Production Test Systems
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
-
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
True Concurrent Test
TestStation Duo
-
The TestStation Duo is a true concurrent test system with independent test modules providing fast in-circuit test throughput and lowering high-volume production costs.It effectively doubles the test throughput of conventional in-circuit test systems, without doubling capital equipment costs or increasing manufacturing floor space, by combining two complete and independent test modules inside a single tester frame.
-
Product
Spring Clip Fixture
16092A
-
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
IFC Antennas & Radome Systems
-
System solutions providing inflight internet and live TV connectivity including satellite communications (SATCOM) systems, protective radome enclosures, antenna mounts, bird strike solutions, and adapter plates.
-
Product
Computing VITA System
CRS 48.5
-
The CRS 48.5 is a complete, integrated, pre-tested, ready-to-run HPEC rugged subsystem enabling faster development/deployment at lower cost and risk using the most advanced VITA 48.5 compliant air-flowthrough cooling to allow the integration of up to eight quad core Intel® Core™ i7 processing nodes.
-
Product
Magnetic Material Test Fixture
16454A
-
The 16454A is designed for accurate permeability measurements of toroidal-shaped magnetic materials. Since the construction of this fixture creates one turn around the toroid (with no magnetic flux leakage), the need of winding a wire around the toroid is unnecessary. Complex permeability is calculated from the inductance with and without the toroid. When the E4991A/4291B with option 002 is used as the measurement instrument, direct readouts of complex permeability are possible. In addition, it is furnished with a small and a large fixture to adapt to a wide range of sizes.
-
Product
6TL60 Rotary Test Handler
H79006010
-
6TL60 has been designed according to the 6TL philosophy, following the concepts of flexibility, modularity and scalability, and with the aim of improving production efficiency as well as increase production capacity and reduce costs.The 6TL60 is the best production solution to automate test processes to reduce the cycle time and the footprint used in the manufacturing plan
-
Product
Wireless Device Test
-
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
Product
Test System Optimized for High-Performance Digital and SoC
ULTRAWAVEMX44 and ULTRAWAVEMX20-D16
-
Teradyne is the leader in RF/wireless device testing and has a large installed base of UltraFLEX test systems with the UltraWave24 RF instrument. As new devices for handset and base station applications are introduced using mmWave technology, Teradyne’s mmWave instrumentation has expanded in anticipation of new testing demands.
-
Product
Functional Test
xUTS
-
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
-
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
Test System Optimized for High Volume Production Testing of Integrated Circuits
ETS-364 / ETS-600
-
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture. The test system offers separate floating resources for each site, improving site isolation and measurement accuracy coupled with digital instrumentation enabling the most efficient, high-volume testing available. The system supports up to 240 analog pin channels, and offers 133 MVPS digital vector rate with up to 128 digital pin channels. Eagle's scalability includes the ability to double the capacity of an ETS-364, providing more than 480 analog pin channels and up to 256 digital I/O pin channels with the ETS-600.
-
Product
Mezzanine System Carrier
MMS6245
-
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
Product
SoC/Analog Test System
3650-S2
-
The Chroma 3650-S2 is specifically designed for high-throughput and high-parallel testing to provide the most cost-effective solution for fabless, IDM and testing houses.
-
Product
NI Real-Time Test Cell Reference System
780590-35
-
VeriStand Full Development License with NI Standard Service , Include 1 Year SSP
-
Product
Advanced SoC Test System
3680
-
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
Product
Environmental Control System Test Platform
-
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
Product
Bottom Electrode SMD Test Fixture
16197A
-
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Test Fixture Kits
-
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
Product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
-
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
Product
Automotive Electronics Functional Test System
TS-5020
-
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
Product
Valve Leak Measurement System
VLMS
-
The G Systems Valve Leak Measurement System (VLMS) reliably measures slow leaks that are unidentifiable with conventional leak detectors, helping manufacturers test and ensure that critical valves are absolutely airtight.
-
Product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
-
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
-
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
Product
Mezzanine System
3560
-
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
Product
Wireless Test Standards Software
-
Generate and analyze signals for cellular and connectivity standards with NI PXI RF instrumentationPerform advanced automated test with the easy-to-use NI-RFmx software APISave on all NI RF wireless test software under a single license
-
Product
VXI Digital Multiplier
4152A
-
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
-
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
Dielectric Material Test Fixture
16453A
-
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
-
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
