-
product
LED Driver Automatic Test System
ATE-2
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
product
Image Sensor Test System
IP750
Teradyne's IP750 series dominates the image sensor tester market with its superior performance and low cost of test. The IP750 delivers high throughput and high parallel test efficiency, broad device test coverage from CCD and CIS, analog and digital capture, and concurrent image sensor and logic testing. In addition, Teradyne's IG-XL software environment provides easy, shorter test program development and easy maintenance.
-
product
VFTLP+ Test System
4012
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
product
Portable Test System
MT781
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
product
Laser/LED Devices
Whether you manufacture or sell CD and DVD drives, laser pointers, or Blu Ray discs - you are probably more than aware of the potential hazards of high-powered, bundled radiation in laser products. As an independent testing institute, TÜV Rheinland can check your products for full compliance. We can classify and certify your products in accordance with international standards and the prescribed DIN EN 60825 norm.
-
product
MEMS Test System Development
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
-
product
IPTV Set-Of-Box Auto Test System
Guangzhou Jumho Electric Co., Ltd.
IPTV Set-of-Box test system is general audio/video test system for IPTV RCA signal output. This system has these features: Based on high-speed, high resolution data acquisition board from National Instruments. It can support all video and audio parameters testing.High speed, 3x than traditional video analyzer and audio analyzer.
-
product
Test DVD For OmniMic Precision Measurement Systems
OMDVD Version 1
The Dayton Audio OMDVD Test DVD brings the ease of the OmniMic V2 system to measurements of 5.1-channel audio systems. It’s the essential tool for professional installers and home theater enthusiasts to ensure proper audio calibration and optimization of a home theater or multichannel music system for the highest possible performance. The full functionality of the OmniMic V2 measurement system is now available through every channel of a 5.1-channel audio system thanks to the OMDVD Test DVD’s suite of high-quality test tones, and an intuitive menu structure that has been optimized for ease of use.
-
product
Bus Management Test System
Solution to test redundant Architecture of BMUComprehensive test system performing tests of > 3000 I/O's Special test circuits using hybrid / ceramic components to operate in Thermovac chamber Tests various subsystem functionalities like, AOCS, Sensor Electronics, Telemetry, Tele-command with Self test and application test software
-
product
Clock Generation Devices
Analog Devices offers ultralow jitter clock generation products for wireless infrastructure, instrumentation, broadband, automatic test equipment, and other applications demanding subpicosecond performance. Our clock products are ideal for generating the high speed, low noise clock signals required to clock high performance analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). ADI clock ICs integrate PLL cores, dividers, phase offset, skew adjust, and clock drivers in small chip scale packages.
-
product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
product
Compression, Paper And Pulp Test Systems
From basic tension and compression testing to advanced materials testing
-
product
Power Supply Test Systems
FineSoft on LabWindows CVI platform 2 testers connected with Ethernet hub to dedicated server GPIB Test.
-
product
Test System for Circuit Breakers
Spitzenberger & Spies GmbH & Co. KG
Thermal testing with long-time currents up to 550 A. Magnetic testing with short-time currents up to 2000 A. Control software. Customer specifically adapted. 4 candidate records with pneumatic adapting.
-
product
Photoelectrochemical Test System
SolarLab XM
SolarLab XM is an application specific XM (Xtreme Measurement) product that is primarily focused on solar cell / photovoltaic research, developed in conjunction with Professor Laurie Peter of the University of Bath, UK.
-
product
Primary Injection Test Systems
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
product
Tracer Gas Leak Test Systems
Tracer gas leak testing is a simple and highly-efficient method of leak detection that provides high sensitivity as well as increased accuracy and repeatability. This method is used for testing parts with very low leak rates that are outside the range for conventional air-flow pressure decay and mass flow, or to replace bubble test methods. Tracer gas testing uses escaping tracer gas to identify micro-leaks in the range of 1x10-4 to 10-9 scc/s.
-
product
NFC Physical Layer Test System
IQnfc+
LitePoint provides turn-key software that facilitates test coil calibration, executes test plan and provides detailed waveform analysis and flexible APIs to customize test flow in the labs.
-
product
DC Hysteresis Graph Test System
DX-2012H
Automatic measurement of the demagnetization curve of permanent magnetic material such as ferrite, AlNiCo, NdFeB, SmCo, etc. Accurate measurement of the magnetic characteristic parameters of remanence Br, coercive force HcB, intrinsic coercive force HcJ and maximum magnetic energy product (BH)max.
-
product
Advanced Driver Assistance Systems (ADAS) Testing
Advanced Driver Assistance Systems (ADAS) TestingAll modern vehicles are now being equipped with Advanced Driver Assistance Systems (ADAS). The development of such systems requires complex testing, including the ability to control and calculate relative positions between multiple vehicles and objects in real-time. We provide an effective solution for ADAS testing with highly accurate GPS positioning systems to measure relative positions and velocity between multiple vehicles and objects.
-
product
Electrodynamic Vibration Test Systems
CV-series
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
product
Vehicle Test Systems
What counts in development processes is the speed at which new vehicles and new technologies are made ready to go into production. For vehicle testing, this means that complex test problems must be solved. HORIBA develops vehicle test stands that simulate the realities of driving in the most varied situations both precisely and economically.
-
product
Pull Out Device
BCL-1
This Pull out device BCL-1 is designed and manufactured according to relevant standard requirements of IEC884-1/ GB2099.1-2008 and other electrical accessories standards, Mainly used to test the needed maximum force when the plug pull out from socket and the minimum force when single stage plug pull out from socket, and to inspect whether the socket can withstand the lateral stress imposed by electric plug into the socket. This device is applied to plugs and sockets which rated voltage no more than 250V and rated current no more than 16A.Specifications: • Weights: 36N*1, 5.4N*1, 5N*2, 4N*1, 2.6N*1; • Standard testing plug: each one for Dipolar 10A, tripolar 10A and 16A • Standard test bolt: Each one for 1.5N and 2N • 1 set of clamping device • 1 set of Weights tray • Lateral stress weights 5N*1 • 1 set of lateral stress bar
-
product
Mixed Signal Test Systems
MTS1010i
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
product
Discrete Switch Cards
Compatible for use on the VXI, LXI, and GPIB platforms, these switch products were formerly sold under the Racal Instruments brand name.
-
product
Electrical Protective Equipment Test Systems
СВС-50М (СВС-100М)
CBC-M-series systems are designed for high-voltage testing of electrical protective equipment and insulated hand tools. Withstand tests are carried out with AC voltage (CBC-50M: UAC ≤ 50 kVRMS; CBC-100M: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
product
Switching System Test Tools
EBIRST™
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
product
Modular Test System
The GS-X modular system is used for functional testing of medical devices and for testing the electrical safety of medical and general portable devices.
-
product
Power mixed test system
Power device or module with which are digitally controlled and memory can be measured per system.
-
product
Semiconductor & Electronic Systems Test and Diagnostics Services
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
