Bluetooth Low Energy
minimal power required WPAN. Also known as: BLE,Bluetooth Smart
See Also: Bluetooth, Bluetooth Test, WPAN
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
Portable Test Bench For Single Phase Energy Meter
SY 2100
Hong Kong Songyang Industrial Ltd.
Anthropomorphize design, Large size LCD display, easy operation. High stability, good reliability. Reasonable internal structure. Compliance with IEC736.ISO9001 certificate. Automatic switchover of voltage or current output to protect equipment when voltage circuit short or current circuit open and alarm display on LCD
-
product
Low Noise Voltage Preamplifier
1201
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
-
product
Low Noise Amplifiers
Chengdu KeyLink Microwave Technology Co., Ltd.
KeyLink's low noise amplifiers typically exhibit noise figures below 5.5dB and output 1dB compression points up 8dBm. These amplifiers are economical choices for general purpose applications. KeyLink's low noise amplifiers can be categorized as follows.
-
product
47~1050MHz FTTH Top Ultra Low Light Receiver
H9122TG
Hangzhou Huatai Optic Tech. Co., Ltd.
H9122TG, operating bandwidth of 47 ~ 1050MHz, is a top-level type, ultra low optical CATV receiver, regardless of the aircraft for analog television or digital television, have high reception sensitivity and excellent intermodulation distortion index. Built-in light AGC, a high optical power when receiving, play limiter output, so H9122TG at + 2 ~-24dBm large dynamic range of received optical power, and have excellent characteristics.
-
-
product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
product
Energy Detector Laser Energy Meters
11QE25-LP-S-MB
11QE25-LP-S-MB energy detector provides a unique combination of high damage resistance and high speed. It also offers very good linearity with power and a versatile mounting system. It is right for many pulsed lasers. It is right for many OEM, manufacturing and laboratory uses.
-
product
Portable Single-Phase Energy Standard
PEWM-3C-1
The single-phase energy standard PEWM-3C-1-1 is used for a quick check on site of all types single-phase electricity meters – for active, reactive or apparent energy, electromechanical and electronic. The voltage and the current are measured at the same time. The current can be measured directly within 10A or 100A range or with current clamp to 100A. The current clamp is electronically compensated.
-
product
Low Concentration Type HF/HCl/NH3 Concentration Monitor
HF-960M
The HF-960M uses sensors that offer outstanding corrosion resistance for high-precision, high-speed measurement of low concentrations of hydrofluoric acid, hydrochloric acid and ammonia, and is thus perfect for single-bath and wafer cleaning. The HF-960M is also an environmentally-friendly product that uses lead-free solder for mounting chips on the PCB.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
product
Low Resistance Ohm Meter
6237 DLRO
Standard Electric Works Co., Ltd
The 6237 DLRO is a "full feature professional instrument". The RUGGED and "O-RING" SEALED Digital LowResistance Ohm and Contact Meter is specially designed to measure very low resistance accurately and give the result directly on the large and clear LCD. The 6237 DLRO makes measurements by passing a constant current through the device under test (generally a conductor, contact or low resistance) and measuring the voltage across it. The Low Resistance is then calculated by ohm's law. This superb instrument is powered by rechargeable battery. It is supplied complete with instruction manual. This ensure that every product is not just fully functional and calibrated after the assembly lines, but also within tight specifications tolerances before leaving the strict quality control of Standard Electric Works.
-
product
Low Phase Noise Amplifiers
Low Phase Noise amplifiers are critical for many applications requiring high signal integrity. This is especially relevant in instrumentation, defense, and telecommunication applications where low phase noise amplifiers are becoming increasingly important as the oscillators improve. Phase noise is described as the close-in noise to the carrier that can often appear as jitter on a clock signal. Analog Devices offers a large portfolio of low phase noise amplifiers to meet a variety of requirements in the LO network, receiver, as well as in the transmitter. Our portfolio supports a wide range of power levels and frequencies to provide the right solution for the given application.
-
product
High Energy Industrial CT X-Ray Inspection System
MeVX Series
The most advanced industrial DR & CT systems in the world are now available with Linear Accelerators. Offered with energies up to 9MeV, the MeVX series of systems provide the same ease of use as our low energy systems in a high energy format. Utilizing our current efX software platform along with the superior service, support & training that we are known for puts these systems in a class of their own.
-
product
Low Power Programmable AC Source with Transients
61500 Series
Chroma Systems Solutions, Inc.
Power:500VA (61501)1500VA (61503)2000VA (61504)4000VA (61505)Voltage range: 0-150V/0-300V/AutoCompact size and weight attributable to advance PWM technologyAC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyLow output impedance for testing IEC 61000-3-2 (61505)Programmable output impedance for testing IEC 61000-3-3LIST, PULSE, STEP mode function for testing power line disturbance (PLD) simulation capabilityIEC 61000-4-11 voltage dips, short and variation simulationHarmonics, inter-harmonics waveform synthesizer for testing IEC 61000-4-13Programmable voltage, current limitComprehensive measurement capability, including current harmonicsHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientAnalog programmable interface3 units combined to 3-phase power outputEasy-use software for operation and IEC regulation testOptional GPIB and RS-232C interface
-
product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
product
3.4 MP Autofocus Low Light USB Camera Board With Liquid Lens
See3CAM_30
See3CAM_30 is a 3.4MP UVC Compliant, low light, autofocus USB camera with liquid lens. It is a two-board solution with AR0330 CMOS image sensor from ON Semiconductor and USB 3.1 Gen1 type C interface board. See3CAM_30 is a colour camera with S-mount lens holder and does not require any special camera drivers to be installed in the host PC. See3CAM_30 is customizable and it is a Ready-to-Manufacture camera with all the necessary firmware built in and compatible with the USB Video Class (UVC). It consumes less power and doesn't heat up. There is no mechanical movement like in VCM motor for autofocus. Hence the life of the lens increases.
-
product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340L
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
product
76kWh Lithium Battery 384V 200AHSolar Energy Storage LiFePO4 battery System
SPVLI-76KWH
Zhejiang Sandi Electric Co., Ltd
SANDI ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
-
product
SPD High, Medium, and Low Voltage TOV Test Equipment
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems part 1: Performance requirements and testing methods)TOV fault test equipment1. Three-phase isolation test transformer2. Single-phase test transformer3. Low voltage switchgear4. Power controller5. Test voltage and current measurement6. Sample box
-
product
MPOD Universal Low And High Voltage Power Supply System
MPOD--LVHV
In addition to the well established 6-, 8- and 12- channel "medium power" low voltage power supplies of the PL506, PL508, PL512- and MARATON - series WIENER presents with Mpod a new, universal multi-channel low voltage (LV) / high voltage (HV) power supply system.
-
product
Energy Meter
The energy meters were specially developed for measuring energy on board electric traction vehicles. You can measure both the DC and the AC signals of any existing traction power supply system (1.5kV DC, 3kV DC, 15kV / 16.7 Hz, 25kV / 50 Hz). In addition, they are also suitable for multi-system locomotives with more than one electrification system.
-
product
T3 Low & High Voltage Differential Probes
T3 Series
Teledyne Test Tools Low & High Voltage Differential Probes offer end user versatility with all models powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range consists of one Low Voltage and three High Voltage models with varying bandwidths to satisfy a wide array of customer applications.
-
product
Waterproof Eco Tester EC Low
EcoTestr EC Low
The Eutech EcoTestr EC series comes with rugged, sturdy stainless steel pin sensors, giving you quick, reliable conductivity measurements. Ideal for use in a wide range of conductivity applications, such as hydroponics gardening, fish-farming, pools, electroplating and other water/ wastewater applications.
-
product
PCI Express, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device for Windows - Low Profile, Onboard GBIP Analyzer
780936-01
The PCIe‑GPIB+ combines an IEEE 488 controller and an analyzer on one device for computers with PCIe slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The PCIe‑GPIB+ achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
Field Calibrator of Three Phase Energy Meter
SY3640
Hong Kong Songyang Industrial Ltd.
SY3640 three phase energy meter field calibrator is a high precious three phase energy reference meter; it uses the advanced technology and latest electronic components available in the world, and use high speed DSP as the main processor to ensure the accuracy and long time stability.
-
product
Low Constant Temperature Trough
DRK6691
Shandong Drick Instruments Co., Ltd.
Drk6691 small low constant temperature trough is a special product designed for small Abbe refractometer, supporting the use of. It has many advantages such as constant speed, constant temperature, small volume, low noise and convenient operation and so on , so it is a higher price products. This product adopts the technology of the one chip computer, PID selftuning regulation technology;adopts imported platinum resistance temperature (Pt100), so it has high precision of temperature control and temperature fluctuation is small; adopts the semiconductor refrigeration technology, so that it consists of advantages of fast refrigeration, no noise.
-
product
Stainless Steel Low Pressure Gage
SGX
The Series SGX Gages have dual English/metric scales with ±1.6% full scale accuracy. The Series SGX gages are designed with 304 SS housings and brass wetted parts. Units can withstand ambient temperatures up to 149°F (65°C) and process temperatures up to 212°F (100°C).
-
product
ML/AI Low Power FPGA
iCE40 UltraPlus
*Flexible logic architecture with 2800 or 5280 4 input LUTs, customizable I/O, up to 80 kbits of embedded dual port memory and 1 Mbit of embedded single port memory*Ultra-low power advanced process with static current as low as 75 uA and 1-10 mA active current for most applications*High performance signal processing using DSP blocks with multiply and accumulate functions*Soft Neural Network IPs and compiler for flexible Machine Learning/AI implementation*FPGA design tools, demos and reference designs to kick start designs
-
product
Series Low Frequency Vibration Sensors
AC136
Low Frequency Accelerometer, Side Exit Connector / Cable, 500 mV/g
