Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
Product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
-
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Oscilloscope: 200 MHz, 4 Analog Channels
DSOX3024T
-
The DSOX3024T, 200 MHz oscilloscope provides 4 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate and standard touch zone trigger with an 8.5-in capacitive touch screen.
-
Product
mAEStro Audio Digital to Analog Converter
-
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
Product
Telephone Line Testers for POTS / Analog Line
-
*This analog line tester is suitable for all instalers installing telephone equepement on POTS line.*Led indications signaling the status of analog line.
-
Product
PXI 8 Slot BRIC 276x8 1-Pole Dual Analog Bus (6 sub-cards)
40-560A-121-276X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
4U Front I/O Short Depth Rackmount Chassis
IPC-631
-
4U Front I/O Short Depth Rackmount Chassis for ATX/MicroATX Motherboard
-
Product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Analog RF Slot Downconverter: 2000-2400 MHz Input
Model 8111-005
-
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
Product
Ethernet I/O Modules
ADAM-6000
-
Advantech's Ethernet I/O Modules, ADAM-6000 series, accomplishes this integration easily through the latest internet technology, so that it can remotely monitor the device status more flexibly. ADAM-6000 modules are empowered by Peer-to-Peer (P2P) and Graphic Condition Logic (GCL), and can perform as standalone products for measurement, control and automation with Advantech's P2P and GCL technology.
-
Product
1-Port Isolated RS-232/422/485 Communication EtherCAT Slice IO Module
AMAX-5090
-
Versatile Communication: The AMAX-5090 supports RS-232, RS-422, and RS-485 communication, making it adaptable to various industrial applicationsSeamless Data Transfer: With TxD and RxD channels and full/half-duplex capabilities, it ensures smooth and reliable data transmissionEffortless Integration: Interfaces for UART and Modbus RTU to EtherCAT simplify integration into existing systemsRobust Performance: Featuring a 1,000-byte receive and transmit buffer and a wide range of baud rates (1,200 to 115,200 bps), it guarantees efficient and high-speed data processingRugged and Reliable: Built for demanding environments, it operates in temperatures ranging from -25°C to 60°C and is compliant with RoHS standards
-
Product
SCB-100 Noise Rejecting, Shielded I/O Connector Block
776990-01
-
100-Pin Female SCSI to 100-Pin Female Screw Terminal, Desktop Mount Terminal Block - The SCB-100 is a shielded I/O connector block for interfacing I/O signals to NI data acquisition devices with 100-pin connectors. Combined with the shielded cables, the SCB-100 provides rugged low-noise signal termination.
-
Product
Light-to-Analog Sensors (Current)
-
Renesas' light-to-current silicon optical sensors combine a photodiode array and current amplifiers on a single monolithic IC. These devices are ideal for display and keypad dimming, as well as industrial and medical light sensing applications.
-
Product
Isolated Analog Input Expansion Board
MSXB 084
-
The MSXB 084 Isolated Analog Input Expansion Board provides isolated analog inputs for DAP systems. Use these boards to eliminate ground currents – a potential source of noise in your measurement and control signals – and eliminate timing skew.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
-
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
Analog Temperature Sensors
-
Analog Devices analog temperature sensors provide current or voltage output proportional to the absolute temperature with accuracies of up to ±1°C. Our diverse range of analog output temperatures sensors can be used in a broad range of applications with no need for external calibration, and with minimal signal conditioning/conversion circuitry. To better suit your varied design needs, our portfolio of temperature sensors are available in multiple package options.
-
Product
I-87K Data Acquisition Modules Via RS-485 / DCON Protocol - Cartridge Based I/O
-
ICP DAS I-87K serial cartridge based I/O modules offer the ultimate in cost effective flexibility, when it comes to a localized COTS data acquisition program. The ICP DAS I-87K COTS cartridge based I/O program offers a multitude of digital and analog configurations, which are communicable via an proprietary backplane in all of ICP DAS's W-8000 & 87K series rack mount controllers and expansion racks!
-
Product
Advanced Programmable IO Board
MS 1508
-
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
Product
Analog Multiplexer Board
104-AIM-32 PC/104
-
The 104-AIM-32 is an analog signal multiplexer conforming to the PC/104 standard. The card will multiplex and condition 16 differential or 32 single-ended analog signals before passing them to an analog-to-digital converter card like the 104-AIO12-8. A system may comprise one to seven of these cards in tandem with one 104-AIO12-8 A/D converter board. The 104-AIM-32 card may be used as part of a large data acquisition system. The 104-AIM-32A Kit consists of one 104-AIM-32 and one 12-bit 8-input A/D board.
-
Product
RF Shielded Test Enclosure, I/O Intensive Device Tests
JRE 1720
-
Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan. A JRE exclusive, our triple door locking mechanism allows easy single handle door operation. Ventilation is standard with our JRE exclusive honeycomb style vents in enclosure rear and door.
-
Product
Analog Output DAQ Cards
-
Analog output cards are ideal for DAQ applications where multiple A/O channels are needed for voltage and current output.
-
Product
4Relay/4DI IoT Modbus/SNMP/MQTT 2-Ports Ethernet Remote I/O
ADAM-6266
-
4ch relay/4ch digital input(counter)Protocols:MQTT(TLS),SNMP,Modbus TCP,RESTful,ASCIIGCL to perform basic logic control rulesCloud access: Data update to AzureAuto-bypass function to ensure daisy-chain data transmissionPeer-to-Peer function to map I/O statusBuilt-in web serverWatchdog timer to recover the system
-
Product
Analog Noise Generator
PNG7000
-
The PNG7000A Series instruments generate white Gaussian noise and provide a summing input to control signal-to-noise (SNR) or carrier-to-noise (CNR) for bit-error-ratio (BER) testing. The output can also be used as a source for Jitter applications.
-
Product
SPS link-up via 24 volt I/Os
HSM-24V
-
The module HSM-24V provides 32 digital inputs/outputs for 24 V level and links ADwin up to e. g. the world of SPS-like signals.
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
-
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
Oscilloscope 70/100/200 MHz, 2 Analog Channels
DSOX1202A
-
The DSOX1202A oscilloscope provides 70, 100, or 200 MHz of bandwidth on 2 Analog channels
-
Product
EtherCAT I/O Modules
-
AMAX EtherCAT I/O delivers different form factor to meet diversified application scenarios - Slice I/O and Block I/O
-
Product
Modular Analog & Digital Systems Solid-state, Digital and Relay Modules
G2T Series
-
Universal Switching Corporation
Our Series G2 product family is a field proven and versatile modular platform for both signal switching and distribution. Numerous digital and analog configurations and modules are available for a cost effective and compact solution.
-
Product
Remote Ethernet Modbus TCP I/O Modules
-
ET-7000 Modbus TCP Remote Ethernet I/O allow configuration, I/O monitoring and control through a regular web browser. Besides Web HMI function, no more programming or HTML skills are required; creating dynamic and attractive web pages for I/O monitoring. They can be easily integrated with SCADA software and other I/O. They come with EZ Data Logger Software for data logging and monitoring systems.
-
Product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Regular Flex I/O For Reset, Remote Switch And 5VDC
98R17500802
-
Flex I/O expansion on the front panel for same-side cablingReset, Remote Switch and 5VDCSupport MIC-770 V3 Fanless system
