-
product
Ferrite Devices
Ducommun's products include very broad ferrite device selections to cover 100 MHz to 110 GHz operation frequency range. These devices include narrow band drop-in (FID and FCD), connectorized (FIC and FCC), junction (FIW and FCW) isolators and circulators and iso-adapters (FII and FCI). The broad bandwidth versions are offered as full band junction isolators and circulators (FIF and FCF) and Faraday isolators (FFF). These devices feature low insertion loss, high isolation and wide operating temperature range. Low cost and volume production versions of these ferrite devices are available per customers’ request.
-
product
Mezzanine System Carrier
MMS8010 / MMS8011
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
product
Slip Ring Test System
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
product
IPX5 IPX6 Water Spray Test Device
CX-IPX56B
Shenzhen Chuangxin Instruments Co., Ltd.
Drop rain rain chamber Uses: This equipment is main to test the physical and other related properties of the products in the environment of simulated rain, such as electronic and electrical products, lamps, electrical cabinets, electrical components, automobiles, motorcycles and their parts and components. After the test, through the test result to determine
-
product
Oil Test System
The Oil Test system Model OTS 2K1 is portable transformer oil Test system. It is a specially designed for accurate measurement of Loss Factor, Permitivity & Volume Resistivity Measurement of Transformer Oils & Petroleum jellys. The test frequency is 50 Hz . The system is provided with Mode Selector Switch so that once the oil cell is connected, it can measure all Three parameters in different modes without handling the test leads.
-
product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
product
Pump Test System
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
product
Loading Devices
Educated Design & Development, Inc.
Built-in fans provide sufficient coolingSelf-contained unit eliminates hazards due to exposed wiringFine tuning mechanism allows for ultra precise measurementsUnits are on casters, providing a portable test station!
-
product
Testing And Inspection Devices
HEIDENHAIN offers testing and inspection devices that deliver all setup, monitoring, and diagnostic data needed for the analysis of its encoders. Grid encoders from HEIDENHAIN are ideal for machine tool inspection and acceptance testing, accurately measuring CNC machine tool movements in both static and dynamic inspection.
-
product
Mechanical Shock Test System
BW-MST-E5000
The Mechanical Shock Tower develops the kinetic energy electromagnetically. An iron core "bullet" is attracted to the magnetic core of the solenoid by the dense magnetic field that is created as current flows through the field coil of the shock tower. As the bullet is drawn into the center of the magnetic field the acceleration increases exponentially as the gap reduces to zero on impact causing the high impact shock
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
Plug Pin Durability Test Device
IEC60884 Fig30
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig30 plug pin durability test deviceSuitable for checking the tightness of the plug pin,Check the tightness of the plug pin according to the standard, and customize the pin hole gauge of other national standards.
-
product
Automatic Transformer Test System
TH2829CX
Changzhou Tonghui Electronic Co., Ltd.
Number of Test PIN: 20 ■ Frequency: 20Hz-1MHz, Resolution: 0.5mHz ■ Signal Level: 5mV-2Vrms(Option:2mV-10Vrms) ■ Test Speed: max. 13ms ■ 7-inch TFT LCD display with a resolution of 800×RGB×480
-
product
Compliance Test Systems
LMG Test Suite
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
product
Low Voltage Test System
CKT T1
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
product
Medical Device Testing
Product Safety Consulting Inc.
Product Safety Consulting guides you through the process of obtaining safety certification in the fastest time and for the least cost. We have years of experience testing products according to FDA 501K, UL/IEC 60601 and 61010. We help you not only verify the classification of your medical device, but get you through the conformity assessment process – from designing for compliance, to applicable essential requirements, to testing your product, to achieving certification.
-
product
Automated Test System
Automated Test System is a production-ready solution that combines test software and various hardware for validation test in both manufacturing and R&D. The solution provides a high performance and cost-effective system based on National Instruments technology.
-
product
Custom Motor Test Systems
Magtrol's Customized Motor Test Systems (CMTS) are PC-based, turnkey systems custom designed and built to meet your specific motor testing requirements. By integrating Magtrol's motor test equipment with power supplies, adaptable fixtures, custom tables/cabinets, printers, etc., Magtrol's engineering team can customize PC-based, turnkey systems and modular test benches for almost any motor test application.
-
product
EV Power Components End of Line Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
product
Engine Emission Test System
By adding transient operation functions (self-learning/predictive driving + each test mode performing) to measurement•control panel, Ono Sokki can build up engine test system that can perform transient mode tests supporting worldwide gas emission controls including TRIAS, FTP, EURO, and ISO. (e.g. WHDC, NRTC).This system provides good reproducibility for Transient mode test. Delay compensation and rotation inertia compensation function have greatly improved as well as self-learning / predictive driving function.Automatically processes from measurement to data output of test result, in conjunction with gas emission analyzer, tunnels, gas emission particle measurement system, smoke meter, etc.
-
product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
product
PCIe 4.0 Test Platform
PXP-400A
The Teledyne LeCroy PXP-400A Test Platform provides a convenient means for testing PCIe 4.0 cards with a self-contained portable and powered passive backplane. The PXP-400A provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer.
-
product
Socket Outlet Torque Test Device
CX-LJ
Shenzhen Chuangxin Instruments Co., Ltd.
For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets, in accordance with IEC 60065 clause 15.4.1 and figure 11, IEC 60335-1 clause 22.3, IEC 60884-1 clause 14.23.2.
-
product
(25kN) Fatigue Testing Systems
8872
The 8872 fatigue testing system is ideal for fatigue and static testing of biomedical, advanced materials, and manufactured components. The servohydraulic actuator is conveniently located in the crosshead for easy table mounting. The T-slot base makes it easy to secure orthopaedic specimens, automotive components, and manufacturing assemblies. The adjustable crosshead, actuator-mounted load cell, and corrosion resistant T-slot base with unique drain channel are essential for testing biomedical specimens immersed in a saline bath.
-
product
Standalone Test System
1000 Series ATE
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
product
In-line vacuum test systems
Ensuring that products meet the highest quality standards is absolutely essential in the manufacture of food, pharmaceutical and cosmetic products in particular.Leak-tight product containers have a major role to play here. Leak-tight product containers have a major role to play here. Leakages allow the contents of a container to get out, but more importantly they also allow germs to get in, rendering the contents unusable.INDEC vacuum test systems monitor containers for leak tightness fully automatically within the production process. A wide range of containers, including bottles, jars and cans as well as tubs and trays, are tested for leak tightness by means of a non-contact inspection.The means to this end is a pre-existing vacuum or a vacuum created in the container expressly for the purpose of leakage testing. Containers which are not leak-tight are reliably identified and automatically rejected.These processor-controlled test systems are highly reliable and extremely easy to use, qualities which have played no small part in making them the first choice already for many companies throughout the world.
-
product
High-Voltage Test Device
PGK 70 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
product
AC Voltage Test Systems
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
product
High-Voltage Test Device
PGK 110 / 5 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing as DC or Dc testing device* Polarity of the DC voltage can easily be reversed* Robust and durable
-
product
High-Voltage Test Device
PGK 150 / 5 HB
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR PGK H. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 150 kV output voltage with positive or negative polarity* AC voltage testing - up to 110 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
