-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
Nano Interface Unit
NIU1A
-
NAI's NIU1A is a nano unit with an integrated power supply, one function module slot, and an optional ARM Cortex-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications, and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in less time, with NO NRE.
-
Product
Manual Clemen Unit
Elcometer 3000
-
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
Product
PXI Functional Test System
U8989A
Functional Test
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
Product
Electronic Units
-
Electronic units for field installation and mounting rack installation control the actuators. They are fed with 115 or 230 V AC. A local control panel allows for easy basic settings.
-
Product
Flue Gas Parameter Unit
TPF-100
-
The TPF-100 product (Instrument/Apparatus) integrates a measurement module for three parameters: temperature, pressure, and flow rate. With only one measuring aperture, the compact design allows the measurement of three parameters, and its advantages include easy installation and maintenance.
-
Product
8Ch Speaker/Receiver Unit Tester
BK9012
-
Based on the BK2120A Audio Analyzer, the BK9012 is designed to quickly test microspeakers or receivers 4~8 at a time at a rate that you’ll find hard to keep up with. It tests various frequency characteristics and also rub & buzz so you know the quality of your product is maintained. And of course, you can track the accuracy and stability of your process using the data you’ve saved on about 4 million microspeakers (based on a 6 second total test + load time) per month.
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Test Fixture
Stopper kit includedYAVCANCON2 for fixture identification not included
-
-
Product
INERTIAL MEASUREMENT UNIT
MS-IMU3020
-
The MS-IMU3020 delivers market leading price to performance in an ultra-compact aluminum package. The gyro bias instability of 0.9 /h and accelerometer bias instability of 9 g supply ample performance to support a range of applications from UAS navigation and control to pipeline inspection.
-
Product
Basic Unit - Medical Equipment Functional Test Module System
GS-X
-
The GS-X Testing System consists of a Basic Unit and various plug-in test modules which the user can purchase as required. The range of functions of these Module-Box is being continuously expanded, and presently includes functions for testing the following devices: - Infusion pumps, Cardiac pacemakers, Defibrillators, High-frequency Surgical equipment, electrical safety ECG Simulation, Equipment for electro-stimulation.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Calibration & Testing Unit for AC & DC Meters
-
Supreme Instrument Laboratories
Calibrator for calibration and testing of A.C. Milliammeters, Ammeters, Voltmeters, and D.C. Microammeters, Milliammeters, Ammeters, Millivoltmeters and Voltmeters having following technical specification
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
The One Unit 19" Enclosure
Slimkit-10
-
The 1 U (unit) 19" system enclosure combines flexibility with a comprehensive EMC protection. Applicable as 19" rack enclosure or as desktop device. It is made of sheet metal and the aluminum front panel can be customized.
-
Product
ESI(Electronics Systems Integration Unit)
MS 2004
-
The ESI subsystem provides platform interfaces like Gyro and on board Radar Blanking. This unit receives Analog and Digital GYRO inputs from ship and pre- trigger pulses from on board radars of the ship. This unit measures and provides the ship heading data to VARUNA ESM system. It also provides Heading, Roll and Pitch data to the ECM system. This unit also generates band wise composite ESM Rx. Blanking gates and provides all the required interfaces to ESM receiver, ECM System and System Controller units.
-
Product
Precision Source/Measure Unit (SMU)
B2900A Series
-
The Keysight B2900 Series precision source measure unit (SMU) provides superior performance and usability at a reasonable price. These compact benchtop SMUs enable you to quickly take various I-V (current versus voltage) measurements requiring high resolution and accuracy. Easily view results on the user-friendly, color LCD graphic interface without changing connections.
-
Product
High Temperature Component Test Fixture
16194A
Test Fixture
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Radar Test System
UTP 5065
Test System
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
Product
Multichannel Source Measurement Unit
AXS7720
-
Extremely low noise with linear output stageVery fast rise and fall timesProgrammable current pulseIntegrated current measurement unitIntegrated voltage measurement unit
-
Product
Multiplexed Measurement Unit
YAV90MMU
Multiplexer Module
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
-
Product
Chassis/ Base Unit
-
iDAQ-900 Series base units (USB, Ethernet, standalone) offer plug-and-play setup and 10–30VDC input for easy deployment in industrial use.
-
Product
Antenna Tuning Unit
MS 2012
-
Antenna Tuning unit is used to automatically tune the notch antenna impedance. Microprocessor does tuning through tuning inbuilt algorithm. It has RS485 interface for external control unit interface. Capacitor unit (CU), Inductor unit, (IU) and RF Element are subunits of this antenna-tuning unit. System maximizes transmission.
-
Product
Crawler Control Unit
CCU186
-
The CCU186 control unit for crawlers possesses a distinct advantage compared to existing products. In fact, all of the performances that are usually achieved with standard control units are now available in the crawler configuration. Automatic slow preheating, the progressive rise in voltage with each exposure, as well as a selection of set values are all included in the CCU186.As the CCU186 has been entirely fitted with industrial electronic components, it is perfectly suited to the often extreme conditions of automatic intra-tube control campaigns.
-
Product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
Source Measure Unit
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Generator Monitoring Unit
-
Avoids the requirement of 2 different meters (energy and VAF in one)Reduces the cost and simplify wiringHigh resolution reading with auto scaling in LEDEnergy consumption in counter even if CT is reversed
-
Product
Inertial Measurement Units
IMU
-
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
Product
Battery Loading Unit
BLUe
-
BLUe series Battery Loading Units; portable instruments for controlled & monitored discharge of batteries. It is designed for integrated site discharge test, design & QC test and also for monitoring discharge process of battery bank with connected load. Single autonomous unit having inbuilt display, keypad and wireless communication with PC makes it very easy to use. It comes in different configurations ranging from 12V to 380V discharge voltages and 50A to 300A discharge currents. Various options are available to control & monitor the discharge process. With the help of optional Cell Monitoring Unit - CELLMon, voltage of each individual cell can be monitored & data sent to main BLUe unit and then from main unit to PC via wireless communication. Each BLUe unit is supplied with PC downloading & analysis software for real time monitoring of discharge process.
-
Product
Motion Reference Units And Wave Sensors
MRU And WS
-
The Motion Reference Unit (MRU) product line was first released in 2004 when Inertial Labs MEMS-based sensor solutions began to compete in performance with traditional FOG units. Easy integration of the MRU product line for the end user means competitive performance at no extra cost.
-
Product
Multichannel Source Measurement Unit
AXS844x
-
Run tests simultaneously on 4 channels with up to 400 V. Carry out measurements directly on the DUT with the integrated VMU and CMU. Perfect for direct testing of high-voltage RGBW LEDs
