Filter Results By:
Products
Applications
Manufacturers
Pneumatic
being of or for the use of pressurized gases.
-
product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
product
Optical Fiber Tensile Jig
This jig is designed for tensile testing optical fibers and other brittle fibers. The jig consists of upper and lower pneumatic flat grips with flat grip faces followed by large-diameter capstans.
-
product
Round Cold Trap
MCT12
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
product
Antenna Masts
Antenna Masts are an integral part of EMC and RF measurement systems. Innco system masts are renowned worldwide as the standard benchmark. Available in manual or automatic, using either pneumatic and or electric driven, the antenna mast design has the capacity to carry antennas of 6kg (MM) and 10kgs (MA) as standard. Higher loads are available upon request.
-
product
Lab Thermosol Range
TD640
TESTEX Testing Equipment Systems Ltd.
The fabric samples are padded by the horizontal pneumatic type padder is held on both ends by special clip bars, this complete sample holder is mounted on the chamins which are running endlessly through the machine.
-
product
RK Deadweight Tester
AMETEK Sensors, Test & Calibration
The RK floating ball type pneumatic dead weight tester is engineered to offer user-friendly, safe operation. The easy-to-use primary standard provides reliable and accurate pressure measurement in the field, or in a lab.
-
product
Portable Hydrostatic Hose Tester, 15000 psi; USMC
9901HT-8762
The 9901HT-8762 Hydraulic Hose Test System is utilized by the United States Marine Corp. for their portable forward base maintenance stations. The system includes it's own onboard "quiet" air compressor and a set of 37 degree flared test adapters from 3/16" through 2" as well as an onboard calibration gauge and pneumatic castors for use on rough terrain.
-
product
Motion And Position
Omega has all your motion control products in one place. We have motors, actuators, motor controls, pneumatic components, proximity sensors, rotary displacement encoders and more.
-
product
Aerospace Systems And Technologies
The world's leading aircraft manufacturers and engine makers rely on Parker Aerospace's flight control, hydraulic, fuel-inerting, fluid-conveyance, thermal-management, pneumatic, and lubrication systems and components. Parker's systems and technologies expertise helps move customers' programs forward while increasing productivity and profitability.
-
product
Soil Testing Complex
GEOMehanika-M
The developed measuring complex for testing soils with "GEOMECHANIKA-M" stamps includes:Control and registration unit: measuring station based on NI cRIO equipment, MIDA overpressure sensor, wireless access point AWK-3131-EU-T, pneumatic system based on pneumatics CamozziLinear motion sensorsWireless Operator Console TestSet of connecting cables
-
product
ServiceJunior Test-Kit
Parker's ServiceJunior diagnostic test kits are ideal to digitally measure pressure and capture min and max fluctuations in any hydraulic or pneumatic system.
-
product
Configurable and Scalable Connectors
iCon
Rugged engagement mechanism engineered for 10,000 cyclesRemovable backshell and engaging mechanism enable easy access to wiringPCB mountableStandard modules allow a mix of I/ORear-mounted modules allow for easy installation of pre-wired cable assembliesModules available in coax, power, signal, thermocouple, pneumatic and fiber optic, including hybrid combinations
-
product
Pneumatic Controllers
Campo Series
The Campo series of indicating controllers are suitable for field mounting and allow accurate measurement of pressure or temperature by associated primary measuring element; a dedicated model is available for generic 3 to 15 psi pneumatic input.These instruments provide high reliability with dynamic response, low maintenance, easily replaceable components, low air consumption, and improved compatibility with pneumatic valves.
-
product
Handheld Digital Manometer
475
The Dwyer Series 475 Mark III Handheld Digital Manometer is ideal for field calibration, monitoring or trouble shooting HVAC systems, clean rooms or a wide range of other low pressure pneumatic systems. This handy instrument measures positive, negative or differential pressures of air and natural gases in ranges from 1 in. w.c. (0.249 kPa) to 150 psid (10.34 bar).
-
product
Digital Pressure Gauges
SCJR1-KIT-EMA
Parker's ServiceJunior diagnostic test kits are ideal to digitally measure pressure and capture min and max fluctuations in any hydraulic or pneumatic system.
-
product
MCB Endurance Test Bench
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
-
product
ATE Test Probes
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
product
Signal/Mini Coax, Module, Receiver, TriPaddle, 90 Series, 16/16 Position
510104243
This module can accommodate certain VPC mini pneumatic contacts, but cannot be fully populated in all 16 positions with them. See specific product drawings for applicable limitations. For further assistance please contact a Field Application Engineer. Primary mating module 510108210.
-
product
Power Assembly Tools
In order to keep up with modern production demands, you need tools that are faster, smarter, more accurate, and more powerful than ever before. Mountz answers that demand from the heart of Silicon Valley with a full line of innovative electric and pneumatic power tools and automation systems. With intuitive Mountz tool controllers, complex multi-pass assemblies become simple and your production speed will skyrocket. Quality control and regulatory compliance can be streamlined with real-time error proofing and time stamped documentation. From the simplest repairs to the most technical manufacturing projects and everything in between, Mountz power tools stand out from the crowd.
-
product
Right Angle Poppet Valve
PV10
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
product
Hand Insertion Tools
Zierick Manufacturing Corporation
Ideal for low volume, short run and prototype PCB assembly applications, Zierick’s hand tools offer a simple and reliable method for inserting press fit and splay mounted terminals. The hand tool can be easily installed on any type of press machine for increased flexibility and faster insertion. With the addition of a lower tool die, terminals can then be splayed and locked into place to improve reliability and prevent part removal and rotation. Zierick hand tools are available for PCB-mounted quick-disconnect terminals, quick-disconnect receptacles, post receptacles, test points and IDC terminals. Simple and reliable method for inserting press-fit and splay mounted terminals. Single tool can handle multiple terminal insertion applications. Tools can be installed on almost any type of manual or pneumatic press. Please click here for a PDF user manual for Zierick's hand tools.
-
product
Tooling And Fixturing
Control develops and supplies fixtures and test accessories :*For a vast field of applications - ICT (In-Circuit Test), functional test, Flash programming, EoL (End-of-Line) test systems, etc.*For all handling systems currently used in the market: online or offline, mechanical, pneumatic or vacuum operation*From simple mechanical fixtures, with a few hundred probes and low production volumes, to highly complex accessories with thousands of probes, double-sided probes, double acting, etc.
-
product
Mini Pneumatic, Contact, ITA, Plug, Fits Mini Coax/ Mini Power modules
610132110
Mini Pneumatic, Contact, ITA, Plug, Fits Mini Coax/ Mini Power modules.
-
product
Hydraulic & Pneumatic Pressure Sensors
One of the toughest applications for pressure sensors is measuring high pressure, repetitive pulses, such as those encountered in hydraulic applications. However, our pressure sensors are designed to continuously measure repetitive pulses during applications such as hydraulic cylinder “torture” testing or diesel fuel injection. Ordinary diaphragm-type sensors usually fatigue quickly in such applications.
-
product
Electro Pneumatic Circuit
Unitech Scales And Measurements Pvt. Ltd
Electrical control of double acting cylinder by solenoidvalve.
-
product
EMC Actuator for Gas + Brake Pedal
PSE-GB
Pneumatically operated actuator for operation of accelerator and brake pedal in vehicles. External set-point of the pedal actuator position and brake pedal force via analog voltage to closed-loop pressure regulator in external valve box.
-
product
Torque Verification
90229
SDI’s 90229 is designed for calibrating tools used to apply torque including electric and pneumatic power tools, torque sensors, hand and click wrenches. The strain gage based reaction torque sensors in the bench-mount housing remain stationary while torque is applied. The housing dis-assembles by removing two snap pins, allowing the user to easily change socket sizes and capacities.
-
product
EZ-Slider Torque Arms
The EZ-Slider torque arm is crafted with a lightweight durable carbon fiber, the arm offers X & Y axis mobility. It provides the freedom to travel side-to-side and up & down on a production floor. An ideal ergonomic solution for multi-tool applications such as a moving production and assembly line where balancers are fixed to a trolley system. Eliminates torque reaction of assembly tools. Can be used with a variety of assembly tools like angle nutrunners and electric & pneumatic screwdrivers.
-
product
Steering Test Equipment: Software & Hardware
MB Dynamics delivers steering test equipment to help fulfill a myriad of application test requirements, or jobs-to-be-done. The steering test equipment consists of software for multi-test-head, synchronized MIMO closed-loop control and data acquisition; rotary servo motors for attachment to a steering spline or wheel; electrodynamic shaker systems; long-stroke linear motor actuators; pneumatic actuators; column stands for mounting steering column; gear fixture for mounting the gear; instrumentation (force, torque, displacement, rotary position, acoustic, acceleration); fixtures for mounting gears and columns; brackets, clamps, and fixtures for holding test items; jounce/rebound fixtures and tilt positioners for aligning input forces with tie rods at angles; software and associated data acquisition hardware up to 16 channels for recording, analysis and evaluation of in-lab steering noises and accelerations, road load data acquisition, and general Sound & Vibration analysis; and engineering services to accelerate test effectiveness.
