Can bus
Controller Area Network
See Also: Serial, I2C, LIN, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57621
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUCs (digital upconverters)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- 2 GB of DDR3 SDRAM; 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
USB ASSP
µPD720201
-
The µPD720201 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides four USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
-
Product
RTSI Bus Cables for 2 PCI or AT/ISA Devices
776249-02
-
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
Bus Analyzer
FireSpy® 9432bT/9832bT
-
The FireSpy9432bT and FireSpy9832bT bus analyzer is world’s only 9-bus IEEE-1394 protocol analyzer. Based on the 4th generation FireSpy analyzer architecture the FireSpy9432bT/9832bT are the most advanced 1394 test equipment in the market. The FireSpy9432bT/9832bT in fact combine nine FireSpy analyzers in one single instrument. They comprise a significantly more powerful on-board processor and improved connectivity to the host.
-
Product
Boards
MIL-STD-1760
-
The MIL-STD-1760 interface card is compatible with all common variations of MIL-STD-1760 and provides a wide range of features normally found only on full size testers. The cards can operate simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports Checksum, SRQ bit and Header Words as well as error injection and error detection.
-
Product
PCI/DSP Module
PCI-4pack-2
-
The PCI-4pack module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the PCI-4pack is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc.Custom application software can be downloaded to the DSP via the PCI bus. Windows 95 and WinNT drivers are standard.
-
Product
3U VPX Single Board Computer
VP32002
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP32002 is a high-performance 3U VPX single-board computer, compatible with PC architecture, especially it is a China Local-design, Local-assembling product. VP32002 is an all-in-one design, supporting the 3rd generation of Intel core processors and QM77 chipset; also supports up to 16 GB onboard DDR3 memory and up to 32GB Disk-On-Modules, these features ensure its stable operation in strong shock and vibration environments. VP32002 supports a XMC interface and various I/O interface such as two SATA600 channels, two Base-BX/T GbE, two UARTs and two USB interface.The board provides a flexible PCI-Express bus interface to the backplane. The interface can be configured as follows: 1 Port x8 PCIe, 2 Ports x4 PCIe, 4 Ports x2 PCIe. This feature makes it suitable for either distributed switching system or centralized switching system.For the user to quickly form application solutions, LinkedHope provide VP32002 a complete driver package including Windows, VxWorks, Linux and QNX.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope
780319-03
-
1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
CPCI Advanced Compute And IO Board
-
Advanced Compute & IO Board is high end Microprocessor based Mixed Input & output Board. It is suitable for high speed Data Acquisition, Simulation, ATE applications. This board have digital I/O signals, analog I/O signals, USB, RS232, Ethernet interface and external bus interface. Board is well suitable for special type data acquisition & processing application. Board has high end FPGA which is used for automatic (Programmable) data acquisition and very useful high speed data acquisition. Board is based on CPCI architecture and can be used with CPCI or PXI backplane.
-
Product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
-
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Product
2-Channel 500 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
16U (28") Non-Insulated Bus Bar
BB-28
-
16U (28") non-insulated bus bar provides cabinets with recessed rail option and a convenient, isolated common grounding mechanism.
-
Product
8th Gen. Intel® Core I7/i5/i3/Celeron 3.5" SBC W/ MIOe
MIO-5373
-
8th Gen. Intel Core Processor with Quad/Dual Cores, TDP 15WDual Channel DDR4-2400 up to 32GB, onboard eMMC up to 64GBTriple simultaneous displays by 48-bit LVDS/eDP+HDMI+DP2 GbE, 4 USB3.1, CAN Bus, M.2 M-Key 2280 supports NVMe, DC-in 12-24VSupports iManager, SUSI APIs, WISE-DeviceOn and Edge AI Suite
-
Product
PCIe-8239, 4-Port, GigE Vision Frame Grabber Device
787790-01
-
The PCIe-8239 features Power-over-Ethernet (PoE) technology. It provides optimized performance of high-resolution and high-frame rate cameras through the combination of independent Gigabit Ethernet ports and the high-performance GigE Vision driver software. PoE reduces the need for additional external power supplies by powering cameras over the Ethernet bus, which simplifies system design and cabling complexity.
-
Product
PCIe Module
PCIe-1553-uAce-1,2
-
1or 2 controllers of dual redundant (A/B channel) 1553 communications• Programmable bus controller, remote terminal, or monitor terminal modes• MIL-STD-1553 A and B compliant, Notice 2 RT• STANAG 3838 bus compliant for NATO standard support• Long or short stub support • Low power consumption• PCIMG compliant• Single +5 VDC supply
-
Product
6 GHz Programmable Delay Line
PADL6
-
The PADL6 is a programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz. Delays are controlled via a TTL level bus.
-
Product
PXI BRIC8 2Resource Distributor, 3Bus Matrix
40-569-123
-
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
MIL-STD-1553 Test & Simulation Interface for VME
VME-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
USB Protocol Analyzers
Beagle Series
-
Our line of Beagle Protocol Analyzers provide real-time visibility into I2C, SPI, and USB systems making them ideal tools for embedded engineers.The Beagle analyzers provide high-performance bus monitoring in a small, portable package that includes cross-platform software support making it perfect for engineers in the field and in the lab.
-
Product
Bus Analyzer / Exerciser
VME850
-
The VME850 Analyzer / Exerciser supports the latest VME bus specifications and protocols. From standard VME transfers to 2eSST protocol. In addition to the VME bus, user defined signals on the P0 and P2 connectors are also analyzed and exercised with optional plug-in modules.
-
Product
PXI 8-Slot BRIC Matrix, 230x8, 1-Pole (5 sub-cards) Dual Bus
40-560B-121-230X8-M
-
The 40-560B-121-230x8-M is an ultra high density matrix module with dual analog buses and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays
-
Product
4-Channel 200 MHz A/D with DDC with Virtex-6 FPGA - 3U VPX
Model 52661
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
-
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
Product
Portable Bus Analyzer
1553
-
Our new inline Bus Monitor is a very small, very light MIL-STD 1553 Bus Monitor that can be connected to any Windows device with a USB connector. It monitors and records all or selected 1553 traffic for later analysis or reconstruction in the lab.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
-
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
MIPI SLIMbus
-
A typical mobile device has many low-speed/bandwidth peripherals connected to the host processor, which include microphones, speakers, sensors and many others. There is a need for a standard bus that enables multiple audio channels, peer-peer communications and lower pin count on the host processor. The MIPI alliance has defined the SLIMbus specification which provides a standard, robust, scalable, low-power, high-speed, cost-effective, two wire multipurpose interface that supports a wide range of digital audio and control solutions for mobile terminals.
-
Product
Eurocard Plugbord
4616, 160-PIN VME64x
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 160-pin DIN connectors. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads (0.28” x 0.080”) for interconnecting multiple component leads.Interleaved buses on both sides, back-to-back. Pad and bus surfaces solder-coated for user convenience. Row and column legends provided.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 3UVPX
Model 54821
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range/analog signal integrity- Xilinx® Kintex® UltraScale" FPGA- Compatible with several VITA standards including: VITA 66.5, VITA 67.2 and VITA 67.3C- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of 2400 DDR4 SDRAM- Programmable frequency synthesizedsample clock generator- Sample clock synchronization to an external system reference- Powerful DMA controllers for moving data- PCI Express (Gen. 1, 2 & 3) interface up to x8- Multi-channel synchronization with clock/sync bus- Optional clock/sync generator for multi-board systems- Optional gigabit serial links for custom FPGA I/O- Optional LVDS port and gigabit serial links for custom FPGA I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
3U CPCI To PCI 4 Slot Adapter
-
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
Product
4-Channel 200 MHz A/D with DDC, VITA 49.0, Virtex-6 FPGA - XMC
Model 71664
-
- Complete radar and software radio interface solution- PCIe output supports VITA 49.0 VITA Radio Transport (VRT) Standard- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
