Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
CB-68LP, Low-Cost, Unshielded I/O Connector Block
777145-01
-
68-Pin Female VHDCI to 68-Pin Female Screw Terminal, Desktop Mount Terminal Block - The CB-68LP features 68 screw terminals for easy connection of field I/O signals to 68-pin NI data acquisition devices. It includes one 68-pin male SCSI connector for direct connection to 68-pin cables. This connector block features standoff feet for use on a desktop or mounted in a custom panel. The CB-68LP also has a vertical-mounted, 68-pin connector.
-
Product
MiniPCI Express 4-Way RF Combiner
SKU-089-13
-
MiniPCI Express 4-way RF Combiner. It allows combining signals from 4 antennas to a single antenna. The Adapter is a passive device and can be installed in any full size MiniPCI express circuit. This Adapter was designed for our Squid PCI express Carrier boards.
-
Product
AC-DC Wide Adjust Output Power Supplies
-
*Universal input.*Power Factor Correction.*Output Inhibit*Constant voltage and constant current modes.*Voltage and current monitor terminals.*Voltage and current programming capabilities.*Short circuit and overload protection.*Thermal protection.*Low Profile.*No minimum load required.*Adjustable down to 0 volts (‘Wide Adjust’ models).*Internal EMI Filter and RFI Shielding.*Pluggable connectors for input and control wiring.*Remote Sensing.*‘Vout OK’ signal monitor.*‘Soft start’ operation.
-
Product
Conformance Testing
Clarinet-TTCN SS7 ETS
-
Protocol: ITU-T Q703 standard defines protocol for Signaling System No. 7 – Message transfer part IUT: SS7 Signaling Point - MTP2-ITUATS: Based on ITU-T Q781 (07/96) test descriptions.
-
Product
Data Acquisition DAQ
-
Keysight Technologies has provided data acquisition (DAQ) and switching solutions for more than twenty-five years. We provide data acquisition solutions for electrical, physical, mechanical, acoustic and signal routing applications up to 50GHz.
-
Product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
Product
Light Source
UVM-SP-JW
-
Readouts of UV intensity and cumulative luminescence count are prompted either on the front panel or via the externally connected remote signal control. The UV intensity detection segment is intended to measure a specific intensity of light signals, while the cumulative luminescence count is designed to tally a cumulative count on all UV intensities measured, in conjunction with real-time calibration.
-
Product
DC-18GHz Modular Matrix
MS2010A
-
Universal Switching Corporation
Eliminating manual patch bays and patch cords, the System MS2010A is a compact high-performance modular switch matrix specifically designed for routing any coaxial signal within the DC-18GHz bandpass. Configurations are available from 4x4 to 12x12, and custom configurations are a simple to accomplish.
-
Product
G10x - 15 Module Solution
-
This 15 Module Solution provides reliability while simultaneously engaging up to 3,200 signal contacts. The adaptable G10x integrates a wide variety of I/O options in various module configurations. Contacts are incorporated into cable assemblies for specific instruments. The ITA has a unique, removable EMI shielded cover which allows easy access to enclosed modules and contacts.
-
Product
PXIe-4499, 204.8 kS/s, 114 dB, 4 Gains, AC/DC-Coupled, 16-Input PXI Sound and Vibration Module
781370-01
-
204.8 kS/s, 114 dB, 4 Gains, AC/DC-Coupled, 16-Input PXI Sound and Vibration Module - The PXIe‑4499 is designed for high‑channel‑count sound and vibration applications. With 24-bit analog inputs and IEPE constant current signal conditioning, the PXIe‑4499 is ideal for making precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. The PXIe‑4499 delivers simultaneous sample on all channels. In addition, the PXIe‑4499 includes built-in antialiasing filters that automatically adjust to your sample rate, software-selectable input gains, and TEDS smart sensor support for error-free setup. Common applications include noise, vibration, and harshness (NVH) analysis; large microphone arrays; and dynamic structural test.
-
Product
Amplifiers
-
Is an electronic device that can increase the power of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output.
-
Product
Input Devices
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic's Electromechanical Components are used to convert mechanical movement into electrical signals. These products, including switches, encoders, and potentiometers, are used in everyday devices at the point of user interaction.
-
Product
Anemometers
-
GAOTek offers an extensive selection of high quality, budget friendly and precise anemometers for purchase. Featuring fast response times, multi-function measurements as well as intelligent signal processing for maximum reliability and stability, GAOTek’s category of Anemometers provides users with the best anemometers of any type. Our Anemometers are available for purchase in the United States, Canada and globally.
-
Product
PCI-5154, 1 GHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
780320-03
-
1 GHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device - The PCI‑5154 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1 GHz of analog bandwidth and flexible measurement configurations.
-
Product
NI-9232, 3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
782000-02
-
3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9232 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9232 is also compatible with smart TEDS sensors. The NI‑9232 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Analog I/O
-
The AMAX-5000 analog I/O modules offers channel-independent configuration, signal type selection, and sensor wiring burn-out detection.
-
Product
PCIe Clocks: Time Signal Receiver For The PCI Express Bus
-
Meinberg Funkuhren GmbH & Co. KG
Although the PCI Express bus is software-compatible with other PCI implementations, the hardware of these PCIe plug-in cards is based on a different concept.Fewer lines are used for data transmission than, for example, with PCI plug-in cards - a high transmission rate is achieved by using a fast serial protocol.
-
Product
Optical Probes- High Bandwidth
DPO7OE
-
The DPO7OE series optical probes with a DPO70000 real-time scope deliver the performance and advanced debug capabilities designers need to fully troubleshoot 400G PAM4 signals, up to 56 GBaud, and reduce time to market.
-
Product
2.5GS/s 16Bit 2GS Mem 4CH 8 Markers AWG
P2584D
-
The Proteus P2584D, is a 2.5GS/s, four channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P2584D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 8-Channel, 2-Pole
40-614D-004
-
The 40-614D-004 (PXI) and 42-614D-004 (PXIe) 8-bank, 8-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Load Measuring Pins
-
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Product
Displacement Transducers - DC Operation
-
Columbia Research Laboratories
The Columbia DDCP Series Transducers are completely self-contained displacement measurement systems that operate from a low voltage DC power supply or battery. They permit highly accurate readout and recording of an output signal directly without auxiliary signal conditioning electronics.
-
Product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785584-02
-
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Atom-based Mission Computer System
ComSys-5361
-
The ComSys-5361 is a rugged COTS mission computer. Feature-packed and power stingy, a 12W Intel Atom CPU supports signal processing for critical applications. Highly configurable, application-specific I/O. Removable drive bay for two 2.5“ SSDs.
-
Product
Voltage Meter
MN3I
-
М-module МН3И is a mezzanine module designed to measure the instantaneous voltage value of high-frequency signals via 3 galvanically isolated channels from each other, control circuits and crate frame.
-
Product
Online Tone Generators
-
Output of our tone generators will be downloaded straight to your computer as a .wav file. In other words, our waveform generators will generate high quality sound files, but won't play them online, ensuring the highest sound quality one can obtain on a computer. Single Frequency: Sine Tone Generator, Square Tone Generator, Sawtooth Tone Generator, Triangle Tone Generator. Dual Frequency: Dual Sine Tone Generator (IMD Test). Variable Frequency (sweep) Audio Signal Generators: Sweep Tone (Chirp) Generator.
-
Product
Precision Programmable AC and DC Sources, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Tahoe Series
-
AMETEK Programmable Power, Inc.
The California Instruments Tahoe Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of-the art SiC power switching architecture and Digital Signal Processing, the Tahoe Series combines a robust, high-power AC/DC source with an advanced power analyzer in a single floor standing chassis.
-
Product
PCI-8511, 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-02
-
The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
LXI High-density 384x4, 2A Matrix
60-553-003
-
These high-density single pole LXI matrix modules are capable of switching up to 150VDC/100VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
LXI High Density 56x64 2A Matrix With BIRST
60-552-026
-
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
