Serial Interfaces
one conductor one bit at a time data transfer.
See Also: Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Adapters, PXI Serial Interfaces, Parallel Interfaces
-
Product
Intelligent Power Monitor
iPM
Power Monitor
NAI’s iPM is an Intelligent Power Monitor that provides a precise, instrument grade, digital analysis of input power lines. This advanced, DSP-based unit monitors single-phase, 3-phase 4-wire wye, or 3-phase Delta power lines at various input voltage levels and frequencies.The iPM is equipped with an EIA RS485-compatible serial communications interface that permits additional control functions and readout of diagnostic data, and features a Background Built-in-Test (BIT) that constantly monitors the health of unit hardware and software. This power monitor is designed and qualified to the most stringent performance and environmental requirements, and is ideally suited for rugged defense and industrial applications.
-
Product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC, Virtex-7 FPGA - XMC
Model 71762
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable serial gigabit interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Also available in 3U VPX, 3U & 6U cPCI & PCIe- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe- See comparable Jade Xilinx Kintex UltraScale FPGA Module: Model 71862
-
Product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - XMC
Model 71671
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- Dual uSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface, up to x8- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Ethernet Extensions
-
CXR offers a full range of access solutions and Ethernet extension on any type of media - copper, fiber optics and wireless, as well as through a network TDM PDH / SDH or linkage via modem serial interface X21 / V35.
-
Product
SDI Cable Drivers
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a wide range of products specifically designed for driving Serial Digital Interface (SDI) video signals across long copper cables. These multi-rate products are the ideal solution when designing high definition (HD) and ultra high-definition (UHD) video broadcast equipment and are fully compliant with the Society of Motion Picture and Television Engineers (SMPTE) standards.
-
Product
Low Profile PCI Express 4-Port
7402e
-
The 7402e low profile PCI Express serial interface provides four serial ports, each individually field-configurable for RS-422 or RS-485 communications. The board uses a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
42-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
I-87K Expansion Racks
-
ICP DAS offers a multitude of serial expansion racks for use with I-87k I/O modules. By implementing external serial expansion racks, users are able to easily implement a greater amount of I/O onto an existing industrial control infrastructure. The I-87K series are serial interface modules and are supported on PAC (Programmable Automation Controller) units.
-
Product
Floating-Point C6678 DSP Module
FMC667
-
Sundance Multiprocessor Technology Ltd.
The FMC667 is a Digital Signal Processor FMC daughter card based on the Texas Instruments TMS320C6678 device. The FMC667 daughter card is mechanically and electrically compliant with the FMC standard (ANSI/VITA 57.1), and can be used in a conduction cooled environment. This FMC is equipped with power supply and temperature monitoring and offers several power-down modes to switch off unused functions and peripheral interfaces. Several Gigabit differential pairs from the FMC connector are used to implement a PCIe and Serial Rapid IO interface between the FMC and the carrier.
-
Product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
-
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
Product
Smart GPIB Serial Interface Board
Model 4806
-
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
Product
PCI Express 16-Port RS-232 Serial Interface
7161e
-
The 7161e provides sixteen RS-232 serial ports capable of data rates to 460.8K bps. Each RS-232 port implements all modem control signals for maximum compatibility with a wide range of peripherals. The board is PCI Express X1 compliant and utilizes 16C854 UARTs to provide 128-byte Tx/Rx FIFOs for maximum reliability in data intensive applications.
-
Product
2-Channel 3.6 GHz or 4-Channel 1.8 GHz 12-bit A/D with DDC - 6U VPX
Model 58641
-
- Ideal radar and software radio interface solution- Two 1-Channel mode with 3.6 GHz, 12-bit A/Ds- Four 2-Channel mode with 1.8 GHz, 12-bit A/Ds- Programmable one-channel DDC (digital downconverter)- 4 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 6U VPX
Model 57660
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
3U CompactPCI Serial 9th Gen Intel Xeon®/Core™ i7 Processor Blade
cPCI-A3525 Series
Processor Blade
CompactPCI® Serial (PICMG CPCI-S.0) is a new modular computer standard officially adopted by PICMG in 2011. The CompactPCI Serial standard defines a completely new connector to support high-speed serial interfaces including PCI Express, SATA, USB and Ethernet. A CompactPCI Serial backplane has six high-speed connectors P1 to P6 on the system slot but only P1 is mandatory on peripheral slots, P2 to P6 being optional. A CompactPCI Serial system can comprise a total of nine blades (one system blade and eight peripheral I/O blades) through an Ethernet full mesh or single star architecture. The CompactPCI® Serial standard is the next-generation of the CompactPCI® specification and provides more flexibility and higher speed and bandwidth in modular system solutions.
-
Product
ARM LPC2294 Based Board
MS 2500
-
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
Product
Digital I/O
-
Curtiss-Wright Defense Solutions
Our digital I/O cards include interfaces to LVDS, Camera Link, Serial interfaces, and customizable I/O. Built leveraging our decades of experience producing highly rugged COTS signal acquisition hardware, our PMC and XMC modules are designed to perform reliably in the toughest operating environments.
-
Product
NI-9870, 4-Port, RS232 C Series Serial Interface Module
779891-03
Serial Interface
The NI‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
Product
Serial To Digital Interface MiniBox™
-
ICS's 2363 Serial Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
Product
4-Channel 500 MHz A/D and 4-Channel 800 MHz D/A with Virtex-6 FPGA - 6U VPX
Model 58650
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
SparkFun Dev Board
ESP8266 Thing
-
This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors, or automate coffee makers, and with an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any Internet-connected project. To top it all off, the ESP8266 is incredibly easy-to-use: firmware can be developed in Arduino, and uploaded over a simple, serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
SDI Cable Equalizers
-
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of professional video products includes cable equalizers specifically designed to compensate for the losses that Serial Digital Interface (SDI) video signals accumulate when transmitted across long 75Ω copper cables. These multi-rate products are the ideal solution when designing high definition (HD) and ultra high-definition (UHD) video broadcast equipment and are fully compliant with the Society of Motion Picture and Television Engineers (SMPTE) standards.
-
Product
ARM 9 System on Module
MS 1515
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
Product
2-Ch 1 GHz A/D and D/A with Virtex-6 FPGA - 6U VPX
Model 58630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 1 GHz 12-bit A/D- Two 1 GHz 16-bit D/A- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
Model 5983
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- 9 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Kintex UltraScale FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
sbRIO-9870, Non-Enclosed, 4-Port, RS232 C Series Serial Interface Module
780922-01
Serial Interface
The sbRIO‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The sbRIO‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. Non-enclosed modules are designed for OEM applications.
-
Product
Low Profile PCI Express 2-Port
7205ec
-
The 7205ec low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7205ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
