable ranges.* Provides four isolated high-current drive signals and 8 digital inputs. * Includes 4 floating analog inputs.* 1 U high rack mount kit mounts one or two 2361Bs.* Includes US 115 VAC Power Adapter* Compatible with our earlier 2361 and 2361As.
-
Product
4-CH Analog Output Module
ND-6024
-
- Channels: 4- Voltage Output: -10 V to 10 V- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.02% of FSR- 7 TTL digital input
-
Product
8-Ch, 16-Bit Isolated Analog Input EtherCAT Remote I/O Module
AMAX-4817
-
Suitable for EtherCAT networks8-ch, 16-bit analog input channels with 2,500 VDC isolation±275 V high common-mode voltage rangeQuick removable European type connectorSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo rotating switches for up to 256 slave IDs
-
Product
USB-6356, 8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782260-01
-
8 AI (16-Bit, 1.25 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6356 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6356 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
