Filter Results By:
Products
Applications
Manufacturers
Scales
-
product
Shrinkage Template Scale
TESTEX Testing Equipment Systems Ltd.
Shrinkage Template Scale, suitable for all shrink testing standards. Shrinkage Template Scale complies with AATCC 135/150/160/179, BS EN 3759, ISO 3759, etc. Welcome to contact us if you have any problems about fabric shrinkage test method.
-
product
E-Type Thermocouple, 32°F to 900°F Temperature Sensor
745690-E002
E-Type Thermocouple, 32°F to 900°F Temperature Sensor - The E-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure measurements and predefined scaling coefficients for the E-Type Thermocouple and acquire synchronized temperature data in units of degrees. The E-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
product
PXI BRIC8 FIBO Matrix Dual 6x2 3pin brkout
40-595A-001
The 40-595A is a matrix module based on the BRIC format that is designed for fault insertion applications in safety critical testing. As with other BRIC modules the matrix size can be scaled to suit the user application. The 40-595 has a very high current rating of 10 Amps, ideal for higher power systems, and can be used as a conventional matrix.
-
product
Scaling Amplifier
SIM983
Stanford Research Systems, Inc.
The SIM983 Scaling Amplifier provides fine adjustable gain and offset control for analog signals. Both gain and offset are set with 3½ digits of resolution, and the signal path has more than 1 MHz of bandwidth.
-
product
Mass Flow Controller for Medium Flow
HFM-205 / HFC-207
The HFM-205/HFC-207, Teledyne Hastings' flexible, general purpose series of mass flow meters and controllers accurately measure and control mass flow in a variety of applications. Featuring reliability and stability, the 200 Series is chosen for its very stable performance with varying ambient conditions. A wide choice of elastomer seals make this flow controller compatible with most gases.The HFM-205 / HFC-207 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured with normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a full complement of fitting and elastomer options, the HFM-205/ HFC-207 covers a wide range of high flow applications.
-
product
Weighing Instruments
ZhangZhou Weihua Electronic co.,ltd
are devices to measure weight or calculate mass. Spring balances or spring scales measure force (weight) by balancing the weight due to gravity against the force on a spring, whereas a balance or pair of scales using a balance beam compares masses by balancing the weight due to the mass of an object against the weight of a known mass or masses. Either type can be calibrated to read in units of force (weight) such as newtons, or in units of mass such as kilograms, but the balance or pair of scales using a traditional balance beam to compare masses will read correctly for mass even if moved to a place with a different (non-zero) gravitational field strength (but would then not read correctly if calibrated in units of force), while the spring balance would read correctly in force in a different gravitational field strength (but would not read correctly if calibrated in units of mass).
-
product
High Speed-Large Current DC Electronic Load (CC/CV/CR/CP)
PLZ-4WL Series
While the PLZ-4WL series succeeds to the superior operability of our conventional model of the PLZ-4W series, the PLZ-4WL series realizes the high speed rise and fall time (slew rate of 50A/µs.) in the range of low voltage with large current. The PLZ-4WL offers six operation modes, and equips with various features such as sequence operation, switching operation, soft-start function, and time and voltage measurement. The PLZ-4WL applies not only for the conventional load test of the CPU power supply, but also it can be applied to even faster current response test. In addition, the PLZ-4WL is a space-saving design (about 50% less volume of the conventional model) that can save the facility space of the testing site, and it can be applied for the single cell testing of the large scale rechargeable battery.
-
product
Mini Low Profile Load Cell Universal/ Tension or Compression
MLP SERIES
The model MLP Series load cells were designed with economy as first priority. They are a scaled down version of our successful LPO Series Load Cells. MLP-10 through MLP-300 are anodized aluminum and the MLP-500 through MLP-1K are made from 17-4ph heat treated stainless steel. The unique low profile design of the MLP Series provides excellent stability for in line applications for tension and/or compression, while saving space at the same time.
-
product
SINE M-6 Sinusoidal Array
The Sinusoidal Array SINE M-6 contains the same gray scales and sinusoidal areas as the M-5 but is arranged in a shorter and wider format, making it particularly useful when the complete array is to be imaged at one time.The overall size of the array is 70mm x 46mm; centered on an 8.5 inch (215mm) strip of 70mm film, which can also be mounted in glass (TM-G variations) at each modulation (-35, -60, -80).
-
product
Magnetizer
340B
The Model 300-series magnetizers are designed to handle a variety of magnetizing applications and materials, from small Alnico parts to large blocks of neodymium-iron. Each of these magnetizers feature patented ECS (Electronic Capacitance Switching) technology, which allows the user to change the capacitance of the unit through the front panel. By setting the charging voltage and capacitance of the magnetizer properly, the user can then scale the output energy of the unit to match the magnetizing fixture being used. The 300-series magnetizers also includes a peak current meter, which automatically captures the peak current of the magnetizing pulse once it occurs. A safety circuit internally discharges the capacitor banks if mains power is removed from the magnetizer or if the cabinet is opened during operation. When connected to a suitable magnetizing fixture, the magnetizer is able to disable its front panel controls if the fixture overheats. Other features include a lockout keyswitch and a current sense output jack (this connects to an oscilliscope for viewing of the magnetizing pulse). All 300-series magnetizers can be modified for computer control, photocell trigger, or autocharge operation.
-
product
Single-Tenant Colocation Cabinets
SmartCabs
Benefit from the scale and speed of the cloud while still retaining the control, performance, and security of a dedicated infrastructure. SmartCabs are single-tenant colocation cabinets that come complete with built-in power and network connectivity as well as access to the Digital Exchange, our configurable core network fabric.
-
product
Switchboard Instrument Voltmeter
ST-96
Standard Electric Works Co., Ltd
● Test Voltage : 2kV 50-60Hz● AC Ampere Over Load Scale：200%, 300%, 500%● Composition：Glass Window, ABS resin frame and case, Bakelite base● Color：Black case and frame, white scale plate and meter body● Pointer：Stick shape in black color● Pointer Length：55mm.
-
product
Dynamic Analysis
DAST
Dynamic application security testing at the scale and speed modern enterprises need. WhiteHat™ Dynamic rapidly and accurately finds vulnerabilities in websites and applications, with the scale and agility you need to identify security risks across your entire application portfolio.
-
product
P Series Panel Meters
ST-38
Standard Electric Works Co., Ltd
● DC up to 15A● Case and Composition: Acrylic resin front. ABS case. Four studs mounting. Two studs mounting.● Accuracy :DC : Class 2.0 AC : Class 2.5 Rectifier : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Structured Light
Structured light systems from ams enable 3D imaging applications to achieve extremely high accuracy. Accurate structured light technology is behind the user face recognition being implemented in smartphones. Structured light products and design expertise from ams help customers get to market quickly and scale up production rapidly.
-
product
Supporting Micro Flowrate Range Liquid Chromatography Mass Spectrometry System
Nexera Mikros
Improvement in the sensitivity of an LC/MS/MS method can generally be achieved by reducing the analytical scale of the analysis. However, reducing the analytical scale significantly to nano-flow reduces the throughput, stability, and robustness as a trade-off for greater sensitivity. Nexera Mikros, a Shimadzu microflow LC/MS system, offers a balanced solution to increased sensitivity with less compromise to throughput and robustness, using flow rates from 1 to 500 μL/min and column I.D. from 0.1 to 1 mm. It achieves stable and sensitive quantitative analysis through robust performance of microflow solvent delivery, optimized ion source design, the unique UF-Link column connection, and system variety that supports a wide range of applications.
-
product
Wattchman RF Station Monitor/Alarm Systems
81080 Series
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
product
Portable Power Factor Meter
ST-2000 Cos∮
Standard Electric Works Co., Ltd
● Principle : Phase angle sensing transducer● Rated Accuracy : ±3% phase angle● Scale : Power Factor：Lead 0 – 0.3 – 1.0 – 0.3 – 0 Lag Power Angle： Lead 90° – 0° – 90° Lag● Effective Power Factor Measuring Range : Lead 0.5 – 1.0 – 0.5 Lag● Scale Length : Approx. 135mm(5-3/8”)● Frequency Influence : Within ±1.5° phase angle at 45 to 65Hz
-
product
Portable Hardness Tester
Handheld Hardness Testers
Handheld Hardness Testers are ideal hardness testing tools where large samples, which cannot be brought to a traditional tabletop hardness tester, or specimens with hard to access areas are to be tested. A wide variety of the portable hardness testers, offered by Qualitest ensure that we recommend the most suitable model for your application. The extensive selection of our handheld hardness testers is available from low-cost economy models up to advanced models coming with more features. These models can measure the hardness of your materials in Rockwell, Superficial Rockwell, Brinell, Vickers, Webster, Barcol scales and often conversions can be done.
-
product
OEM Solutions
About 80 percent of piezosystem jena’s business is in supplying industry customers with positioning solutions on a large scale. Almost all these solutions are highly customized or even developed and build from the scratch.
-
product
M Series Panel Meters
ST-66
Standard Electric Works Co., Ltd
● M Series all up to 15A● Case and Composition：Acrylic resin front and ABS resin case. Four studs mounting.● Accuracy：Moving coil type : Class 2.0 Rectifier type : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
product
Programmable Setpoint Relay Protection Relay, Trip Relay
CRD-005 and CRD-020
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbullet CRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbullet CRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbullet CRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbullet Lid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bullet Red LED lamp lights to indicate when the threshold level has been tripped
-
product
Analogue (1kV below) Insulation Tester
2132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
RMS Responding Power Detectors
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
product
Microscope
Instrument that produces enlarged images of small objects, allowing the observer an exceedingly close view of minute structures at a scale convenient for examination and analysis.
-
product
High Line Pressure Transducer
P365
The P365D transducer is designed to make low differential pressure measurements at high static line pressures. Operating from unregulated 9 to 55Vdc, the P365D is available with 4-20mA, 5Vdc or isolated 5Vdc output over full scale pressure ranges from 8 to 10,000 psid. The output shift due to static pressure will not exceed 3% of full scale, up to a line pressure of 10,000 psig.
-
product
Photometer II
Spectra Film Gate
The Spectra Film Gate Photometer II offered by Spectra Cine is a significant advance in the field of photometry. It is extremely sensitive and solid state throughout. Reads directly in printer steps of 0.025 log exposure units. The large, uncrowded scale has an 80 printer point range and affords ease and accuracy in reading. A variety of probes are available for use in Acme optical printers, Bell & Howell Model "C", "J", and "A" contact printers, ARRI printers and Oxberry printers.
-
product
Pit-type Truck Scale
KMT Series
These scales accommodate various requirements such as easy measuring and multiple application of measurement data. They provide a user-friendly measuring system for a variety of data-processing systems.
-
product
Portable Single Phase Power Factor Meter
Supreme Instrument Laboratories
Portable Electro-dynamometer type single phase single element Power Factor Meter laboratory type for horizontal use, housed in laminated wooden cabinet size 235 mm length x 200 mm width x 180 mm height, with detachable lid, black bakelite panel fitted with anti-parallax mirror scale, knife edge pointer, rubber footings, carrying handles, locking arrangements. The power Factor Meters are fitted with an iron shielded Electro-dynamometer type cross coil system.
