Platinum Resistance Temperature Detectors
offer precision; accurate, repeatable, stable and linear thermometry.
See Also: Platinum
-
Product
Phase Failure Detectors
DSP
-
Your product The DSP-1L or DSP-1LM is used to protect your three-phase motors against phase loss, imbalance, or reversal. It continuously monitors each phase of your power supply. In case of a problem, it cuts the power to the control circuit to protect the affected motor.
-
Product
Programmable Insulation Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Electrical resistance testingLCD displayOutput Voltage: 1.0V~1000VThe insulation resistance range:100kohm to 100Gohm
-
Product
Detectors
-
Each detector is properly housed, complete with any associated circuitry and can be mounted directly at the exit slit of any of our monochromators.
-
Product
Tin Side Detectors
-
Tin Side Detector Lamp (Model # TS1301)Our NEW Tin Side Detector (Model# TS1301) allows you to determine the tin side of float glass. The instrument can test clear float glass or glass that has other specialty coatings applied to it in mos..
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Multi-channel Resistance Meter
-
Changzhou Applent Instruments Inc.
Can scan and test 10 channels of resistance and can set a comparator for each channel. Its temperature compensation function can adapt different testing requirements. It can be applied to automation equipment.
-
Product
Voltage Detectors & Testers
-
Non-contact AC voltage detector quickly checks for the presence of live voltage on wiring and electrical devices. Features a built-in flashlight for added convenience.
-
Product
Portable Temperature Monitor
PTM1
-
The Model PTM1 is a high performance, precision hand-held instrument for the measurement of temperature using Physitemp’s Type T (copper-constantan) thermocouples (will also accept J & K). This versatile instrument measures temperature in both °C and °F. The internal memory of the microcomputer stores the minimum and maximum measured temperature range for instant recall via the LCD display.
-
Product
Phase Detectors
-
Macom Technology Solutions Holdings Inc.
MACOM's MSPD Series Integrates an SRD reference frequency multiplier, coupling capacitors and a Schottky diode microwave sampler / phase detector in a 0.075” by 0.100” hybrid. They are used to phase lock microwave oscillators up to 22 GHz to a much lower reference frequency by deriving a locking voltage from the sampled RF and the multiplied reference.
-
Product
Insulation Resistance Tester For PV
MSEI-200C
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This model can measure insulation resistance of DC current circuit in PV systems (between PV module and power conditioner) on the live line and can distinguish the deteriorated part between Power Phase, Neutral Phase, P/N Phase and or PV modules.
-
Product
Ground Resistance Clamp Meter
61-920
-
*Auto ranging*Auto power off*Hard case included*2-year warranty
-
Product
Volumetric Flow Detectors
FP-5000 Series
-
In engine evaluations such as emission mode tests and transient tests for performance evaluation, the evaluation methods have been shifting from steady-state tests to transient tests. In the evaluation of fuel consumption, the requirement for evaluating the fuel consumption characteristics in transient duration has been increasing as well as the total fuel consumption for each mode. The FP-5000 series has achieved high pulse resolution and wide measurement range. It enables to detect changes in the flow rate effectively and responsively, and measure large flow rate. It can be used when the flow rate increases, such as when measuring alcohol fuel.
-
Product
Measuring Earth Resistance
OSP-510
-
Additional equipment to measure the earth resistance and soil resistivity AD-510.
-
Product
Temperature Calibrators
-
Fluke Temperature Calibrators simulate process sensors for testing temperature instrumentation. Specifically designed for the field, these lightweight compact tools are EMI tolerant, dust and splash resistant and offer an easy to use single push button interface. When paired with a temperature sensor they can take high accuracy temperature measurements to verify process temperatures and ensure the highest product quality and safety. There are a variety of different temperature calibrators designed for your unique calibration and testing requirements.
-
Product
Pinhole Detector
NOVOTEST ED-3D
-
NOVOTEST ED-3D Pinhole Detector was designed for rapid non-destructive testing of the continuity of coating (e.g. porosity of film) with thickness up to 500mkm according to ASTM G62-A.Pinhole Detector is designed for testing the porosity of partially painted places and other discontinuities of protective dielectric coatings on metal products by putting low voltage through a sponge which is soaked in a liquid electrolyte with high penetrating properties.
-
Product
Temperature and Pressure
-
Encore Electronics manufactures a complete line of rugged and economical instrumentation for temperature and pressure measurement. Our standard, in-stock units can be used for pressure measurement depending on the signal level and output required. Our equipment is available in both DIN rail and modular/rack-mounted configurations for multiple channel capability. Simply specify your output — whether 4 to 20mA , 0 to 10V, or a custom output and Encore can configure a system to match your needs. Whether you need isolated input and outputs using transducer power or computer-controlled units, we will design and build a unit to meet your requirement.
-
Product
Insulation Resistance Measurement
MD 15KVR
-
The digital insulation tester model MD-15KVR is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation. Its proven technology provides safe, reliable and accurate measurements of insulation resistances up to 15 TΩ, with 4 pre-selected test voltages, 500 V - 5 kV - 10 kV - 15 kV. Other test voltages may be selected in steps of 25 V, 100 V or 500 V.
-
Product
Temperature and Humidity Regulator
H3331-2
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
Globe Temperature Probe
TP3276.2
-
Globe temperature probe with Pt100 sensor, globe Ø 50 mm. Stem Ø 8 mm, length 170 mm. Complete with SICRAM module.
-
Product
Programmable Ground Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Executive test in 40A/60A of UL60950-1Test resistance range 0~510m ohmOutput current range 5~40A
-
Product
Resistance Measurement Meters
-
Shanghai Beha Electronics Co., Ltd.
The meter digital milli-ohmmeter is a battery operated instrument wich supply a low current to the circuit under test, with which, stable, accurate measurement of low resistance can be made, still, over a wide range of values.
-
Product
Resistivity and Hall Effect
-
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements.
-
Product
Partial Discharge Detector
PXDP-II
-
The PXDP-II partial discharge meter is a portable device that performs detection and measurement of partial discharges in electrical devices or components. It records partial discharge measurements for analysis and diagnosis through the optional PC software. The PXDP-II can be used in various applications and complies with IEC 60270.
-
Product
Temperature and Humidity Regulator
H3430
-
Built-in relative humidity, temperature sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
L-Type Multi-Purpose Platinum Sheet Electrode Clip
EH-1
-
EH-1 L-Type Multi-Purpose Platinum Sheet Electrode Clip is an electrode holder, clip or electrochemical cell accessory designed to position electrodes securely and provide stable electrical connection during laboratory electrochemical testing.
-
Product
Radiation Detectors
-
A radiation detector is a device for measuring nuclear, electromagnetic or light radiation. A nuclear radiation detector identifies nuclear radiation by measuring the emission of ionizing radiation of alpha particles, beta particles and gamma rays. Also referred to as a geiger counter, a nuclear radiation detector consists of two main elements: the processing electronics and the geiger tube. The geiger tube is filled with low-pressure inert gas like helium, argon or neon. If radioactive radiation occurs, the inert gas is ionized. An anode within the geiger tube registers the quantity of ionized particles numerically correlating with the strength of the radioactive radiation. The radioactivity measurement is then displayed on the LCD screen of the geiger counter or nuclear radiation detector.
-
Product
Temperature Transmitter and Regulator
H0430
-
Built-in temperature sensor.Temperature transmitter is equipped with three two-state inputs for detection of two-state signals - e.g. power presence, water, smoke, airflow, glass break detection, door contact.
-
Product
Resistance Wire Bonding
-
Electronic Systems of Wisconsin, Inc.
ESW's Resistance Wire Bonding System comes equipped with the latest features the market has to offer. Our system is capable of bonding armatures, stators or coils. The on-screen display in our bonder makes it easy to read, track, and record your bonding data. If desired, ESW offers complete electrical testing of the part prior to the bonding sequence as well. This ensures only good parts that have been electrically tested are processed through bonding. It is our duty to make sure you never have to worry about losing important information again. Our Sales and Engineering staff will work closely with you to make sure that a bonding systems will meet your needs. See the slideshow below to see some of our Resistance Wire Bonding Testers.
-
Product
Non-Contact H.V. Detector
278 HP
-
Standard Electric Works Co., Ltd
Protection class : IP65. 3 LED indicators in a circle for easier viewing in any directions (360° LED indication). 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV. Bright LED visual indication. Frequency range: 40~70Hz. Longer hood makes LED indicators more visible. Audible indication. Easy-to-prove method. Self-test function. Power source : 1.5V "C" type battery × 3. High impact nylon casing. Non-contact detection by proximity. Compatible with most hot sticks. Lightweight, robust & compact. Suitable for indoor and outdoor use. Easy access to batteries. Special ranges are available upon request. The maximum detection range can be 500kV.
-
Product
Voltage Detectors & Others
-
Voltage Detectors, Circuit Breaker finder, Portable working lamp are Indispensable equipment which must always accompany the technician. Its essential characteristics are an extreme handiness, a very high protection degree and easiness of use.
