Shielding
Protects against or confines electromagnetic or ionizing radiation.
See Also: Shielding Effectiveness
-
Product
Starter Kit For B2985/B2987
N1410A
-
The N1410A is a starter kit for B2985B and B2987B Electrometer/High Resistance Meter and includes N1414A High resistance measurement universal adapter and N1415A Triax to alligator cable. The N1414A helps you setup the cables and makes the cabling setup easier. The N1415A is recommended to measure more than 1 nA current, but you can probably measure less than 1 nA current with appropriately shielding.
-
Product
Multi-Network Cable Tester
3PK-NT007N
-
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
Product
Antenna Couplers
-
Concentric Technology Solutions, Inc.
RF Antenna Couplers help create the ideal environment for shield boxes by providing a consist, stable and reliable environment for repetitive over the air (OTA) tests.
-
Product
Instrument EX UnShield Cases
-
The Optima Stantron EX (unshielded) and ER (shielded) family of instrumentation cases are designed to house EIA standard 19” wide sub-racks and chassis. The rugged yet lightweight and stackable structural design is achieved with rigid front and rear aluminum bezels joined by rounded, extruded aluminum corner members. All panels - side, top and bottom are constructed of 18 ga.
-
Product
Shield
Arduino MKR Therm Shield
-
The MKR THERM Shield allows a board of the MKR family to acquire temperatures from a thermocouple of type K and a DS18Bxx digital one wire sensor. The Thermocouple is a kind of temperature sensor that offers high accuracy and a wide range of measured temperatures. Its analog nature requires specific interfacing and this shield relies on the MAX31855 thermocouple digital interface.
-
Product
Micro Coax, Contact, ITA, RG316 Double Shield
610141104
-
Primary mating contact 610140104. (May mate with other Receiver contacts, as well.)
-
Product
DB37M-DB37F-EP, 37-Pin Shielded Cable - 4 AI, 4 AO, 10 DIO
193737-01
-
DB37M-DB37F-EP, 37-Pin Shielded Cable - 4 AI, 4 AO, 10 DIO
-
Product
RF Shielded Box
LTL B12001
-
LTL B12001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B12001 RF shielded test enclosure can comfortably houses the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
20dB In-Line Amplifier
HSA-20
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Excellent Zinc die-casting chassis, with good shielding feature. *All ports can be passed by DC. *Output ports are F-British system, impedance 75Ω.* Perfect technique of superficial treatment guarantees frequency respondence.
-
Product
DataComm & LAN Testers
-
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
Product
Integrated Potentiostat and Multiplexer
EmStatMUX8
-
Based upon the EmStat range, there are two types of multiplexers to suit most types of sensor array work. The MUX8 is the most flexible offering the ability to connect arrays made of up to eight working electrodes in two or three electrode cell types and chips sharing a reference electrode and/or counter electrode. The MUX16 is suitable for sensor arrays or chips with sixteen working electrodes all sharing a RE and/or a CE. Both instruments are suitable for laminated layer corrosion analysis.The potentiostat is controlled and powered by USB and is used with PSTrace allowing for simultaneous sampling of each channel at a rate of 25 ms/channel. Standard packaging includes a shielded cable with connections for a working, a counter and a reference electrode by means of 2 mm banana connectors and mini-crocodile clips, a stripped end, Dsub-37 terminated flat cable and a USB cable. To make connections to chips simpler the Connection Terminal is an optional extra providing clearly marked screw terminals to the electrodes and can be directly joined to the ESMUX via their D-Sub connectors.
-
Product
*Micro-fluoroscopic X-ray Inspection System
Cath-X
-
The Cath-X is a bench top system employing Glenbrook’s micro-fluoroscopy technology providing highly detailed x-ray video of the critical components of the needle device. The transparent, safely shielded, view chamber permits the operator to locate the critical areas of the needle for inspection. The x-ray image can be further magnified using the electro-optical zoom feature of the Cath-X.
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
