Microphones
convert sound pressure to an electrical current.
See Also: Phone, Telephone, Geophones, Headphone, Hydrophones, Measurement Microphones, Mic, Electroacoustic, Headset
-
Product
Sound Meters
-
Is used for acoustic (sound that travels through air) measurements. It is commonly a hand-held instrument with a microphone.
-
Product
Acoustic Testing
-
Our acoustic testing experience includes acoustic qualification and evaluating sound pressure levels. We utilize microphones, pressure trans-ducers, and an acoustic intensity meter to record acoustic measurements.
-
Product
Precigrader: Acoustic MSR System
-
Precigrader is an acoustic on-line strength grading system. The system is installed in more than 150 mills. It is used to determine common commercial grades in North America, including 1650 and 2100. A spring-loaded impact mechanism strikes the lumber as it passes. The resulting vibration is captured by microphones to determine the appropriate MSR grade.
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
Microphone Arrays
-
One of the most important parts of an Acoustic Camera is the microphone array. It determines the spatial distribution of the acoustic microphones and therefore measurement performance of the whole system. In order to achieve the maximum possible performance in any given application, we offer a wide variety of microphone arrays. No matter if the measurement is beamforming, intensity or holography ... we have the right microphone array. For special applications we can design and build custom made microphone arrays according to the requirements of the application.
-
Product
MIPI Soundwire Total IP Solutions
Soundwire
-
Soundwire is suited for small, cost-sensitive audio peripherals such as modern digital class-D amplifiers and digital microphones. The Total MIPI SoundWire IP Solution from Arasan enables early adopters the fastest path to adoption of this new standard by offering a comprehensive IP package that includes the Verilog RTL source code for Master and Slave, fully validated for compliance with the standard, a comprehensive test environment with a compliance suite for verification of the IP package, a SoundWire Hardware Development Kit (“HDK”) for FPGA prototyping, a SoundWire protocol analyzer and a complete SoundWire software stack.
-
Product
4ch Beam Forming Sound Source Visualization System
BF-3200/MI-5420A/BF-0310
-
Beam Forming is one of the sound visualization techniques that obtains the sound pressure distribution using the phase differece information from the sound source to the microphone, and makes it visualized with the color map.This technique requires a lot of microphones to cover a wide area and generally tends to increase the size of the system. By this Beam Forming system, Ono sokki achieved real time sound source visualization with just 4 microphones.
-
Product
Dynamic High Pressure Sensors
-
Columbia Research Laboratories
Columbia's line of Dynamic Pressure Sensors can also serve as Acoustic Sensors (Microphones). They are designed to measure fast pressure variations, surges and dynamic blasts. The Sensors vary from low cost, small size, and lightweight to High Pressure (to 10,000psi) units, with all-welded contructions for extreme ruggedness, making them excellent choices for a wide range of applications.
-
Product
Tube MP
-
Applied Research and Technolgy
The world's most popular external microphone preamp - since 1995.
-
Product
Acoustic Calibrator
CAL250
-
The Larson Davis Model CAL250 is a battery operated precision microphone calibrator used for the calibration of sound level meters and other sound measurement equipment.
-
Product
Measurement Condenser Microphone
ECM8000
-
The ECM8000 is a specialized condenser microphone designed for use with real-time analyzers, such as our ULTRACURVE DEQ2496, to provide an accurate acoustic picture of the room. You can then use your graphic EQ to fine-tune your system's performance to perfectly match the characteristics of any acoustic environment.
-
Product
Microphone Preamplifier
426A05
-
Preamplifier for 1/4" side vented prepolarized microphones.
-
Product
Sound Level Meters
-
Dalian Taijia Technology Co.,Ltd
Is used for acoustic measurements. It is commonly a hand-held instrument with a microphone.
-
Product
Class 1 Integrating Sound Level Meter System
NK021
-
This NK021 system includes a class 1 integrating sound level meter, class 1 acoustic calibrator, protective microphone windshield and is supplied in a hard wearing kit case.
-
Product
Electroacoustic Test
-
CRYSOUND offers comprehensive and expert electroacoustic measurement solutions for a broad spectrum of consumer electronics, including headphones, microphones, and speakers. These solutions are characterized by powerful functionality and robust stability.
-
Product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
-
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
Product
Miniature Time Code Recorder
MTCR
-
When the distance is extreme or using a wireless microphone is not practical, the MTCR recorder can travel with your subject and capture professional quality audio, synchronized with timecode. It’s tiny size is unobtrusive and easily placed in garments and costumes, and easy to conceal when used as a “plant” microphone to capture environmental or location sound.
-
Product
Class 1 Sound Pressure Level Meter
Castle Sonus GA116B
-
The entry level of the Castle Pocket Range of Sound Level Meters is the SONUS B(GA116B ), a feature packed, pocket instrument that is fully compliant with IEC 61672-1:2013. This meter gives simultaneous sound pressure (Lp) and peak (Cpeak) measurement for a multitude of tasks including initial spot-check assessments to the Control of Noise at Work Regulations 2005. It has a high-specification measurement microphone and is cased in tough, crack resistant ABS plastic.
-
Product
30KHZ Measurement Microphone
M30
-
Used on countless full-scale concert tours, as well as in scientific research laboratories, tropical rainforests, and rocket testing facilities, the M30 has proven to be a lab-grade audio instrument that can handle any environment.
-
Product
Calibration Systems
-
Brüel & Kjær Sound & Vibration A/S
Our calibration solutions meet the broad variety of needs for calibration in the field of sound and vibration accurate primary and secondary calibration of measuring equipment and the scope of transducers: accelerometers, microphones and hydrophones.
-
Product
Phantom Powered Measurement Microphone System
7052PH
-
The 7052PH Type 1.5TM phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Type 1.5TM - a superior Type 2. Frequency Response: <3 Hz to > 20kHz typ.(capsule). Sensitivity: 22 mV/Pa (-33 dBV/Pa)typ. Dynamic Range (capsule) 1% THD: <20dBA-150dBSPL (Capsule).
-
Product
Test Sockets
MEMS Device
-
Patented MEMS Sockets from Ardent Concepts use a unique scrubbing action contact set which is ideal for today’s sensitive MEMS devices, including accelerometers, gyroscopes, MEMS microphones and other specialized devices used in mobile electronics applications
-
Product
Digital Sound Meter
SM-100
-
Model SM-100 Digital Sound Meter is ideal for measuring noise levels from 30 to 130 dB with accuracy of ±1.5 dB. Model SM-100 has a frequency of 31.5 Hz to 8 kHz, three different dB ranges, and a 1/2" condenser microphone. The SM-100 has two frequency weightings: the "A" weighting ranges from 30 to 130 dB, while the °C" weighting ranges from 35 to 130 dB.
-
Product
Well Camera
Well-Camera.1
-
Taking advantage of our vast experience in designing and manufacturing TV-inspection systems for boreholes and wells, we created the innovative WELL-CAMERA Series that follows all our Customer’ requests about an easy use, reliable, compact and lightweight instrument for field operations. The complete system consist of: reel and camera head, display unit with integrated LCD, USB2 grabber board and microphone, battery charger. Pictures, movies and comments can be saved to any external laptop.
-
Product
A²B® Automotive Audio Bus Solution
ITD 1024
-
ITD 1024 is an off-the-shelf solution for A²B®, an emerging automotive audio bus. In combination with a comprehensive set of software tools, ITD 1024 allows rapid testing of various A²B® components such as audio speakers, amplifiers, microphone arrays, sensors, and actuators.
-
Product
Camera Barrel Test System
BK8612
-
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
-
Product
Sound Level Meters
-
A sound level meter is used for acoustic measurements. It is commonly a hand-held instrument with a microphone.
-
Product
Universal Locator
UL 30
-
Cable fault location with the BAUR UL 30. The UL 30 receiver is used together with a ground microphone (BM 30) and a surge voltage generator (SSG, STG) to pinpoint cable faults. With the coil integrated in the BM 30 for runtime measurement, the device determines the time difference between the magnetic and acoustic signal. This particularly offers special advantages when d ealing with faults difficult to locate acoustically.* Built-in speaker* Splashproof design* Large, illuminated display* Lightweight
-
Product
High-performance LPDA
ALP690
-
The ALP690 is a high-performance LPDA (log periodic dipole array) antenna with a bypassable, built-in RF amplifier for use with wireless microphone receivers in location or studio production. The design delivers +4 dBd of passive gain in a directional pattern to extend operating range, and, when DC power is applied, the amplifier applies gain to overcome loss in long coaxial cable runs. By offering both active and passive operation modes, the ALP690 can be used as a receiver antenna (active or passive) and as a transmitter antenna (passive only).
-
Product
Digital Matrix Processor
DM812
-
The DM812F is a powerful digital audio processing, mixing and routing system. The primary applications are sound reinforcement and conferencing in boardrooms, courtrooms, worship centers, distance learning systems, hotels and other applications with multiple microphones and loudspeakers. The design represents a milestone in DSP technology in its basic architecture and in its processing speed and efficiency.
