Compression
the result of being pressed.
See Also: Force, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic, Crush, Extensometers, Bending
-
Product
Real-Time Video Acquisition and Compression Board
Aexeon Quattro
-
Aexeon Quattro is a low-cost, real-time video acquisition and compression board for applications where multiple video streams are needed. Available in either PCI or PCI Express formats, Aexeon Quattro incorporates a digital media processor and on-board frame buffer for reliable capture for the most demanding application. Aexeon Quattro contains four independent full-resolution video channels capable of simultaneous streaming of real-time video to system memory or display. Aexeon Quattro also comes equipped with all the necessary I/O control to make application development easy.
-
Product
ARINC 818 Recorder
-
ARINC 818 Digital Video Recorder powered by Xilinx Zynq Ultrascale+ MPSoC device, is a multi-channel record/playback system that accepts any form of ARINC 818 video input with different resolution & refresh rates. The received ARINC 818 video stream is encoded with the assist of an on-chip H.264/H.265 video codec engine which is capable of performing simultaneous compression and decompression of video streams. Finally, the encoded video is stored in SSD hard drive.
-
Product
Analog DVR
-
Sylo Vision Technology Co., Limited
Security cameras capture an analog video signal and transfer that signal over coax cable to the Digital Video Recorder (DVR). Each camera may be powered by plugging in the power supply right at the camera or by using RG59 Siamese cable which bundles the video and the power cables. The DVR converts the analog signal to digital, compresses it, and then stores it on a hard drive for later retrieval. Intelligence is built into the DVR to handle such things as scheduling, motion detection, and digital zoom. Monitors for viewing the video are connected to the DVR, or it can be set up to publish over an internal network for viewing on PCs. The DVR can also be set up to broadcast over the Internet and can add password protection and other features. When broadcasting over the Internet, the video for all of the cameras is transmitted as one stream (one IP address). Therefore, it is very efficient.
-
Product
Single Space Electro-hydraulic Servo Universal Testing Machine
WAW-F Series
-
Jinan Testing Equipment IE Corporation
WAW-F series single space Servo-Hydraulic Testing System Computerized is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The ultra-large testing space & dual-action actuator with longer stroke enable it to test not only standard specimen, but also longer ones with long elongation every so often. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing System Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Tester of Single Space is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
Concrete Comprission Testing Machine
CONCRETO 2000X/3000X
-
CONCRETO Series This compression testing machine can safely and efficiently perform tests at a high capacity without causing explosive fracture (failure of the specimen) on ultra-high-strength concrete, which is used as a structural material in high-rise buildings, etc. This one machine can be used for materials ranging from ultra-highstrength concrete to specimens that have been recently cast, mortar, etc.
-
Product
75 Ohm BNC Connectors
-
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
-
Product
Process Instruments
-
The use of clean, compressed air as a medium to operate, control, and transmit signals to pneumatic instruments like valves, transmitters, and controllers
-
Product
Low Gauge Vacuum Tester
G4103
-
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
Product
USRP Software Defined Radio Stand-Alone Device
-
The USRP Software Defined Radio Stand-Alone Device consists of an onboard processor, FPGA, and RF front end. You can program this device using either LabVIEW Communications System Design Suite or an open-source software workflow, depending on the operating system you choose. You can provision the device with NI Linux Real-Time, Linux Fedora, or Linux Ubuntu real-time operating systems. The USRP Software Defined Radio Stand-Alone Device enables you to prototype a range of advanced research applications such as stand-alone LTE or 802.11 device emulation; Medium Access Control (MAC) algorithm development; multiple input, multiple output (MIMO); heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding.The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Single Screw Electromechanical Universal Testing Machine
CMT Series
-
Jinan Testing Equipment IE Corporation
The CMT series single screw testing machine is designed for mechanical property test mainly on metal materials, cement, asphalt, and bitumen etc. A variety of fixtures can be offered to do compression, bending and shearing test as well. This series of single screw testing machine is suitable for the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many fields such as industry factories, mineral enterprise and high schools.
-
Product
Material Testing Software
MS100
-
Sinowon Innovation Metrology Manufacture Ltd.
MS100 is professional software for material testing in windows system, it is able to conduct tensile, compression, bending, shearing, bonding strength, peeling, tearing and other tests for rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials.
-
Product
Compression Test Machines
-
Infinity Machine International Inc.
Compression Test Machines by Infinity Machine International Inc. - for applications such as: baby carriages and strollers durability tester, compressive strength testing machine, tensile testing machine, extrusion compression test equipment for small consumer electronics, paper bursting/crushing compressive strength testing machine, pneumatic springs compressive strength testing machine durability, and more.
-
-
Product
Compression Testing Machine for Special Purposes
-
Jinan Testing Equipment IE Corporation
These compression testing machined are suitable for testing the compression strength of components or structural material such as concrete, steel, brick, rubber pad, etc. These compression testing machines feature large test space and double actions. Hand operate, analog dial or monitor. Hydraulic servo with computer control.
-
Product
500KG MicrocomputerTensile Test Machine
CX-106
-
Shenzhen Chuangxin Instruments Co., Ltd.
The Tensile Testing Machine is widely applied to test the tensile, tear, peel, and bend of all kinds of materials, such as metal, cable and etc, it’s used to test the tensile, tear, peel, compressive strength and bending of the material. It conforms to the standard of GB, ISO7500/1, JJG475-88, ASTME4, DIN5122, JISB7721/B7733, EN1002-2, BS1610, and CNS9471/9470.
-
Product
Averaging Axial Extensometers for Large Compression Samples
Model 3542RA
-
Jinan Testing Equipment IE Corporation
Designed primarily for compressive strength tests on rock, concrete and other large compression samples, this model measures axial strain on opposite sides of the test specimen, and the output is an average of the two readings. Gauge lengths from 1 to 8 inches (25 to 200 mm) and measuring ranges from 0.050 to 0.250 inches (1.2 to 6 mm) are available.
-
Product
Automatic Upset Testing Machine
YQA Series
-
Jinan Testing Equipment IE Corporation
This kind of machine is designed according to the International standards EN 10263-1:2001 “Metallic materials upset test methods”, especially for the quality inspection of high-speed rods and wires. Through simulating the quick press conditions of the metallic materials during the upset and pressing, the machine truthfully reflects the instances of the quickly compressed rods and wires. This kind of machine is widely used in the steel industry, standard samples manufacturing industry, and tools manufacturing industry, for the inspection of the metallic materials upset tests. Under the room temperature or the hot conditions, exert test force on the direction of specimen axial line, quickly compress the specimen, and then inspect the metal ability of bearing upset deformation in the specified upset ratio. It also can show the metal surface disfigurements.
-
Product
SMA Connectors
-
Pasternack SMA connector category contains a large selection of part numbers, the majority are RoHS and REACH compliant. SMA connector products in this category will terminate to coax, PCB (printed circuit board) or terminal and are built to precise RF and microwave industry specifications. Our SMA connectors are constructed in male or female gender in standard polarity, reverse polarity (RPSMA / RP-SMA) or reverse thread threads, with 50 Ohm impedance. Connector SMA series from Pasternack are available in straight, radius right angle or right angle versions, as well as, press in, bulkhead, 2 hole panel, 4 hole panel or mountless options. These SMA designs include clamp/solder, compression, crimp/solder, crimp/solder (captive contact), field replaceable, solder, solder (without contact), solder/solder or solder/solder (captive contact) attachment methods. We offer connectors in SMA series with standard or high performance levels manufactured with brass or stainless steel bodies. Other SMA connector options include quick disconnect (QD) or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this SMA connector series is in-stock. But not just in stock, also they will ship the same-day as they are ordered.
-
Product
Amplifier Characterization With Wideband Modulated Signal
N5245BV
-
The N5245BV provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for amplifier measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements.
-
Product
Through Hole/ Donut Load Cell Compression only (1.50 O.D.)
THB SERIES
-
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
Leak & Seal Integrity Tester
-
Saicheng Leak Tester is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
Master Compression Tester
CT166AK
-
Tests compression on all domestic and foreign cars and light trucks with gasoline engines, including mini engines. High quality 2-1/2" gauge features a dual scale dial with ranges from 0-300 PSI and 0-21 bar.
-
Product
Pneumatic Horizontal Shock Response Spectrum Test System
KRD15 series
-
KRD15 series is the state-of-the-art shock response spectrum tester that adopts compressed gas energy to provide impact energy, push the shock hammer to impact the resonance plate, and generate high energy shock. Comparing to traditional pendulum shock response spectrum tester, this machine has the advantages of high energy, stable performance, high reliability, good repeatability, easy adjustment, safety and environmental protection. It is mainly applied in the industries of aerospace, aviation and ships.
-
Product
Keyboard Button Testers
-
Infinity Machine International Inc.
Keyboard Button Testers by Infinity Machine International Inc. - for applications such as keyboard button compression force tester, keyboard durability test machine, adjustable keystroke life-span tester, mechanical keyboard switch tester, computer keystroke tester, button force testing, key stroke force tester for load stroke curve test, rubber keystroke tester, and more.
-
Product
Hardness Tester
-
Jinan Testing Equipment IE Corporation
Hardness is the property of a material that enables it to resist plastic deformation, usually by permanent indentation. Indentation hardness measures the resistance of a sample to material deformation due to a constant compression load from a sharp object; they are primarily used in engineering and metallurgy fields. The tests work on the basic premise of measuring the critical dimensions of an indentation left by a specifically dimensioned and loaded indenter.
-
Product
Motorized Force Test System
MT Series
-
In the past, film extruders, paper producers, converters, and woven/non-woven fabric producers have had the choice of test stands and universal test machines which are either value-priced peak-force-only machines, or expensive computer-operated integral-load cell machines. Now you can have the best of both worlds in a single instrument. The series MT-1500, a simple to use computer operated tester, with Quality Control software for automatic calculation and graphical display of break, elongation, yield, modulus, and other, tension and compression force information.
-
Product
Portable Gas Calibrator
Model T750
-
Teledyne Advanced Pollution Instrumentation
The Model T750 is a portable, microprocessor based calibrator for precision gas analyzers. Using highly accurate mass flow controllers combined with compressed sources of standard gases, calibration standards are provided for multipoint span and zero calibrations. The T750 is housed in a high-density, molded travel case which includes an integral handle and wheels for durability and ease of use in the field.The Model T750 can be equipped with an optional UV ozone generator for accurate, dependable ozone calibrations, and production of NO2 when blended with NO gas in the included, internal gas phase titration (GPT) chamber. An optional photometer allows even more precise control of the ozone generator giving accurate and dependable ozone calibrations and enhanced GPT. A number of calibration sequences may be programmed into the non-volatile memory of the Model T750, covering time periods up to a year.
-
-
Product
PCI Express Receiver Board
AD12-2000-IRIGB
-
The AD12-2000-IRIGB is a high performance wideband 0.3-1.8GHz PCIe-bus receiver on a single PCIe Gen3 board, that can continuously digitize a wide portion of the RF spectrum, with a 3.6GSPS 12-bit A/D that can be synchronized with stability of better than +/- 100 picoseconds with respect to an IRIG-B 1PPS signal and global time codes from a satellite receiver or local site time reference. Designed for demanding military, scientific, industrial, communications, safety and electrical power utility applications, the AD12-2000-IRIGB has 60dB of gain adjust range (manual and AGC with programmable loop bandwidth), a wideband noise figure of 9dB, +11dBm 1dB compression point, and 2dB peak-to-peak ripple over the 300MHz to 1.6GB frequency spectrum.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
-
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
