Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
product
PXI Single Microwave SPDT Relay 18GHz 50 SMA - External Termination
40-781-121
This single microwave SPDT relay module is part of the 40-781 range that consists of one or two changeover switches capable of switching frequencies to 18GHz in 50 Ohm. Versions are available with either internal or external terminations and connections are made via front panel mounted high quality SMA RF coaxial connectors.
-
product
High-Frequency Ultrasonic Imaging System
USPC 3060 UHF
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The ultrasonic imaging system USPC 3060 UHF is optimized for the testing wih high frequencies and delivers high resolution B-, C-, Dand F- scans. It consists of a scanning system with water tank and the external pulser-/receiver module as well as a 19”-rack with scanner controller and the ultrasonic system and monitor, keyboard and mouse.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
Tracker for Testing CPV Module Systems
The tracking precision of our biaxial tracker is better than ±1° on each axis, with an option for ±0.1° precision. This makes the tracker ideal for testing concentrating PV modules. The software runs all required tests for angle-dependent testing of PV modules according to IEC 62108.
-
product
LXI High Density 256x16 2A Matrix
60-554-008
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
Satellite & Payload Check-Out Systems
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
product
75 Ohm Mini SMB to 1.0/2.3 Adaptor Assembly
40-978-731-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 225x4, 3 Sub-cards
40-568A-103
The 40-568A-103 is a PXI 1-pole 225x4 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-568A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI 4 Slot BRIC 92x8 1-Pole Dual Analog Bus (2 sub-cards)
40-560A-021-92X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
product
IAC Test Light
3501
Peaceful Thriving Enterprise Co Ltd
For GM1982 and newer GM TBI and PFI fuel infection system with square 4-pin connector. For GM vehicles with throttle body or port fuel injection systems, check the electronic control module signal that provides direction to the idle air control motor.
-
product
PXI 2A Multiplexer, 2-Bank, 4-Channel, 16-Pole
40-614C-014
This 2-bank, 4-channel, 16 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
75 Ohm BNC to MCX Adaptor Assembly
40-978-781-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXI/PXIe RF Matrix, 16x4, 100 MHz, 75 Ω SMB With Loop-thru
40-727A-101-L
The 40-727A-101-L (PXI) and 42-727A-101-L (PXIe) are 16x4 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
product
PXI High-Density Matrix Module, 16x8, 1-Pole, 2 A 60 W
40-529B-001
The 40-529B-001 is a 128 crosspoint PXI matrix with single pole switching. The matrix is configured as 16x8 using electro-mechanical relays with 2 A current handling.
-
product
VME Load Card
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
product
64 Channel 12bit 62.5 MS/s Digitizer
VX1740D
The VX1740D is a 1-unit wide VME64X 6U module housing a 64 Channel 12 bit 62.5 MS/s (65 MS/s using external clock) Flash ADC Waveform Digitizer and featuring 2 Vpp single ended input dynamics on two ERNI SMC connectors.
-
product
PXI/PXIe High Density Electro-mechanical Relay Module, 75xSPST, Normally Open
40-145A-101
The 40-145A-101 (PXI) and 42-145A-101 (PXIe) 75xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
product
SIMRC - 8 x Reed Relay Module, SPST
1010-R-8-1-5/1D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
PXI Single Microwave SPDT Relay 18GHz 50 SMA
40-780A-521
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PXI/PXIe MEMS RF Multiplexer, Quad 4-Channel, 4GHz, 50Ω, SMB
40-878-241
The module is based on the latest micro-electromechanical system (MEMS) switching technology and has low insertion loss and VSWR. In addition, MEMS devices have a long operational life of >3 billion operations and benefit from an operating time of <20 μs allowing greater test system throughput. The multiplexers have excellent and repeatable RF characteristics beyond 4 GHz with each path having a nominally equal insertion loss.
-
product
PXI 4-Slot BRIC Matrix, 10x32 1-Pole (2 Sub-cards)
40-562B-021-10X32
The 40-562B-021-10X32 is a high density BRIC4 matrix module with a size of 10x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 24xSPST High Voltage Power Relay Module
40-330-001
The Pickering Interfaces 40-330 High Voltage Power Relay Module is suitable for applications requiring high voltage power relay switching with high density.It features current handling up to 5A, 1000VDC/1000VAC peak cold switching and 110VDC/250VAC hot switching. It is configured as a bank of 12, 18 or 24 separate Single Pole Single Throw (SPST) relays. Connections are made via a front panel mounted 50-pin (24xSPST) or 37-pin (18 and 12xSPST) high voltage D-Type connector.
-
product
COM Express Type 2
Axiomtek COM Express Type 2 modules are designed with all components necessary and offer the most updated bus interfaces. The COM Express modules satisfy a wide range of vertical embedded applications with features of great computing performance and rich I/O capabilities, and reduce customers' time-to-market and ownership cost.
-
product
48 Channel Relay Output Module
DP-VME-4059
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
product
Signal, Module, Receiver, CASS, 210 Position, Discrete Wiring
510113125
Module, Receiver, Cass, Signal, 210 Position, Discrete Wiring
-
product
4-slot Fanless Industrial System With 4th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor (up To 3.3 GHz), Intel® Q87 Chipset, And Front-access I/O And PCIe/PCI Slots
IPC934-230-FL
To provide excellent computing capability, the high performance IPC934-230-FL industrial PC is equipped with the newest 4th generation Intel® Core™ i7/i5/i3 or Celeron® processor in 22nm process and Intel® Q87 Express chipset. Total four PCI/PCIe expansion slots allow installation of a variety of off-the-shelf PCI/PCIe cards for configurable applications. The rugged Intel® Hasewell fanless industrial computer is an ideal fit for automatic optical inspection, digital signage appliance, POS/kiosk, embedded controller, factory automation and many more applications.The 4-slot industrial PC is guaranteed to operate reliable in temperature ranging from -10°C to +50°C and is equipped with a 10~30 VDC 150W wide range power supply for mission-critical environments. It supports an easy-to-install fan module to dissipate heat generated within the system when high power consumption PCI/PCIe cards are installed. The all-in-one industrial embedded computer provides rich I/O connectors include two 2.5” SATA HDD, one CFast™ socket, four COM ports (one RS-232/422/485, three RS-232), two USB 3.0 ports, four USB 2.0 ports, dual Gigabit Ethernet, PS/2 ports, one DIO, audio and DVI-I. Moreover, the IPC934-230-FL supports various power protection including OVP (Over voltage protection), OTP (over temperature protection), OPP (over power protection) and SCP (over circuit protection) for more system safety.
-
product
LXI High Voltage Switching - 2-Bank, 1-Pole, 24:1 Multiplexer Plugin Module
65-231-903
The 65-231-903 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
PXI 8-Slot BRIC 168x8 Matrix, 2A 2-Pole (7 sub cards)
40-565A-102-168X8
The 40-565A PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps at 150VDC/100VAC The 40-565A BRIC modules are available in 2, 4 or 8 slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI MUX 1 Bank, 64 Channel Screened 1 Pole
40-610-021-S-1/64/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
