Charge Amplifiers
A high-gain voltage amplifier with negative, capacitive feedback for converting a charge into a low impedance output voltage.
-
Product
RF POWER AMPLIFIERS
BSA Series
-
RF Input:N-f, standard on rear panelRF Output:standard on rear panel<1 kWN-f<3 kW7-16-f<5 kWEIA 1 5/8Mains Supply:Line Power:<1000 VA100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter:via status displayAmbient Temperature:0 ... +45 °CStorage Temperature:-20 ... +85 °CRelative Humidity:up to 95% (non-condensing)Operating Altitude:up to 2000 m above sea levelVibration and Shock:MIL-STD-810 GCooling:forced air with integral blowerair intake from front, air exhaust at rear
-
Product
IRIG Amplitude Modulated Time Code Distribution Amplifier
1205A / 1205A-MC
-
Precise Time and Frequency, Inc.
The ptf 1205A is a 12-channel IRIG amplitude modulated time code distribution amplifier housed in a 1U high, 19″ rack package. The ptf 1205A uses an RF design combining the latest technology in low noise components to minimize input/output delays which are of the order of nano seconds.The unit uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
Ultra-low Noise High Voltage Amplifier
WMA-200
-
The Falco Systems WMA-200 model is a high quality, high voltage, linear laboratory amplifier optimized for experiments requiring world-class, ultra-low output noise. The excellent noise performance, combined with the wide bandwidth and large voltage range make this amplifier the preferred choice for the most demanding precision positioning systems. The amplifier will routinely enable sub-atomic positioning resolution with piezo positioning systems and MEMS devices. Two WMA-200 amplifiers and a WMA-IB-LN phase inverter - buffer can be used to double the output voltage.
-
Product
Hybrid Amplifiers
Limiting
-
Macom Technology Solutions Holdings Inc.
MACOM offers a complete line of RF and microwave limiting amplifiers. Our limiting amplifiers use the latest thin film hybrid manufacturing techniques to obtain the highest level of performance, repeatability, and reliability. MACOMs portfolio of amplifiers range from 10 MHz to 4 GHz and are ideally suited for hi-reliability and mission critical applications.
-
Product
Smart Refrigerant Charging Kit
HUB4
-
UEi Test & Measurement Instruments
The HUB4 gives the ability to wirelessly get Vapor and Liquid pressures via the WPP1 probes and Vapor and Liquid temperatures via the WPC1 probes, all via the free UEi Hub App. Easy to use and a rugged design make the App and probes an excellent addition to any technician's toolbox.
-
Product
Solid State Broadband High Power Amplifier
Model 2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
Product
Amplifier Dyno
AD-1
-
The AD-1 Amplifier Dyno is a tool that is designed to be used any place an amplifier exists. It can be used in a lab or production line to test true amplifier power output, quickly and easily. It is simple menu driven, does not require a computer, and cannot be cheated as the load banks are internal. It can be used in an automotive audio install shop to test true amplifier output while the amplifier is installed in the customer's vehicle.
-
Product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
-
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
CATV Multi-ports Output High Power Full Function Optical Amplifier Module
HHOA-F5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HHOA-F5000 series is a kind of multi-port output, high power, full-function optical amplifier module and is suitable for CATV with low noise. Its total output power is 27~40dBm (0.5W~10W) optional and its optical output port can reach to 64 pieces at most. The module has standard RS232 interface, adopts high reliable and low power consumption design as well as adopts APC, AGC control mode. The product has two series: The output power of Huatai HHOA-F5000 high power optical amplifier module can be chosen in the range of 27dBm~40dBm. According to different output power, Huatai HHOA-F5000 adopts two latest technical solutions. One is to use single mode high power 980nm pump laser with cooling and EDF, multi-pump synthesis technique. The other is to use multi-mode high power 980nm pump laser without cooling and double-clad Er-Yb doped fiber-optic technology. It provide a whole set of high reliability, low cost, low noise and low power consumption solutions for the application of high power, multi-port output amplifier. It can be widely used in CATV head-end or FTTx distribution network.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
LT Range Broadband Power Amplifiers 20 MHZ - 1000 MHZ
LT Series
-
Class A solid stateBroadband (instantaneous single band): 20 MHz 1000 MHzTypical output power : 90 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 60 W and H < -20 dBc from 20 MHz to 80 MHz andP1dB > 75 W and H < -20 dBc from 80 MHz to 500 MHz andP1dB > 45 W and H < -20 dBc from 500 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to LT 160 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
Product
8-Channel Amplifier and Low-Pass Filter Module
SCS-816
-
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
Product
3-Ch Sensor Amplifier
PS-1300
-
The PS-1300 3-Ch Sensor Amplifier is designed to be compact and light weight, and able to be used in combination with a tri-axial accelerometer. Each channel can also be used independently and connected with a single axis accelerometer. The PS-1300 has built-in integration function and enables to optimize the input signal to vibration data analysis devices connected.
-
Product
Bi-Directional Amplifier
-
RF Lambda’s bi-directional amplifiers can be used in repeater type applications where a single conductor is used for both receive and transmit. These amplifiers offer low noise figure and high linearity. Hermetically sealed options are available upon request.
-
Product
Portable Charging Facility Testing Platform For Electrical Vehicle
-
PONOVO has long-term follow-up technology in China and abroad. Based on its own mature intelligent power detection equipment, and according to its own advantages in the field of new energy, PONOVO could be able to provide users with professional new energy test system solutions.
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800B (2RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800B (2RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
High-Voltage Amplifier
ZET 420
-
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
Product
Low Frequency Active Antenna And Amplifier
Type NLF-2
-
A Hot, Active, Noise Reducing Antenna System that will sit on your desk and copy 2200, 1700, and 600 through 160 Meter Experimental and Amateur Radio Signals!
-
Product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3
-
The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
Product
Amplified Noise Modules
NC1000 Series
-
The NC1000 Series amplified noise modules produce AWGN as high as +13 dBm, and have bandwidths up to 10 GHz. The high power modules are designed to test noise immunity for Cable TV equipment, secure communication channels, and military jamming systems. The lower power modules, <= 0 dBm, are random jitter sources for many applications including, PCIexpress, Infiniband, and 10 GigE.
-
Product
Amplifiers
-
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
Product
CATV Booster Optical Amplifier
HA5100
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Product
Driver Amplifiers (< 3 W)
-
Qorvo's driver amplifiers are designed to provide good linear or efficiency performance for gain stages prior to the final power amplifier in a transmitter chain. These products support frequencies up to 46 GHz, using process technologies such as InGaP HBT, power pHEMT, E/D pHEMT and GaN.
-
Product
Solid-State High Power Amplifier 18 - 26.5 GHz
AMP4065LC-2
-
Exodus Advanced Communications
Designed for EMI/RFI, lab, and general communication applications. Exodus Broadband SSPA product feature GaN, GaAsFET discrete and Chip & Wire Hybrid technologies covering one octave through decades frequency ranges from Operating Frequency Range 18.0-26.5 GHz.
-
Product
RF Amplifier
SA812AGC
-
Hangzhou Softel Optic Co., Ltd.
SA812AGC Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800C (3RU)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800C (3RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
Product
Single-Ended to Differential Amplifiers
-
Analog Devices has developed a broad portfolio of single-ended to differential amplifiers that help designers meet their high performance requirements. ADI single-ended to differential amplifiers enable the processing of both single-ended inputs to complementary differential outputs or differential inputs to differential outputs. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single-ended output.
