Burn-In Boards
Printed circuit boards (PCB) filled with integrated circuit (IC) sockets for purposes of connecting an array of IC packages for burn-in test.
See Also: Burn-In, High Power Burn-in, Burn-In Sockets
-
Product
PCI Multifunction Board
PCI-1202H
-
The PCI-1202 series is a family of high performance data acquisition boards for the PCI bus. It features a continuous, 110KHz for low gain (40KHz for high gain), gap-free data acquisition under DOS and Windows. The PCI-1202 family has the same hardware architecture as PCI-1802. The PCI-1202 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1202 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
PCI Data Acquisition Boards
AD8CH12B-100DMA Series - Single low-spur 8-bit, 100 MS/s
-
Model AD8CH12-100DMA has eight simultaneous-sampling 12-bit A/D converters, and can continuously acquire and transfer hundreds of megabytes or even gigabytes of A/D data directly into host system memory at up to 100 MB/s, via 64 or 32 bit PCIbus DMA. It can acquire and transfer eight 8-bit A/D channels at up to 12.5 MSPS each (100MB/sec aggregate), or eight 12-bit A/D channels at up to 6.25 MSPS each, or four 8-bit channels at up to 25 MSPS each, or four 12-bit channels at up to 12.5 MSPS each.
-
Product
PC/104 OneBank Board
EMC2-ZU3EG
-
Sundance Multiprocessor Technology Ltd.
The EMC²-ZU3EG is a PCIe/104 OneBank™ SBC with a Xilinx Zynq SoC and a VITA57.1 FMC™ LPC I/O board. The main processing power of the EMC²-ZU3EG is a Dual Core ARM9 and combined with traditional FPGA fabrics/gates + High-Speed I/O interfaces, like USB2.0, HDMI, 1Gb Ethernet and SATA and provide an total solution for any Embedded Application.
-
Product
PCI Daughter Boards
DB-16R
-
The DB-16R is a 16 channel Relay Output Board. It consists of 16 form c relays for efficient switching of load by programmed control. It is connector and functionally compatible with our 785 series boards with industrial type terminal blocks. The DB-16R can be used by our A-82x board or any other compatible board. The relays are energized by applying a 5 volt signal to the appropriate relay channel on the 20-pin flat cable connector. Sixteen enunciator LEDs, one for each relay, light up when their associated relay is activated . This board provides a screw terminial for power to avoid overloading your PC's power supply.
-
Product
PCI Digital IO Board
-
*Bus Interface: PCI Bus*Counter/Timer: 16 Channels*Counter Size: 32 bit*Max. Source Frequency: 80MHz*Compatibility: 5 V TTL/CMOS*Discrete Inputs: 24 Channels*Discrete Outputs: 24 Channels*Pulse Generation: 12 Channels*Bi directional I/O's: 8 Channels*Oscillator stability: 50 ppm*Op-to isolation for I/O's*DMA buffered operation*16-bit data bus 32 bit Address bus for External Memory Interface*The Pulse Width and PRI of the pulses can be varied*The pulse generation frequency from 10Hz to 40MHz (25ns to 100msec)*The no. of pulses controlled from 1 to 255 pulses*All the pulse input and the output signals and Bi-directional write signals driven through Pin Driver*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Data Acquisition I/O Boards
-
General Standards Corporation is a leading supplier in data acquisition I/O boards, provides a complete family of data acquisition cards for sonar, industrial, and embedded applications on several form factors/busses, and for many operating systems. Functions available include analog I/O, serial I/O, and high speed parallel I/O.
-
-
Product
Smart GPIB Serial Interface Board
Model 4816
-
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
PCI Board
FastX1703-DIG
-
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
Product
PCI Multifunction Board
PCI-1602F/8K/S
-
The PCI-1602/1602F series is a family of high performance and high resolution data acquisition boards for the PCI bus. It features a continuous, 100KHz for PCI-1602 (200KHz for PCI-1602F), gap-free data acquisition under DOS and Windows. The PCI-1602 family has the same hardware architecture as PCI-1802L. The PCI-1602 provides 32-channel single-ended or 16-channel differential analog inputs. Like the PCI-1802 family, the PCI-1602 series features a "Magic Scan" function, M-function, X-function, and Continuous Capture function.
-
Product
SparkFun SAMD21 Development Board
RedBoard Turbo
-
If you’re ready to step up your Arduino game from older 8-bit/16MHz microcontrollers, the SparkFun RedBoard Turbo is a formidable alternative. At its heart, the RedBoard Turbo uses the ATSAMD21G18, which is an ARM Cortex M0+, 32-bit microcontroller that can run at up to 48MHz. With an impressive 4MB of external flash memory and a UF2 (USB Flashing Format) bootloader, the RedBoard Turbo provides you with an economical and easy to use development platform if you're needing more power than the classic RedBoard.
-
Product
PCI Daughter Boards
DB-24PR/12/DIN (with DIN-Rail mounting kit)
-
The DB-24R consists of 24 form C, electromechanical relays for efficient switching of load by programmed control. The contact of each relay can control a 0.5 A /110 V load or 1A / 24VDC. The relay is energized by applying a 5 voltage signal to the appropriate relay channel on the 50-pin Opto-22 compatible connector or D-Sub 37 connector . Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated . This board needs a +12VDC or +24VDC external power supply to avoid overloading your PC’s power supply.
-
Product
PCI Daughter Boards
DB-16P
-
The DB-16P is a 16 channel isolated digital input daughter board for the A-82X board or any 812pg, 711 726, 720 series board, and PCI-Bus Multi-function boards. The optically isolated inputs of the DB-16P consist of a bi-directional OPTO-coupler with a resistor for current sensing. You can use the DB-16P to sense a DC signal from TTL levels up to 24V. You can also use the DB-16P to sense a wide range of AC signals. You can use the board to isolate the computer from large common-mode voltages, ground loops and voltage spikes that often occur in industrial environments.
-
Product
Isolated Programmable Multifunction Counter Board, LACQUERED
APCI-1710-LAC
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmable Each of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
PCIe Carrier Boards
-
These non-intelligent carrier cards interface XMC and PMC mezzanine modules and Industry Pack Modules to a PCI Express bus in a PC-based embedded computer.
-
Product
Board
ARDUINO UNO WiFi REV2
-
The Arduino UNO WiFi Rev.2 is the easiest point of entry to basic IoT with the standard form factor of the UNO family. Whether you are looking at building a sensor network connected to your office or home router, or if you want to create a Bluetooth® Low Energy device sending data to a cellphone, the Arduino UNO WiFi Rev.2 is your one-stop-solution for many of the basic IoT application scenarios.
-
Product
Burn-in Systems
-
Incal Offers A Line Of State-Of-The-Art Burn-In Testing Hardware And Software For Retrofit And/Or Total, Customized Burn-In System Configurations.
-
Product
PCI Daughter Boards
DB-8225/1
-
Screw terminal boardusing 37 pin cable I/O ports for A-82X seriesPCI-1800 series. (16 channel single-ended or 8 channel differential)Blank padsfor break detectionlow-pass filtercurrent shut and voltage attenuation.On board cold junction circuit in analog input channel 1jumper selectable single-endeddifferential modeDimensions :118mm x 174mm
-
Product
Ethernet to Relay Interface Boards
Model 8064 OEM
-
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
Product
Board Drivers
9450-DRV
-
IOWorks board drivers are Abaco Systems' IOWorks data acquisition and control (DAQC) software driver. It is a hardware and operating system-independent driver designed to support the widest variety of I/O in the industry. The driver operates with many operating systems such as Windows NT/Windows 2000, QNX, VxWorks, and Linux, and delivers high performance and flexibility across multiple platforms such as CompactPCI, VME and PCI.
-
Product
RFSoC Board
VP431
-
VP431, the next generation of our highly successful VP430, is a 3U VPX commercial off-the-shelf direct RF processing system that features the 3rd-generation Xilinx Radio Frequency System-On-Chip (RFSoC). The VP431 maximizes I/O channel density, reduces the radio frequency signal chain complexity, and allows for heterogeneous processing capability.
-
Product
Configurable 3U OpenVPX Multifunction I/O Boards
-
NAI offers a variety of 3U VPX solutions, including rugged I/O Boards and SBCs - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
Product
SMT & THRU HOLELOADED BOARD TEST PROBES
SERIES 43
-
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
Product
PXI Express Board Virtex-5 ADC Module
SMT790
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
PCI Express Multi-Function Boards
PCIe-8622
-
PCI Express, 200 kS/s High-speed, 16-bit 8/16-channel Simultaneously Sampled Analog Input Board with 4/12-channel Isolated DIO
-
Product
Burn-in System
Sonoma
-
High power burn-in system with advanced testing functionality at DUT level for substantially lower cost and high performance using State-of-the-Art technology
-
Product
Burn-In Test Sockets
-
The selection of the test socket is critical to the performance of a device during qualification testing where electrical bias and signals are applied. Key factors such as mechanical compatibility, operating temperature, ability to withstand high moisture levels, signal speed and lead inductance/capacitance all need to be taken into account when selecting the best socket for the test application.
-
Product
Performance Board
-
The role of the performance board is accurate transmission of tester signals all the way to the device leads. Custom performance boards from ADVANTEST deliver support for DUTs (devices under test), as they become faster and smaller, with greater pin counts, and increasingly take the form of SMDs. ADVANTEST performance boards also support a host of test requirements, such as analog test, high-speed performance, and high-density, for testing state-of-the-art ICs.
-
Product
19" Enclosures for 6U VME VPX Boards
R4U8S
-
The R4U8S is a 4U height 19'' Rack Mount Industrial Chassis featuring 8 slots of either VME or cPCI 6U size boards. The R4U8S has successfully passed the mechanical, thermal, electromagnetic EMC/EMI qualification tests required by our customers. Its modular design enables to fulfil the requirements of application areas ranging from the environmentally benign right through to deployed industrial, airborne and naval applications.
-
Product
PCI Digital I/O Boards
PIO-D48U
-
Universal PCI OPTO-22 Compatible Board with 48 Digital I/O channels. Comes with SDK and Demo Programs. Includes one D-Sub Connector and one 50-pin flat cable header. Supports operating temperatures of 0 ~ 60 °C (32F ~ 140F). Replacement unit for DIO-48.
