Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
Product
Interface Board, 8:1 USB
40-965-903
Interface
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
-
Product
NI-9853, CAN Interface Module
780178-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
LIN Interface Module
C Series LIN
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PXIe-8431, 8-Port, RS485/RS422 PXI Serial Interface Module
781473-01
Serial Interface
The PXIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
Digital/Pattern/PE Card
PA64S
Interface Card
The PA64S represents a new level of performance and capabilities for PXI-based digital instrumentation. The PA64S offers high performance pin electronics and 16 sites of TMU/SPI/I2C/CLK generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be integrated, supporting up to 256 sites (16 boards).
-
Product
Intelligent Double Sized H009 Interface Module for Excalibur 8000 Family of Carrier Boards
M8KH009
Interface Module
The M8KH009 is an intelligent, double-sized, H009 interface module for the multimode, multiprotocol, EXC-8000 family of carrier boards. The M8KH009 provides a complete solution for developing and testing H009 interfaces and performing system simulation of the H009 bus, according to the standard H009 protocol. Each module of the M8KH009 contains 32K x 16 dualport RAM for Data Blocks, control registers, and Look-up tables. In addition, the module contains another 32K x 16 dual-port RAM for a Concurrent Monitor. All data blocks and control registers are memory mapped, and may be accessed in real-time. Each of the independent, dual-redundant M8KH009 modules may be programmed to operate in one of three modes of operation: Central Control Complex (CCC) mode with Concurrent Peripheral Unit operation (1–16 PUs), Peripheral Unit mode (Multiple – up to 16 PUs) and Bus Monitor mode. In addition, the module can simultaneously operate as an independent Internal Concurrent Monitor in CCC, Multiple PU or CCC/Concurrent PU modes.
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
510140125-1
Pull-Thru Adapter
PXI Pull-Thru Adapter, PCB, QuadraPaddle, 68-Pin Male VHDCI
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
3U CompactPCI Serial 4-Port USB 3.2/2-Port Ethernet Card
cPCI-A3USB
Ethernet Interface
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 4x USB3.2 Gen 1 ports and 2x RJ45 2.5G LAN ports in front panel- 1x USB2.0 port on board- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
Interface
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
Product
Attenuator Interconnect Kit, Type-N
11716A
Interconnect Adapter
Quickly and conveniently connect 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716A interconnect kit contains a rigid RF cable, mounting bracket, and necessary hardware to connect any pair of Keysight 8494/5/6/7 attenuators in series. Attenuators must be ordered separately.
-
Product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
Adapter Plate, ITA, f/ G20x or G40x
410112996
Adapter Plate
The G20x adapter plate allows the G20x or G40x ITA to accept 2 modules (iCon) in the lower tier.
-
Product
ARINC 3U/6U CompactPCI Interface Card
CPCIC3/6-A429
Interface Card
Alta Data Technologies’ CPCIC-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB).Encode or decode almost any ARINC-429 physical layer signal.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787455-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
Interface
EPMC-1553-8
Interface
Abaco Systems EPMC-1553-8 is the first PMC (PCI Mezzanine Card) module to offer 8 dual redundant MIL-STD-1553B Notice II channels. Available in commercial, ruggedized and conductively cooled versions with eight dual-redundant channels, the EPMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
Product
PCB Adapter, ITA, QuadraPaddle, 192 Position, To PCB-Mounted 2x68 Pin Female VHDCI Connectors
510151123
PCB Adapter
PCB Adapter, ITA, QuadraPaddle, 192 Position, to PCB-Mounted 2x68 Pin Female VHDCI Connectors
-
Product
RF Adapter Module For FlexRIO
RF Adapter Module
RF Adapter Modules for FlexRIO feature frequency coverage from 200 MHz to 4.4 GHz, with up to 200 MHz instantaneous bandwidth. When paired with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, you can program the FPGA using LabVIEW to implement custom signal processing, including modulation and demodulation, channel emulation, spectral analysis, and even closed-loop control. These modules are all based on a direct conversion architecture and feature an onboard local-oscillator which can be shared with adjacent modules for synchronization. RF adapter modules also provide digital I/O capability for interfacing with external hardware.
-
Product
PXIe-6594, FlexRIO High-speed Serial Module (28 Gbps), KU15P
786939-01
Serial Interface
PXIe, 28 Gbps, 8-Channel PXI High-Speed Serial Instrument. - The PXIe-6594 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale+ FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe-6594 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Interface
R15-USB
Interface
Abaco Systems' R15-USB is the latest generation of performance and flexibility for MIL-STD-1553A/B Notice II using a high speed USB 2.0 interface with one or two dual-redundant MIL-STD-1553A/B Notice II/IV channels. Available in -40 to +75 temperatures (with relays) and ruggedized (without relays). The R15-USB includes advanced API (Application Programming Interface) software that reduces application development time..
-
Product
Pull-Thru Adapter, Wired, TriPaddle, For PXI-2564
510140235
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, for PXI-2564
-
Product
Sampling Scope Adapter
N5477A
Adapter Module
The N5477A sampling scope adapter makes the InfiniiMax III probing system fully compatible with the Infiniium 86100 DCA sampling scope family. With the N5477A, the DCA modules have 30 GHz of probing, increasing their performance and flexibility.
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
PCB Adapter, ITA, TriPaddle, 96 Position, To PCB-Mounted 1x96 Male DIN 41612 Connector
510108148
PCB Adapter
The 96 Pin ITA Signal Module is made from Ryton R-7, withstanding temperatures up to 220°C. Nomenclature is molded on the Module.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-02
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Serial Interface Device
Serial Interface
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PXI Express Interface
EMX-2500
Interface
The EMX-2500 is the industry’s first gigabit Ethernet LXI based PXI Express interface. This combines Ethernet's widespread usage and robust architecture with instrumentation-specific functionality, such as wired trigger bus and IEEE-1588-2008 synchronization, and extends it for use in PXI Express mainframes, making it an ideal solution for data acquisition applications.
