Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
Signal, Patchcord, Receiver, QuadraPaddle, 36", 24 AWG Twisted Pair, Single Ended
7-124424000-036
Signal Patchcord
Signal, Patchcord, Receiver, QuadraPaddle, 36", 24 AWG Twisted Pair, Single Ended.
-
Product
High-Voltage Differential Probe, 70 MHz
N2891A
High Current Probe
Use the N2891A 70-MHz high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2891A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to ±7000 V of differential and common mode voltage.
-
Product
G3 - 3 Module Solution
-
VPC’s G3 connector delivers unmatched versatility in a compact form, offering either high-current testing with dual 500+ Amp contacts or modular flexibility with three 90 Series modules. This footprint supports up to 672 signal contacts—plus options for high-speed digital, coax, power, fiber optics, and more—making it a powerful solution for evolving test environments.
-
Product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
-
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
Product
Mixed Signal Oscilloscope: 20 GHz, 4 Analog Plus 16 Digital Channels
MSOV204A
Oscilloscope
20 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
8 Channel Sample & Hold and Signal Conditioning Board for Group3
-
All channels provide for voltage division ahead of transient suppression before going into the S&H ICs. Channels that are sampled and held use a common sample and hold pulse that samples while high and holds while low. Jumpers on each S&H chip allow buffering of analog signals where sample and holds are not required. An advantage to the buffers is that it provides a high input impedance for high impedance voltage dividers.
-
Product
Electronic / Acoustic Signal Source
Bedrock BTB65 TalkBox
-
The Bedrock BTB65 Talkbox can be used as an electronic signal source by utilizing the line-out connection. Or it can be used as a calibrated acoustic signal source, due to its integrated loudspeaker. The Bedrock BTB65 Talkbox is designed to accurately play the STIPA test signal, as well as several other test signals. The device features an interactive LCD touchscreen to show,which allows you to easily control all features and monitor its settings at a glance.
-
Product
PXI 16 to 1 Mux 1Ghz 50Ohm SMA Connectors
40-747-521
Multiplexer Module
The 40-747 is a single 16 to 1 RF MUX available in 50 Ohmhm or 75 Ohmhm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohmhm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-747 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
Converter Signal Amplifier – 4…20 mA – DIN Rail
HD978TR3
-
Configurable converter signal amplifier with 4…20 mA (20…4mA). Input range -10 …+60mVdc.
-
Product
LXI WTB Adaptor, Thru line
60-982-001
-
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
Product
Analog Signal Conditioning &Isolation Products
DSCIA
-
DSCIA module is a signal channel isolated analog input or output.
-
Product
200 MS/sec RF/IF Rugged Portable Recorder
Talon RTR 2726A
-
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight: just less than 30 pounds- Shock-and-vibration resistant SSDs perform well in vehicles, ships and aircraft- 200 MHz 16-bit A/Ds- 800 MHz 16-bit D/As- 80 MHz record and playback signal bandwidths- Recording & playback of IF signals up to 700 MHz- Real-time sustained recording rates of up to 3.2 GB/sec- Windows® workstation with high-performance Intel® processor- Up to 30.7 TB of SSD storage to NTFS RAID solid state disk arraySystemFlow® GUI with signal viewer analysis tool- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 18-36 VDC power supply
-
Product
AS 857 AUTO SWITCHING TRANSMITTER
-
- Auto Switching to Secondary Input if Primary Signal Fail/Drops below -6dBm- Switches back to Primary Input when Primary Signal Reconnect/Improves above -4dBm- Input Signal Display of Active Input- AGC for both Input
-
Product
Serializer/Deserializers & Selector Muxes
-
Serializer/Deserializer muxes use both rising and falling edges of the clock to serialize the data from parallel inputs to serial output while demuxes deserialize the data from its serial input to parallel outputs. Selector muxes routes the differential inputs to either one or more of the desired outputs upon assertion of the appropriately selected port. Muxes can be used in various applications including High Data Rate Ethernet, Fiber Communication, Signal Routing and Broadband Test & Measurement Equipment.
-
Product
SignalShark® -Real-Time Remote Analyzer
-
Real-Time Remote Analyzer for the Detection, Analysis, Classification and Localization of RF Signals between 8 kHz and 8 GHz. Supports automatic direction finding and TDOA. Solves complex measurement and analysis tasks reliably and quickly with outstanding RF performance. Windows 10 based open platform for 3rd party applications. SignalShark exists in different incarnations. These are available as stand-alone units (table-top or in-system), single or double for installation in a 19" rack. The Remote Analyzer type is optimal for remote control applications.
-
Product
Dual Channel Dynamic Signal Analyzer
SR785
-
Stanford Research Systems, Inc.
The SR785 Two-Channel Dynamic Signal Analyzer is a precision, full-featured signal analyzer that offers state-of-the-art performance at a price that's less than half that of competitive analyzers
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 14-Bank 40GHz SMA-2.9
60-801-414
Microwave Multiplexer
The 60-801-414 is a 6-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
IP VIDEO MARGIN TESTER
IPMT-3
-
The IPMT-3 is a precision attenuator used to test IP video systems to insure that you have an adequate digital signal margin. Digital signal margin is the amount of signal level above the digital cliff that you have in your system to prevent a picture failure from occurring. IP cameras will give you a perfect picture until the network cable loss reaches beyond the minimum allowable signal level and then you suddenly get no picture at all. This effect is called the digital cliff, because like walking off of a cliff, everything is great till you take the last step off the edge and then all is lost.
-
Product
12-Bit PCI Express ADC/Digitizer
SIS1350
-
The SIS1350 is our first PC add on digitizer card. It was developed for high repetition rate acquisition of short analog signals (i.e. up to 128 µs at 500 MSPS) with good resolution
-
Product
Laser Diode Driver
S-101
-
LD Driver slot module of FOTS system is an efficient module that is user centered, which can drive various kinds of laser diode for the use of optical signal transmission or light source. The module has a built in LD socket, in which LD of 14 pin butterfly type is installed, which makes it possible for the user to change the LD he or she wants to drive when needed. It is leaded to get rid of the inefficiency of expense, at which various types of expensive united source module needed are purchased. By operating monitoring PD and high-performance processor that are installed inside the module, the output power and temperature of LD can be driven accurately and stably. The laser diodes can be modulated internally in square, sinusoidal, and triangular waves and its output power and temperature can also be maintained the level set by the user. In order to realize the various functions, the efficient and multi-functioned control programs with high speed processor, LCD monitor or GUI for remote control are available.
-
Product
SLSC RTIs
-
Rear Transition Interfaces (RTIs) are mounted at the rear side of the SLSC chassis as part of the backplane. The RTIs contact the signal and power connector of the SLSC card and provide a powerful and flexible solution to connect a wide range of industrial measurement equipment. The connectors and pinouts are designed to match the National Instruments (NI) standard. For this there is a wide choice of cables to connect the SLSC and the NI measurement units.
-
Product
Quad Linear FAN-IN FAN-OUT
V925
-
The Mod. V925 is a 1-unit VME module which houses three 4 In / 4 Out and one 3 In / 3 Out sections; one Discriminator channel is also featured. Each Fan in/Fan out section produces on all its output connectors, the sum of the signals fed to the inputs, eventually inverted.
-
Product
Sync Generator
LT4611
-
This product is a 1U full-rack size sync signal generator that outputs analog video sync signals and audio word-clock signals for broadcast stations. The external sync signal genlock function allows synchronized operation with input signals.The genlock function has a stay-in-sync function that maintains the phase when an error occurs in the input analog video sync signal. The dual power supply unit provides redundant operation. These features make it possible to configure a highly reliable system.Further, numerous options are available to allow GPS synchronization and PTP synchronization as well as arbitrary pattern output and digital audio output using 12G-SDI, 3G-SDI, HD-SDI, and SD-SDI. These options are designed to enable the management of the optimal synchronization system for your application.
-
Product
ABex Terminal Module for Göpel 1149Cx BSCAN Cards
ABex TM-1149Cx
-
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
Product
Programmable DC Power Supply
62000P
-
Chroma Systems Solutions, Inc.
Chroma’s Programmable DC Power Supplies 62000P Series offer many unique advantages for ATE integration and testing. Advantages include: constant power operating envelope, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations.
-
Product
ATI Performance Oscilloscopes
DPO70000SX
-
DPO70000SX ATI Performance Oscilloscopes deliver the industry’s most accurate capture of high-speed signal behavior to verify, validate and characterize your next generation designs. Capture up to 70 GHz signals with the lowest noise and highest fidelity, ensuring the most accurate measurements of your signal’s true characteristics.
-
Product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785598-02
FlexRIO Signal Generator
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, MCX
40-835A-101
Multiplexer Module
The 40-835A-101 (PXI) and 42-835A-101 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
USB-4431, 102.4 kS/s, 100 dB, 0.8 Hz AC/DC Coupled, 4-Input/1-Output Sound and Vibration Device
780164-01
Sound and Vibration
The USB-4431 is designed for sound and vibration measurements. Input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones. The four USB-4431 input channels simultaneously digitize input signals. The analog output (AO) channel is ideal for stimulus-response tests and can be synchronized to the AI channels.
-
Product
IO-Link Accessories/Connection Technology
-
- USB interface for connecting IO-Link enabled sensors to a PC- Bluetooth adapter for IO-Link sensors and masters- Repeater for increasing the range- Data splitter to integrate IO-Link sensors in old installations- Converter for converting standard signals to IO-Link and vice versa
