Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
Analog Output Module
ND-6021
-
- Voltage Output: 0 to 10 V- Current Output: 0 to 20 mA, 4 to 20 mA- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.1% of FSR (current); ± 0.2% of FSR (voltage)
-
-
Product
Analoge Sound Level Meter
Model KM-20/ YF-20
-
Kusam Electrical Industries Limited
One-handed simple, easy to operate. Inbuilt reference signal. Inbuilt battery test. Quickly, accurately sures sound level. Compressed scales minimise range switching. An internal reference signal is available for checking the meter’s operation. Calibration Check. Microphone with Capacitance Microphone.
-
Product
Keysight Multifunction Module with 32-bit DIO, 2-ch D/A and Totalizer for 34980A
34952A
-
The Keysight 34952A module for the 34980A Multifunction Switch/Measure Unit allows great flexibility for a variety of sense and control applications.It combines the following on a single earth-referenced module:
-
Product
PXI Opto-Iso Digital I/O 32bit out 16bit in
40-490-002
-
The 40-490 Digital I/O Modules are designed for applications requiring optically isolated digital I/O, typically in industrial automation. This modules features 32 digital outputs and 16 digital inputs which may be programmed by word or individual bit. Power for the isolated section of the module is built onto the board in model 40-490-001, or this can be supplied externally in model 40-490-002.
-
Product
Analog Input Module
IP340
-
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. A FIFO buffer holds the first bank’s data while the second bank is converted. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
Product
8-CH Analog Input Module
ND-6017
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
PXIe-4322, 16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module
782878-01
-
16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module—The PXIe‑4322 is a channel‑to‑channel isolated analog output module with integrated signal conditioning. The device provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters on the same device, the PXIe‑4322 isolated analog output module delivers a smaller footprint and higher measurement performance. In current mode, the module operates in all four quadrants, so you can both sink and source current. Isolation and higher voltage and current outputs make this module ideal for automotive applications.
-
Product
16-CH Latching Relay Outputs & 16-CH Isolated DI Card
PCI-7256
-
- Supports a 32-bit 3.3 V or 5 V PCI bus- 16-CH latching SPDT relay outputs- Power saving on relay actuation- Output status unchanged when power-off- On-board LED indicators for relay status
-
-
Product
Analog Power Supply
Type NPS-2412
-
National RF's Type NPS-2412 analog power supply was designed to be used in communication equipment where radiated switching inverter noise from conventional “switching type” supplies is not acceptable. The power supply consists of a standard rectified transformer output driving a pair of voltage regulators and filtering networks. The 2412 offers an adjustable voltage output between 2 and 24 volts as well as a fixed voltage output of 12 volts. A maximum of 20 Watts of DC power can be supplied from the unit. As the voltage regulators dissipate power in the regulation process, the power to the load is derated accordingly, dependent on the set voltage to the load. The adjustable regulator is a standard LM-317T integrated circuit device. The fixed regulator is a standard LM 7812 device. Upon customer request, the LM 7812 device may be changed to any voltage rating within the the LM-78xx series of regulators. Contact National RF for this modification if desired.
-
Product
Analog Clamp Tester (CE)
M-3000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High accuracy analog display with strong taut band meter.*Meter lock function.*AC current, AC/DC voltage and resistance measurements.*Conform to IEC safety requirements.
-
Product
IP-Parallel-IO
-
IP Compatible card with 48 programmable TTL IO or 24 - RS422 / RS485 compatible differential pairs. 5 mixed combinations available. Filtered or direct input. Programmable interrupt from each IO [TTL or differential]. 2 counter timers. Waveform generator.
-
Product
Analog IC test system
-
A paradigm shift has been occurred in Japan’s major brand WL25 series tester. Ultimate simple system is available by effective analog pin architecture.This cost performance system is covered analog IC extensively, which are high accuracy, speed and multi-site test function.
-
Product
Multi-Function PXI Card
GX3788
-
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
Product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
-
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
Product
Multifunction I/O Boards
-
NAI offers a variety of rugged embedded boards - both Multifunction IO Cards & Single Board Computers in OpenVPX, cPCI, VME and PCI/PCIe form factors. When combined with our smart function modules they have the ability to meet a wide range of complex and time-critical sense and response requirements for I/O-intensive, mission-critical applications.
-
Product
Analog Isolation Board
MSXB 027
-
The MSXB 027 Analog Isolation Board accommodates up to 8 isolation modules in any combination of input and output. Up to 64 5B Analog Isolation Boards can be connected to a single DAP for a total of 512 isolated channels. When used in conjunction with Analog Output Expansion Boards, up to 66 of these channels can be specified as isolated analog outputs.
-
-
Product
12DI/12DO Intelligent I/O Gateway
ADAM-6750
-
Linux Open Platform12ch digital input(counter)/12ch digital output(pulse output)Programming: linux C API, Node-RED (graphic programming environment)Cloud/Database access ,edge data analysis and logic control, data visualization by dashboardInterfaces: RS-485x2, Ethernet port x 2 ,1 x USB Type-A 2.0, 1 x USB Micro-B 2.0
-
Product
PCIe-Mini -IO Controller
PCie-Mini-CAN-USB
-
The PCIe-Mini -CAN board is engineered around the NXP LPC2387 microcontroller.This highly integrated 32 bits microcontroller based on the ARM7TDMI-S processor, has a very low power consumption and features 512 kB of on-chip high-speed flash memory.
-
Product
General Purpose I/O Modules
HY-TTC 36X
-
HY-TTC 36X is a CANopen-based, cost effective, modular and user-friendly solution for extending the number of I/Os in mobile applications. This controller is best suited for different kinds of control tasks in a vehicle and acts as slave unit in a CAN-based network architecture.
-
Product
Dynamic Digital I/O Instrumentation
-
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
Product
Analog Input Module, 12-bit A/D
IP320A
-
The IP320A monitors 20 differential or 40 single-ended input channels. When used with a carrier that holds four IP modules, up to 160 inputs can be obtained from a single card cage slot.
-
Product
Remote I/O
-
Reduces wiring costs, simplify troubleshooting and minimize downtime with Omron's high density I/O modules and other socket-based I/O products.
-
Product
A PoE-PD I/O Board
AX93274
-
*PoE-PD I/O board complies with IEEE802.3at standard via an internal cable to power on SBC*100 x 32 mm*1 x LAN cable, 1 x power cable, 1 x thermal module*Compliant products: PICO831, PICO121, PICO841, PICO843
-
Product
PC/104 Analog Output Board
104-AO12-4
-
The following functions are available in many configurations giving the user the ability to specify exactly what’s needed. Interrupts are individually or globally enabled or disabled via software. A status register is provided to determine the interrupt source.
-
Product
PXI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module
778543-01
-
48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, PXI Digital I/O Module—The PXI‑6528 is an industrial, parallel digital I/O interface. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Analog Output / Arbitrary Waveform Generator
GX1632e
-
The GX1632e is a 3U PXI Express digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1632e offers 32 output channels with 16-bits of precision signal sourcing performance. Three modes of operation are available including Analog Output, Arbitrary Waveform Generation (ARB) and Data Streaming.
-
Product
High Density I/O Module
ADAM-500 Series
-
Remote I/O modules for multi-channel thermocouple data acquisition with Modbus RTU/TCP support, ideal for precise temperature monitoring.
