PCB Inspection
The check and evaulation of Printed Circuit Boards.
See Also: Visual Inspection, Bed of Nails, Flying Probes, AOI, Burn-In, Automated Optical Inspection
-
Product
GPR System for Concrete Inspection
StructureScan Mini XT
-
Geophysical Survey Systems, Inc.
The StructureScan Mini XT is GSSI’s newest generation of our very popular all-in-one GPR systems. The StructureScan Mini XT offers a 2.7 GHz antenna for superior target resolution and can reach depths of 20 inches (50 cm). Ideal for locating rebar, conduits, post-tension cables, voids, and real time determination of concrete slab thickness.
-
Product
Wafer Sorter and Inspection
SolarWIS Platform
-
Eliminating the opportunity for problematic wafers to enter cell manufacturing lines greatly improves output and yield. ASM AE’s wafer sorter features 3D area inspection capability to inspect wafer thickness, total thickness variation (TTV), saw marks, as well as wafer bow and warpage. SolarWIS also includes modules that can inspect for stain, geometry, micro-cracks, edge chips, resistivity, P or N conductivity and lifetime.
-
Product
Wafer Inspection Products
-
Sonix provides manual and automated wafer inspection and metrology systems for wafers ranging from 100mm to 300mm, with extensive analysis capabilities at both the wafer and device level. These industry-leading automated wafer inspection systems are used by the world’s top manufacturers to ensure quality from development through production.
-
Product
Thickness and Flaw Inspection
FOCUS PX / PC / SDK
-
Olympus offers a complete advanced phased array integration solution that meets the requirements of your most demanding customers. The solution includes the FOCUS PX, a powerful and scalable acquisition unit; FocusPC, a powerful data acquisition and analysis software program; and three software development kits (SDK), FocusControl, FocusData, and OpenView SDK, to customize your software interface based on your application and control FocusPC for a fully automated inspection solution.
-
Product
Micro Power, Contact, Receiver, 21 Amp, PCB Mount
610142102
-
Primary mating contact 610143101. (May mate with other ITA contacts, as well.)
-
Product
Can Inspection
-
Whether they are 14oz cans, 28oz cans, 12oz bottles, or some other size or format – they typically all look fine, as they fly by on your production line or sit on pallets ready to go out to customers. The challenge is, most companies have some kind of sealing issue at some point. Tops go on crooked, lids don’t seal, vacuums don’t set right – and it’s nearly impossible to tell by physical or visual inspection.
-
Product
Automated Optical Inspection System
AV880 Series
-
The AV880 Series of AOI solutions from ASC International provides the same high level inspection capabilities as found in our AV862/AV871 Series of AOI systems all wrapped into an inline platform for continuous flow requirements. A price to performance ratio sure to please those looking for a quick ROI.
-
-
Product
68-Pin SCSI Micro-D Fem. Right Angle PCB
40-963-068-RF
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Signal & Power PCB Connector
HPW Series
-
Smiths Interconnect's HPW series is a versatile interconnect with mixed signal and power contacts, up to 15A each
-
Product
Laser Sherography NDT Sensor for Post-Production Quality Control or In-Field Component Inspections
FlawExplorer
-
The FlawExplorer is a laser shearography NDT sensor designed to be used for post-production quality control applications or in-field (in-service) component inspections. Depending on the application, the sensor can be configured with thermal or vacuum (partial) excitation systems and may also be automated. It incorporates the very latest in phase-shifting technology delivering accurate and reliable measurement results through clear and sharp imaging with sub-micrometer displacement resolution.
-
Product
X5 Pipeline X-Ray Inspection
-
Designed to be integrated into the production line and available with product pipes in 2.5 and 3 ", the X5 pipeline is perfect for a wide range of pumped products such as poultry, meat, slurries and sauces. The system is capable of offering good detection levels on a wide range of contaminants including all metal, bone, glass, dense plastics.
-
Product
Inspection Systems
-
Video Inspection Systems with?or without measurement capabilities are an excellent way to evaluate and test small items or items in?difficult to access locations. Many options are available in addition to the measurement capability. Video Inspection is used for a variety of purposes including the ability to see? and measure items that are much smaller than the eye can see or that hand tools can measure. Video systems can also reduce the eye and/or back strain associated with production environments where an operator must look in a microscope all day.
-
Product
PC Based Test Setup for LED PCB of Luminaire
-
The panel carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 40 seconds.
-
Product
Building Inspection System with Moisture Hygrometer & MSX® IR Camera
FLIR MR277
-
The MR277 is the first FLIR building inspection system to combine the advantages of Infrared Guided Measurement (IGM) and our patented Multi-Spectral Dynamic Imaging (MSX) with advanced environmental sensors to help you quickly locate, clearly identify, and easily document problems. IGM technology and a laser pointer isolate the area where you can use the integrated pinless moisture sensor for non-invasive readings or external pin probe for invasive measurements. With automatically calculated environmental readings and a field-replaceable humidity/temperature sensor, the MR277 lets you finish the job and minimize downtime. Connect to external devices with METERLiNK® and use FLIR Tools® to enhance troubleshooting and reports.
-
Product
3-Pin Power D-Type Connector, 40A, Male PCB Mount
40-963-003-RM
-
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB
-
Product
Thick Film Inspection
785
-
For thicker coatings such as coal tars, extruded and tape coatings, the Model 785 has a range of infinite voltage settings from 1,000 to 15,000 volts.
-
Product
Mini Coax, Contact, Receiver, Right Angle for PCB Mounting
610104160
-
For use with VPC Module 510104319.Primary mating contact 610103136. (May mate with other ITA contacts, as well.)
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
Hold-Up Power Module - PCB Only Without Cover
055-149
-
Hold-Up Power Module for voltage input of 16 to 36VDC provides maximum power output of 330W for 50ms per MIL-STD 704 / DO160. Board can be ordered as fixed-mount or plug-in version.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 155gf
K100-H080155-SKAU
-
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
-
Product
Field Inspections
-
MISTRAS Group has evolved into an asset protection industry leader on the backbone of our expansive non-destructive testing (NDT) and field-testing portfolio.
-
Product
160-Pin DIN41612 Connector, Right Angle PCB Mount, Female
40-963-160-RF
-
Accessory allows a user to create their own PCB based termination solution. Female versions are suited to direct connection to a Pickering Switching Module while male versions can be used to interface to a female cable assembly termination.
-
Product
Compact Inspection Camera
-
Fits in your pocket or clips on your beltAffordable1 meter drop-proofLong, thin camera-tipped probe with excellent depth of field penetrates tight, hard-to-reach spacesProbe is waterproof, holds its configured shape, and coils inside clamshell case for storageFour camera-lighting LEDs produce bright, crisp video on large color LCDFour screen controlsFour useful probe tip accessories (pickup hook, magnetic pickup, 45 mirror, thread protector)
-
Product
Abrasive & Blast Inspection
-
Blasting parameters: A number of important parameters need to be monitored during the blasting or water jetting process, these include: air pressure (at the nozzle), nozzle diameter, blast media contamination & pH values in order to avoid recontamination of the substrate during blasting.
-
Product
Flying Probe PCB Test and Repair System
GRS500
-
Designed to help troubleshoot complex boards when fixture based tools are not a viable solution, the GRS500 is designed to help you compare the characteristics of good and faulty PCBs, using nodal impedance test, and a "Videosection" technique which presents you with high resolution images of a good board for use in live video comparison with the board under test,
-
Product
Tracing-Type Non-Contact Inspection System For LCD/STN/Touch Panel/FPC
TTS
-
*"Probe + Non-Contact Sensor" enables to delect SHORT after sticking LCD*No Fixture in LCD Inspection*Applicable to FPC Inspection
-
Product
Optical Inspection Machine
3D AOI
-
3D AOI latest optical inspection machine 1. No part dead angle, 4-way projection, complete measurement 2. Part height measurement, accurate measurement of defects 3. Multi-piece inspection without additional program 4. DLP digital projection, program editable height measurement
-
Product
9-Pin D-Type, Male, Straight PCB Mount
40-963-009-SM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
