System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
Cable-End Test Fixtures
-
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Digital Insulation and Continuity Tester
Metra Insu 20
-
Measurement of the insulation resistance on electrically dead equioment and systems with test voltages up to 1000 V. For testing motors, transformers, generators, switchgears. For testing of house hold appliances. Measurement of the insulation resistance of cables. Very useful for on-site maintenance and service departments.
-
Product
Melt Flow Testers
-
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
Product
Copper Diffusion TestSystems
-
Materials Development Corporation
MDC announces the addition of software and hardware for copper diffusion studies to its CSM/Win suite of semiconductor test systems and software. This new CSM/Win feature plays an important part in the development of processes and materials for the next advance in integrated circuit technology that employscopper as a conductor. Special Current-Voltage Bias-Temperature Stress (IV-BTS) software can measure the degradation of insulator quality due to copper diffusion.Multiple test sites can be stressed with a constant voltage while the current through each site is measured and recorded. The Current-Voltage Bias-Temperature Stress test supplements conventional MOS C-V measurements and Triangular Voltage Measurements (TVS) that are also employed in copper diffusion studies.
-
Product
Seno-Con Test System
PANTHER 2K QST
Test System
Qmax Test Technologies Pvt. Ltd.
Panther 2K-QST is a versatile ultra fast Seno-Con test system designed to test high volume ,low to high pin count consumer semiconductor IC’s for its assembly line wire bonding faults. Its innovative test technology helps learn from known good device and test against target device drastically reduces time required to develop Test programs.The operating software is designed in such a way that it is fully user friendly with GUI programming.
-
Product
Miniature Vibration Test System
G-2 Series
-
The G-2 Series Miniature Vibration Test System, though compact & handy, consists of a sweep oscillator, sine controller, power amplifier and vibration generator, thus suited to a variety of applications; calibration of sensors, standardized vibration tests for small parts, school teaching materials and modal analysis. The G-2002 is handy, with all the composed units being incorporated in a portable case.
-
Product
Targets
-
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Product
Stator & Coil Testing
-
Electronic Systems of Wisconsin, Inc.
ESW Stator Test Systems come fully equipped with the latest industry features. The on-screen display in our testers allows the operator to visually see the part lead hook-up to the tooling connections. Our software makes it easier to read, track, and record your stator test information. While performing tests, you can watch the testing throughout the process in real time. You can view various wave-forms for surge or magnetic field, which can be displayed real-time and printed if desired. The software logs all test results, so that you do not have to worry about losing important information. ESW designs the tooling to be simple to connect the part. We work closely with you to define and implement your customized testing needs. The videos and slideshow below show some of our Stator Testers.
-
Product
Scalable Multi-Channel Active Thermal Control (ATC)
T-Core Thermal Control System
-
Cohu’s proprietary T-Core thermal system’s controller provides precise, multi-site temperature management of power dissipation ICs, such as graphic chips and CPUs, optimizing test yield.The T-Core thermal control system optimizes test yield at cold, ambient, and hot temperatures and offers better than +/- 1°C accuracy with response speeds of >125°C/sec. The system’s flexibility to control air, liquid, and refrigerant based thermal heads gives semiconductor manufacturers excellent temperature control capability for high volume manufacturing.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope
780319-01
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
Automated Tester
-
With high labor costs in Europe and the US, and the surge in labor cost in Asia, automated test solutions are in demand. Automated systems also improve traceability and reduce operator mistakes.The combination of automation with high throughput test systems is perfect to extend the usage of Flying Probe Testers to mid size production/sample volumes.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Test Systems
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm
40-294-022
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Phase Noise Analyzer
NXA-6
-
This new NXA-6 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 6 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
Product
Pneumatic Subsystem
OTP2-Modul-Nr050
-
With the pneumatic subsystem, a roller terminal, a maintenance unit, a main vent, a pressure reducer and 8 2/3-way vents are installed in the system. The extension of the module can create new possibilities for your test system.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 773kΩ
50-298-043
Programmable Resistor Module
The 50-298-043 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Dynamic Component Test Systems
-
RedViking brings advanced engineering and proven implementation expertise to your next dynamic component test stand. We’ve designed entire fleets of multi-model and single-model test systems for new component development and production as well as military and commercial MROs. We have decades of experience building and implementing turnkey dynamic component test systems, and we’ll work with your teams virtually anywhere in the world.
-
Product
Portable Charging Facility Testing Platform For Electrical Vehicle
-
PONOVO has long-term follow-up technology in China and abroad. Based on its own mature intelligent power detection equipment, and according to its own advantages in the field of new energy, PONOVO could be able to provide users with professional new energy test system solutions.
-
Product
PXIe-2738 , 256-Crosspoint, 8x32, 2-Wire PXI Matrix Switch Module
782835-38
Matrix Switch Module
256-Crosspoint, 8x32, 2-Wire PXI Matrix Switch Module—The PXIe‑2738 is a high‐density 8x32 PXI matrix switch module designed for routing signals within automated test systems and using electromechanical relays to perform immediate switch operations. It also offers features to monitor the health of deployed systems and plan for predictive maintenance, including onboard relay count tracking, a temperature sensor, and functional and resistive relay self-tests available through the NI Switch Health Center.
-
Product
Programmable Withstanding Voltage & Insulation Test
LS9923
-
LS9923 programmable withstanding voltage & insulation test system is high-performance testing device special for AC&DC Withstanding Voltage and Insulation Resistance Test, It allows setting the output voltage. The warning value,testing time and some other parameters can be set in the screen.It with a variety of automatic test functions. The testing is quick and high accuracy which is not only applied in the production line but also in the develop research.
-
Product
USB Modular Products Chassis
U2781A
Chassis
The Keysight U2781A USB modular instrument chassis is a high-performance 4U high chassis that comes with a 200 W universal AC power supply and a built-in protection circuit. This portable chassis can house up to six Keysight USB modular products. The U2781A targets a wide range of applications in both industrial and scientific environments in the research and development (R&D), design-validation, and manufacturing fields. The primary advantage of this chassis is its synchronization capability between modules. This can help you to lower your cost of testing and accelerate your test system integration and development.
-
Product
Handover Emulator
-
Qosmotec Software Solutions GmbH
The Qosmotec handover test system QPER is a versatile test platform for emulating the RF signal between radio devices in a wireless network, e.g., between mobile stations and radio infrastructure of a mobile network. It is employed in test beds where radio signals are transmitted through coaxial cables and specifically manipulated by testers. QPER can be based on various hardware platforms, from attenuator arrays to digital channel emulators.
-
Product
Furnaces
-
These three zone resistance wire wound furnaces are of split construction to facilitate fast and easy loading of a pre-assembled specimen train. The case is constructed from stainless steel with aluminium and hardened insulation board end plates. The optional front cut-out allows the use of side-entry high-temperature extensometry. Adjustable stainless steel latches keep the furnace halves locked together during use, but are then easily opened once testing is complete. The furnace is available with optional heavy duty brackets or mountings, which attach to a wide range of testing systems. An extensive range of standard controllers is available to suit most test regimes. Custom variants can be specified should the standard range not include a suitable unit.
-
Product
LED Optical Aging Test Instrument
LEDLM-80PL
-
LEDLM-80PL LED Lumen Maintenance and Aging Life Test System is designed according to standards of IES-LM-80, IES-LM-82, TM-21 and GB2312-80, and the software is developed base on Arrhenius model. LED has the features of long life, but with the different working condition and drive current, its life will be different, but generally the life will be around 50K hours. Differ from the traditional lightsource, LED light will decay gradually rather than extinguish instantly, so in the standard of LM-80, it introduces L70, L50 and etc.
-
Product
Test Fixtures & Jigs
-
A test fixture or test jig is the component containing the bed of nails used for testing the PCB or assembled product. It is powered and controlled by the Yelo Testpoint system which has test cards capable of providing multiple test conditions. This system also controls the probes used in the bed of nails, and relays test information back to the Testpoint system to be analysed.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable DC Power Supply
62000L Series
DC Power Supply
The Chroma 62000L Series Programmable DC power supplies have low noise linear performance and fast transient response. The units have many unique functions that are targeted for overall automated test system integration, automotive power electronics MCU/ECU, power semiconductors, wireless communications, etc. The 62000L Series is a high quality yet cost effective programmable DC Source, designed to meet the stringent requirements of the next generation of power electronics. The GPIB and USB control interfaces come standard with the 62000L Series, no additional purchase required. The 62000L Series can be easily remote controlled via either of these two interfaces. The 62000L weighs less than 2.5 kg, and its case measures 214.6W * 88.6H * 280D mm. Its light weight and compact size makes it easy to handle and stack safely.。
