Y.1564
Ethernet service activation test methodology.
-
product
LXI Chassis Y Plugin - Y9 Y16 - Multi-Y Connection
65-110-104
This Y9 Y16 plugin is for the 65-110A chassis. One of these plugins are required to be fitted to configurations of the 65-110A chassis assembly with 16 Y input connections.
-
product
Fully Automatic Test Machine for Ceramic Substrates
U800CCT
1. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Automatic loading and unloading of magazine5. Automatic bad marking and verification of scratches
-
product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 75Ω, MCX
42-837A-101
The 40-837A-101 (PXI) and 42-837A-101 (PXIe) are 75Ω 2x2 RF matrices with 1 bank in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
product
IO-Link Sensors for Motion Control
Encoder for precise position determination and linear measurement, Defined pulse sequence for the reliable detection of rotational speeds, Inclination sensors for precise measurement of angles of inclination on X and Y axes, High measurement accuracy across the total angular range in two axes, High protection rating for the requirements of harsh industrial environments
-
product
LXI 2.4GHz 50ohm 24x8 Matrix
60-771-002
The 60-771 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 8 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
product
Custom Extensometers
Jinan Testing Equipment IE Corporation
Special biaxial extensometer for limiting dome height bulge tester for sheet metal formability testing. Simultaneous X and Y strain measurements are taken.
-
product
Laser Scanning Microscopes
A confocal laser scanning microscope scans a sample sequentially point by point, or multiple points at once. The pixel information is assembled into an image. As a result you acquire optical sections with high contrast and high resolution in x, y and z .
-
product
Grypper "Y"
Ironwood Electronics Grypper Y contact is design to work with BGA devices with solder balls/bumps with no equator or small exposure where the standard Grypper cannot reliably hold on to the solder ball. The Y shape, working with the sliding lid, allows reliable contact and ensures device retention in high vibration application. Lower forces, <25 grams, makes insertion easier too and the less aggressive contacting allows 40+ insertions of the same device. The Sliding Lid can be configured to include heat sinking. The Y contact designs cover BGA devices from 0.35mm pitch and larger and the short electrical length has superior electrical performance.
-
product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 50Ω, MCX
42-877A-101
The 40-877A-101 (PXI) and 42-877A-101 (PXIe) are 50Ω 2x2 RF matrices with 1 bank in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
PXI Single 8x2 1-Pole 10A Power Matrix
40-551-002
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 75Ω, MCX
40-837A-101
The 40-837A-101 (PXI) and 42-837A-101 (PXIe) are 75Ω 2x2 RF matrices with 1 bank in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, SMB
40-877A-002
The 40-877A-002 (PXI) and 42-877A-002 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
Analytical Gear Inspection Machine for Workpieces Up to Ø 6,000 mm
KNM X series
machine structure with outstanding intrinsic accuracylarge bearing distances of guidesinherently stable granite machine base on active dampers to absorb vibrations ? no foundation requireddrive system close to center of gravitylinear motors in X-, Y-, Z- measuring axeshigh precision air- or hydrostatic bearing rotary tables (diameters from 500 to 1,800 mm) with direct drive and through holemotorized positioning of measuring column (V-axis) to the actual workpiece diameterlaser based system for safe operation
-
product
EZ-Slider Torque Arms
The EZ-Slider torque arm is crafted with a lightweight durable carbon fiber, the arm offers X & Y axis mobility. It provides the freedom to travel side-to-side and up & down on a production floor. An ideal ergonomic solution for multi-tool applications such as a moving production and assembly line where balancers are fixed to a trolley system. Eliminates torque reaction of assembly tools. Can be used with a variety of assembly tools like angle nutrunners and electric & pneumatic screwdrivers.
-
product
LXI Reed Relay Matrix - Dual 32x16 Plugin, No Direct Y Access, 3 Analog Buses
65-225-101
These Modular LXI Matrix Reed Relay Matrix Modules plug into our LXI Modular Chassis (model 65-200-002)—providing access to all signal connection on 200 pin connectors. They are constructed using Pickering Electronics' Reed Relays offering maximum performance and reliability as well as very fast operate times.
-
product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
product
Spectroradiometer
Spectroradiometer is usually used with a integrating sphere to measure the photometric and colorimetric parameters of all kinds of lamps. Relative spectral power distribution P(λ), chromaticity coordinate (x,y), (u,v), correlated color temperature Tc, color rendering index Ra, dominant wavelength, peak wavelength, spectral bandwidth, color purity, color ratio, SDCM, luminous flux, etc.
-
product
Spring loaded type sample mounting board
SPCB
Mount samples on SPCB board without bonding wires.Spring loaded clamps helps to move probe pin easily x, y, z direction.Gold plated Non-magnetic phosphor-bronze constructionContacts on sample’s four point corner by soldering materials, such as InSn may still be required for good ohmic contact.
-
product
Digital Colorimeter & Illuminance Meter
CHC-I
This Digital Color Meter & Illuminance Meter is based on all digital integral photometric and colorimetric measurement technology. It has no analogue unit, thus it is very simple to overcome the zero drift which is impossible to be avoided in current colorimeter. The digital X (λ), Y (λ), Z (λ) sensor has large dynamic range so that there is no range-changing error in it; moreover, it possesses strong anti-interference ability and high accuracy. The CHC-I contains internal RS232 computer interface, the calibration is done by software. It is suitable for monitoring and remote applications. The CHC-I software can calibrate the instrumentation, sample the data through RS232 interface and print out the results. It can also be calibrated by other standard light sources to obtain very high measuring accuracy of x, y color coordinate and color temperature. It is a real-time measuring system and run under Windows System. 128*64 lattice LCD display, RS232 computer interface and software, Data hold function.
-
product
Legacy Liquid Detection Rope Sensor
ENVIROMUX-LDSx-y
For warning of flooding. Detects liquid depth >0.1" (2.5 mm). Minimum puddle: 0.6" (15 mm) diameter. 100% waterproof electronics. Detects any liquid or moisture, except deionized water. RJ45 connector. Voltage Supply: 12VDC. Current Consumption: 20mA. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Available water sensor cable (x) lengths: 1/10/50/100/200/400/600/800/1000 feet. Plenum rating: CL2P (UL). Available 2-wire cable (y) lengths: 5/10/20/50/100 feet. Powered by ENVIROMUX-SEMS-16U and SERIMUX-S-x. Regulatory approvals: CE, RoHS. Requires the ENVIROMUX-SEMS-16U and SERIMUX-S-x to operate. Use self-adhesive clips (ENVIROMUX-CLP10-LD) to prevent sensor rope cable from shifing after installation. ENVIROMUX-CLP10-LD includes 10 clips.
-
product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 50Ω, SMB
42-877A-002
The 40-877A-002 (PXI) and 42-877A-002 (PXIe) are 50Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-877A modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
Spinstand Automation For Media Testing With XY-Positioning
V2002
Guzik V2002 XY-positioning spinstand uses the X and Y coarse positioning stages actuated by linear motors and the micro-positioning stage actuated by the piezo element aligned with X coordinate axis to place the tested head on the specified track. WITE32 software converts the requested track number and skew angle into X and Y coordinates.
-
product
PXI/PXIe RF Matrix, Dual 2x2, 2.5GHz, 75Ω, MCX
42-837A-102
The 40-837A-102 (PXI) and 42-837A-102 are 75Ω 2x2 RF matrices with 2 banks in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
product
LXI High Density 32x64 2A Matrix with BIRST
60-552-023
It is constructed from 8x64 sub-assemblies, permitting the matrix to be supplied in a variety of sizes from a single 16 x 64 to 64 X 64 and dual 8x64 to 32x64. Larger configurations can be easily achieved by utilizing the Loop thru connections on either the X or Y bus, for instance, four 64x64 units can be linked to create a 128x128 matrix.
-
product
LED Tester For Ultra High Power
Electrical Testing: Forward：VF、DVF、VFD、IF、DIF Reverse：VZ、DVZ、IR、DIR AC：VAC、IAC、WAC、PFOptical Testing: can test LOP in cd/mcd/W/mW/lm... from different optical components Wavelength λp,λd,λc,hw,purity,(x,y),CCT,CRIFour-wire measurement and contact resistance in case of deviation. Auto polarity identification and preheat function.Compatible mechanical interface.Optional ESD static test system.
-
product
Spectrometer & Colorimeter
Spectroradiometer is widely used to measure the spectral, photometric and colorimetric parameters of all kinds of lighting sources which usually include relative spectral power distribution P(λ), chromaticity coordinate (x,y), (u,v), correlated color temperature(CCT), color rendering index(CRI), dominant wavelength, peak wavelength, spectral bandwidth, color purity, color ratio, luminous flux, Illuminance, luminance, spectral transmittance and reflectance, etc. PIMACS provides different types of spectroradiometers and colorimeter to meet the requirements in laboratories or on production lines. They are applied in the measurement for general light sources, LED & OLED products, displays, etc.
-
product
LXI 50Ω RF Matrix - 2.4GHz
Pickering's LXI 50Ω RF Matrix - 2.4GHz design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output. These matrices can be supplied in a variety of configurations based on Y axis sizes of 4, 8 and 16 and X axis sizes up to 32. The smaller matrix sizes in the range are factory reconfigurable up to the maximum size.
-
product
PXI Dual 2x2 RF Matrix 2.5GHz 50 MCX
40-877-102
The 40-877-102 is a 50Ω 2x2 RF matrix with 2 banks in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-877 modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
product
Photon Counting Cameras
Photek photon-counting camera systems are unique as they provide the ability to capture and integrate an image in real time. These systems are ideal for extremely low photon emission applications such as bio-luminescence, chemi-luminescence and weak fluorescence. The ability to accurately analyze transient events is a key feature of this product. The length of time that the image can be integrated is limited only by disc space, and allows the user to fully capture real-time events. X, Y and time co-ordinates for post acquisition analysis is also recorded. X-ray and vacuum imaging camera options are also available.
