Very Fast Transmission Line Pulse
tests simulate IC or SOC ESD events with pulse lengths < 10ns and deep sub nanosecond rise times. Also known as: VF-TLP
See Also: Transmission Line Pulse, TLP
-
Product
DMX Line Tester
DMXTSTR
-
The DMX Line Tester instantly displays the presence of +/- data on DMX lines and feed-through connectors. It serves as a perfect pocket sized tool for troubleshooting DMX512 cabling.
-
Product
Pulse & Delay Generators
-
The benchtop pulse generators feature a fast risetime and low jitter. Our most popular digital delay pulse series 575 and 577 generators are now available with selectable time references. With up to eight channels of delay and width control, each individual channel's reference can be set either to the trigger or to any other channel. So look below if you require a picosecond pulse generator or nanosecond pulse generator for your application.
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 271
-
FEATURES: Full Duplex to 56 KBPS; 2 Kilometers on 62/125 Fiber; Total Electrical Isolation; Eliminates Noise Problems; ST Connectors; No Power Required. The Model 271 provides feature packed performance and reliability for data transmission over glass fiber.
-
Product
AC Power Line EMI Filters
CleanSweep®
-
CleanSweep® filters block EMI on power lines (both common and differential modes) and, uniquely, in ground, from reaching sensitive equipment. They also reduce EMI "backflow" from a "noisy" source that otherwise would end up on your AC power network.
-
Product
Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Rotating Type)
HR-200RT
-
HR-200RT is connected to a residual chlorine sensor (RA-30), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents.Stable measurement over a long period was realized by physical polishing cleaning using beads.
-
Product
Medium & High Voltage Pulse Generators (Rise Time > 1 ns)
-
Offer fast medium voltage pulsing with high current capability. These models are ideal for driving solenoids, pulse testing of MOSFETs, and other applications.
-
Product
End of Line Test System for Automotive Seats
AS519
-
AS519 is specifically designed to perform ECU’s EOL tests in the automotive industry. It integrates a programmable power supply up to 20V 20A with high reading resolution. Interaction with the DUT is established through CAN bus by an interphase adapter in a USB port of the test managing computer.
-
Product
Platiunum Tools TelScope Telecommunication Line Analyzer Test Set
#TLA300-1
-
The TLA300-1 TelScop is a telecommunication line analyzer for POTS butt sets.
-
Product
- RS-232 High Speed Line Driver with LCD Display
Model 227
-
FEATURES: DataSpy Status Display; Full Duplex to 5 Miles; Async, DC to 115.2 KBPS; Powered by TD; RJ-11 and Screw Terminals for the Line Interface; Built-in Surge Protection; Fully Compatible with Model 201 up to 19.2 K. The Model 227 RS-232 High Speed Line Driver with LCD Display provides full-duplex transmission from DC to 115.2 KBPS over two twisted pairs.
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 9271
-
The Model 9271 RS-232 Fiber Optic Auto Powered Line Driver features a standard DB9 interface for maximum performance and reliability of data transmission over glass fiber, eliminating the need for serial to nine-pin adapters. In addition, it brings effective data communications to manufacturing environments. I
-
Product
Tabletop Light Fastness Tester
TF419
-
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
Product
Logger version optical fast DO sensor
RINKO I / I D
-
Rinko I is an autonomously deployable data logger with a fast response optical DO sensor. The instrument and the software with various operating mode offer flexible observations in the field. The small-sized and the self-contained unit with batteries and a data logger can be easily integrated on platforms (e.g. CTDs). Rinko ID has a depth sensor, allowing for DO vertical distribution measurements.
-
-
Product
PXIe Precision Source/Measure Unit, 15 MSa/s, 100 FA, 60 V, 3.5 A DC/10.5 A Pulse
M9603A
-
The Keysight M9603A is a PXIe precision SMU featuring best-in-their-class narrow pulse width as narrow as 10 μs. It enables dynamic/pulsed measurements with up to 15 MSa/s for broad emerging applications such as VCSEL optical devices.
-
Product
Dielectric Loss Tangent and Transmission Attenuation Measurement System
RTS03
-
RTS03 measures relative permittivity (dielectric constant), dielectric loss tangent in the frequency range between 5GHz and 26.5GHz based on a correlation between measurement frequency and transmission attenuation as the microwave passes through the flat plane sample.
-
Product
PXI/PXIe Very High Density Multiplexer, 24-Channel, 8-Pole
40-675B-002-24/8
-
The 40-675B-002-24/8 (PXI) and the 42-675B-002-24/8 (PXIe) are 24-channel, 8-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
Product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
-
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
Product
Fast USB Strain Module
FSU-SSB
-
The FSU-SSB is a fast, compact, high precision strain bridge input module delivering high resolution readings over USB and communicated directly to a PC. It is aimed at dynamic applications that require high speed measurement.It delivers high speed measurements of 4800 samples per second at 13 bits noise free resolutio
-
Product
SparkFun Line Sensor Breakout
QRE1113 (Digital)
-
This version of the QRE1113 breakout board features a digital output, using a capacitor discharge circuit to measure the amount of reflection. This tiny board is perfect for line sensing when only digital I/O is available, and can be used in both 3.3V and 5V systems.
-
Product
Pulse Generators
-
Active Technologies Pulse Generators can be used to set up continuous or triggered pulse streams and offers flexibility to address the most challenging applications like big physics, automated testing, microwaves, modulators, wireless communication, medical and chemistry.
-
Product
PCI Pulse Position Data Communication Board
MS 1708
-
*Bus Interface - PCI Bus*Micro controller Based Design*Shared Memory for Communication*8 Channels RS422 / Modified RS422*PPD (Pulse Position Data) Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS*Independent Intelligent Devices for RS422 and PPT Communication
-
Product
Pulse Generators
Split Collar Pulser Wraps
-
Pulser wraps clamp around a rotating shaft and work with Electro-Sensors shaft speed sensors and are an ideal solution for installations where the end of the shaft is inaccessible. The two halves fasten together around the monitored shaft with recessed Allen head socket screws (provided). Standard and custom models accommodate any shaft diameter, tight spaces, and keyways.• Standard wraps operate to 3,000 rpm (high-speed also available)• Standard wraps available in PVC, aluminum, or stainless steel
-
Product
PCI Very High Density Multiplexer, 49-Channel, 4-Pole
50-670C-022-49/4
-
The 50-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
150 A, 10 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 2 meter cable
CP150B
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Programmable Delay Line Instrument
XR-100
-
The XR-100 is designed to give you our broadest signal delay range as well as superior switching speeds
-
Product
Electro Optical Terahertz Pulse Reflectometry
EOTPR 3000
-
The EOTPR 3000 system is configured with a manual probe station to meet today’s tough FA environment which requires to isolate fault location in minutes rather than hours or days, while maintaining the EOTPR’s world leading sub-5 μm fault isolation accuracy.
-
Product
PXI/PXIe Very High Density Multiplexer, 10-Channel, 16-Pole
40-675B-002-10/16
-
The 40-675B-002-10/16 (PXI) and the 42-675B-002-10/16 (PXIe) are 10-channel, 16-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. They use high quality electromechanical signal relays allowing each channel to switch current up to 1 A at 150 VDC/100 VAC. Connections are made via a front panel 200-pin connector.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Pulsed And CW EPR/ESR: Synthesizers Up To 280 GHz
-
Insight Product Company offers synthesizers at frequencies from 30 to 280 GHz which can be used in EPR/ ESR experiments. These sythnesizers are designed to go swiftly from the generation to the non-generation mode and back. This process is controlled by external TTL signal. There is also the possibility to manipulate the phase, namely to shift it by 90 degrees and 180 degrees. ON/OFF switch time is approximately 2 nanoseconds.
-
Product
Absorber Lined Shielding Enclosure Measurements
ALSE
-
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
