Mixed Signal
Integrated circuit that handles both analog and digital signals.
See Also: Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed-Signal Test, Mixed Signal Testers, MIxed Signal Test Systems
-
Product
Signal Generator, 20MHz, 2 Channel, Arb.
33512B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
Video Signal Distributor
MSHM-305A Plus
-
MSHM-305A Plus, HDMI Distribution Amplifier, distributes three digital video input sources to the five output channels. The built-in amplification function enabled HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. It is also built-in CEC function according to current market request. User can select one (1) input source of the three and make sure connected condition with led of the front panel.
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Fiber-Optic/Copper Signal Adapters
-
Fiber-optic and copper signal adapters extend the functionality of Arbiter Systems® Timing and Frequency solutions. These products support conversions between fiber-optic and copper wire distribution networks. They may be used with Arbiter products as well as other third party devices.
-
Product
Signal Pylon Blocks
-
40 POL low resistance pylon, 40 POL signal pylon, 85 POL signal pylon, 102 POL Signal Pylon, 136 POL signal pylon, 170 POL low resistance pylon, 170 POL signal pylon, high current pylon blocks, optical pylon blocks, pneumatic pylon blocks, radio-frequency pylon block, & usb pylon blocks
-
Product
Rubidium Standard with Optional DDS Signal Generator
1450B
-
The 1450B outputs can be configured as sine waves or square waves and can provide frequencies of 10MHz, 1MHz, 100kHz, 1pps or optional signal generator outputs. The signal generator outputs use direct digital synthesizer (DDS) technology and are confirurable from 100Hz to 171MHz. The 1450B also includes a 1pps input that can be used to discipline and automatically calibrate the 1450B. The 1pps input signal is typically obtained from an external device like a GPS frequency receiver/antenna. The Novatech GPS1 Smart Antenna with 1pps output is available as an accessory to provide a complete turnkey solution.
-
Product
Digital Signal Processor
CHAMP-XD2M
-
Curtiss-Wright Defense Solutions
Imaging sensors, RADAR, and SIGINT provide an overwhelming amount of data that needs to be stored before it can even be processed, but current solutions offer far from enough memory to store it. By providing more memory capacity on a single board, systems can remain SWaP-C optimized and data can be connected and processed with ease.
-
Product
Digital ICP® - USB Signal Conditioner
-
The Digital ICP®-USB Signal Conditioner, Model 485B39, offers plug-and-play connectivity for your measurements. Model 485B39 from The Modal Shop, a wholly owned subsidiary of PCB Piezotronics, is a pocket-sized, dual-channel ICP to USB digital signal conditioner. The unit provides any ICP sensor – accelerometers, microphones, impact hammers, laser tachometers, and more – with a digital USB output. It is truly plug-and-play, with no drivers required. Digital ICP features two BNC inputs and a 24-bit USB digital signal output, allowing a direct connection from the sensor to any PC, tablet, or smartphone device for easy data collection, analysis, and sharing on-the-go.
-
Product
PXI FlexRIO Signal Generator
FlexRIO Signal Generator
The PXI FlexRIO Signal Generator combines analog I/O and a user-programmable FPGA into a single, customizable instrument. The instrument enables RF signal generation up to 2.9 GHz with 12 bits of resolution. The PXI FlexRIO Signal Generator uses FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. Using this instrument with NI-TClk, you can synchronize modules in one or more PXI chassis at up to picosecond‐level accuracy for high‐channel‐count applications.
-
Product
40GHz Four Channel MW Signal Generator 19" 1U Rack
LSX4094R
Signal Generator
The Lucid-X is a small footprint modular microwave signal generator that is available in multiple form factors, including Desktop, PXIe module, benchtop, rackmount, and portable. It has been designed to provide low phase noise, with a frequency range all the way up to 40GHz.
-
Product
Handheld Signal Level Meter
CT-DLM870D
-
The CT-DLM870D is a hand held signal level meter capable of reading analog, digital QAM and digital off air signal levels as well as Carrier to Noise, Bit Error Rate (BER), Modulation Error Rate (MER) and tilt.
-
Product
Satellite Signal Level Meter
Super Buddy 29
-
The Super Buddy 29 satellite meter has all of the great features of the standard Super Buddy satellite meter plus an internal combo 21 volt / 29 volt module to power the new DIRECTV SWM LNBs and the WildBlue / Telesat / Xplornet TRIAs! Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite.
-
Product
RF Signal Detector/Wireless Camera Detector
SH-055SRV / 10127
-
This "Wireless Camera Detector / RF Signal Detector / 2G Mobile Phone Detector" can detect the popular wireless CCTV camera, wireless phone, wireless tap and Cell phone from 50 MHz ~ 6.0 GHz.
-
Product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786853-01
Vector Signal Transceiver
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
-
Product
Optical Signal Conditioning Products
-
The single-mode fiber N7761A, N7762A and N7764A provide 1, 2 or 4 attenuation channels in a compact remote-controlled instrument. These attenuators provide very fast adjustment and have built-in output power monitoring for accurate power setting and control, as needed for receiver sensitivity testing or in system simulations.
-
Product
8 Channel Relay Board for Signal Isolation
FXA-104 Relay 8CH
Relay
The FXA-104 is a relay board to switch signals with 8 SPDT channels. It’s eight channels can be switched individually with a low active input. Each channel is equipped with a status led and capable of switching up to 2A. Due to its wide range input it’s very flexible to use and it is delivered with an installed DIN rail carrier.
-
Product
Signal Integrity Test Products
RoBAT RCI
-
*TDR & TDT, Measurement Capabilities*Impedance, Skew, Backdrill measurements*Automated Optical Inspection*DC Electrical Test*Now available with 4 heads*24 port (1 port per channel) TDR/TDT unit*Future capabilities – Fully automated VNA test (4 port S-Parameter Measurement)
-
Product
Video Signal Processors
-
Products that apply signal processing to convert, reformat, or optimize incoming video signals.
-
Product
Pulser Sensor, Sent Signal, CNEX/ATEX Certificates
SK-S
-
Beijing SANKI Petroleum Technology Co., Ltd.
*convert the mechanical transmission signal of flow meter into electrical pulse signal* send the electrical pulse signal to main-board to realize the metrology function of the flow meter
-
Product
Signal Amplifier
9100A
Amplifier
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Dynamic Signal Analysis Software
ObserVIEW
-
Vibration Research Corporation
View, edit, and analyze waveforms from recorded or live data. This powerful and efficient vibration analysis software package includes specialized modules for waveform recording and test generation.
-
Product
Signal Splitters
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a comprehensive portfolio of active multicouplers and bi-directional signal splitters for duplicating RF signals from common sources. The multi-couplers are designed in 50 ohm technology and are available as a 19 ", 1 U devices as well as slot-in modules for our 'Modular RF Systems' platform. With help of the slot-in modules, larger scale distribution structures can be realized in a space-saving and cost-effective manner. Some devices are available in variants for AC or DC power supply and provide service-friendly remote monitoring capabilities. For use in the production of infotainment components special multi-couplers with integrated HF and DC test functions are available. The multi couplers are used in applications like radio monitoring and direction finding, in product development, validation, manufacturing, quality assurance and in the field of research.
-
Product
High Mix Pick And Place
MC392
-
The dual-head MC392 pick & place machine is ideal for high-mix, low- to mid-volume manufacturing environments. It holds up 160 Smart Ports for tape and stick feeders, plus has space for cut tape strips and waffle trays, allowing more parts to be kept resident on the machine for faster job changeovers. High-quality components and a sturdy build achieve placement accuracy of 30 µm, 3 Sigma at placement rates reaching 6,400 cph.
-
Product
Signal Relays
-
Panasonic Industrial Devices Sales Company of America
Mechanical Relay ideal for signal control, etc., with less than 2A nominal switching capacity. Low Level current switching below 2A. Features include gold contacts, stable contact resistance, fully sealed construction, Form C contact arrangement, available latching and low operating power, and compact size for optimal board space usage. Applications include: AC Control, Communications, Security, Measurement Equipment, Audio Visual Devices, and Automotive.
-
Product
Satellite Signal Monitoring, Reference Solution
-
The Keysight Satellite Signal Monitoring, Reference Solution is a fast, effective solution for monitoring large blocks of spectrum combined with precise digital modulation analysis to validate satellite signal integrity up to 50 GHz. Built upon a modular instrument format (PXIe), its attributes include: excellent instrument density, expandable multi-channel support, and high data bus speeds, ideal for multi-band monitoring. To provide flexibility, a choice of vector signal analyzers (M9391A and M9393A) is available to tailor the system frequency ranges as needed.
-
Product
Signal Conditioners
General Purpose
-
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
Product
Satellite & Terrestrial Signal Combo Meter
Satlink WS-6909
-
Jointron(Quanzhou)Industry Co.,Limited
Satellite & Terrestrial Signal Combo Meter
-
Product
Signal Analysis
Cross-Spectrum FFT Analysis
-
The program Cross narrow-band spectrum is used for evaluation of the interrelation between the signals’ parameters obtained from the two primary transducers installed at various parts of the controlled object. This program can be used for detection of noise source location, for sound absorption level evaluation and the researched object acoustic properties control, for evaluation of space-time distribution of the directional energy flux (Poynting vector), for the ground cross-section FR characteristic evaluation (Nakamura method), etc.
-
Product
Narrow Band Digital Signal Delay Lines
-
Advanced Science and Novel Technology, Co., Inc.
Narrowband (11GHz-17GHz) tunable clock phase shifterDelay adjustment range of 140psExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the phase adjustment tuning portsIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with 800mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 0.91WFabricated in SiGe for high performance, yield, and reliabilityStandard MLF/QFN 24-pin package
