Accelerometers
convert acceleration into electrical signals, usually denoted as a
See Also: Gyros, Gravimeters, IMU, Gyroscopes
-
Product
Fortis
-
A strong motion accelerometer with compact design for fast installation in any environment.
-
Product
IEPE Triaxial Accelerometer – 1000 mV/g
HDWBV-100
-
IEPE tri-axial accelerometer for the measurement of vibration transmitted to whole body.
-
Product
SparkFun Triple Axis Digital Accelerometer Breakout
ADXL313 (Qwiic)
-
The SparkFun ADXL313 Breakout is a low power, high resolution (up to 13-bits) 3-axis accelerometer for measurement up to ±4g. This breakout measures the static acceleration of gravity in tilt-sensing applications, as well as dynamic acceleration resulting from motion or shock. Digital output data is formatted as 16-bit two's complement and is accessible through the on-board Qwiic connectors (I2C) or SPI.
-
Product
Vibration Analyzers
-
A vibration analyzer measures and assesses the machinery condition using vibration sensors such as accelerometers, displacement probes, and velocity pickups.
-
Product
Biaxial Inclinometers
-
Columbia Research Laboratories
Columbia's Biaxial Inclinometers use the same force balance accelerometer technology used in our single axis inclinometers. These Biaxial Inclinometers are used in applications where dual axis tilt measurements are required. The SI-702B series is intended for use in applications such as platform stabilization, surface mapping and measuring tilt angles in remote locations. The SI-701AI series, is designed with an output circuit configuration made for use in 4-20mA data transmission systems.
-
Product
Portable Data Acquisition & Analysis System
LapCAT III
-
# 4, 8, or 16 channels# 1 MHz aggregate 12 bit sampling. Resolution is 0.024% of full scale# 13 recording durations, user selected: 132 msec to 1320 sec# Digital Triggering from any channel, with +/- slope or window# 6 full scale gain ranges, user selected: 0.4, 1, 2, 4, 10, and 20 volts full scale - with a 10mV/g accelerometer these equal 40g, 100g, 200g, 400g 1000g and 2000g full scale - higher or lower ranges by different sensor selection
-
Product
MEMS Module
-
The design and modeling of microelectromechanical systems (MEMS) is a unique engineering discipline. At small length scales, the design of resonators, gyroscopes, accelerometers, and actuators must consider the effects of several physical phenomena in their operation. Consequently, COMSOL Multiphysics is ideally suited for MEMS applications.
-
Product
Damped MEMS High-G Shock Accelerometers
-
Damped MEMS high-amplitude shock accelerometers represent state-of-the-art industry technology for miniature, high amplitude, DC response acceleration sensors. This series is capable of measuring long duration transient motion, as well as responding to and surviving extremely fast rise times, typical of a high-g shock event as found in explosive, gun and impact testing. Both packaged and OEM configurations are offered, to fulfill a variety of installation requirements.
-
Product
General Purpose Vibration Sensors
AC104
-
Multi-Purpose Accelerometer, Side Exit Connector / Cable, 100 mV/g.
-
Product
Accelerometer & Platform Test Bench
mS 1115
-
Platform Test Bench used to test the Digital Inputs, Accelerometer Count Reading, High and Low Gyro Torque control of Platform. It also performs Real Time Test for single negative pulse, checks Roll Axis, Pitch Axis, Azimuth Axis. Software package is available to test the Accelerometer.
-
Product
Multi Channel Linear Vibration Motor Aging Tester
BK8018
-
The BK8018B is our biggest Aging Tester for linear vibration motors. Connect up to 20 DUT's and the system will automatically test them all simultaneously. As well as evaluating current, it can also connect to accelerometers to test vibration characteristics. You can see information on the monitor in real time, and also store it to analyze later so you can keep track of the accuracy and stability of your manufacturing process. In addition, we will modify BaKo’s BS1123-BS8018 program to fit your needs so that the testing you do is a custom fit.
-
Product
LoRaWAN Wireless Vibration Sensor
WISE-2410
-
LoRaWAN wireless connectivityBuilt-in 3-axis accelerometer and temperature sensorComputing total 8 vibration characteristic values on boardCompliant with ISO 10816IP66 with battery-powered, no wiring installation neededEasy setting with user friendly interfaces on WISE StudioSupport wide temperature -20 ~ 80 °CRED Compliance
-
Product
PCI-4461, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 2-Input/2-Output Sound and Vibration Device
779307-01
-
The PCI‑4461 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous two-channel dynamic signal generation and simultaneous two-channel dynamic signal acquisition with six gain settings to configure the input range. The PCI‑4461 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
Product
Accelerometor, Gyro, Magnetometer Breakout Board
SEN-38001
-
The LSM9DS1 is a highly configurable, flexible and precise motion sensing solution from ST Microelectronics - the latest in a wide-ranging inertial product line. It integrates a 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer into a single IC , giving you a full nine degrees of freedom (9-DOF) in a tiny 3mm x 3.5mm package. Even with support components, square mounting pattern and connection breakouts for both SPI and I2C, this board is barely the size of a quarter.
-
Product
Vibration Sensors
-
Metra Meß- und Frequenztechnik Radebeul GmbH & Co. KG
Metra has been developing and manufacturing piezoelectric vibration sensors Since 1954. There are transducers for nearly every purpose. Our product range includes accelerometers with charge and IEPE compatible output.
-
Product
NI-9232, 3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
784397-01
-
3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9232 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9232 is also compatible with smart TEDS sensors. The NI‑9232 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
Product
Endevco Cryogenic Charge Output Accelerometers
-
PCB's acquisition of Endevco's full line of testing sensors means all Endevco sensors are now backed by PCB's Total Customer Satisfaction (TCS) guarantee. Endevco® cryogenic piezoelectric accelerometers are built specifically for measuring vibration under cryogenic conditions down to -452° F (-269° C). Signal outputs of these units are very stable even at extremely low temperatures. Their rugged internal construction is designed to withstand multiple cycles of thermal shock with steep temperature gradient. The accelerometers are self-generating devices that require no external power source for operation and contain no electronics. This allows them to operate below the -320° F (-196° C) limit of ICP accelerometers, down to -452° F (-269° C).
-
Product
Laser Vibrometer
-
Trialon’s state of the art laser vibrometer can produce vibration testing data without monitoring equipment attached to the test component. This application is used in sensitive situations where the use of more standard accelerometers cannot be used.
-
Product
Airborne Gravimeter
GT-2A
-
The very large dynamic range provides high precision data even in turbulent flying conditions; data is acquired through short periods of saturation in extreme turbulence by the automatic application of a reduced order Kalman filter, enabling platform misalignment to be computed and hence controlled; the automatic calibration program computes accelerometer scale factors and errors in perpendicularity between the accelerometer sensitive axis and the platform surface. The GT-2A installation in a fixed wing aircraft is shown in Fig 1 (courtesy of Excalibur).
-
Product
Inertial Measurement Units
IMU
-
Analog Devices inertial measurement unit (IMU) sensors are based on multiaxis combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors. Our technology reliably senses and processes multiple degrees of freedom, even in highly complex applications and under dynamic conditions. These plug and play solutions include full factory calibration, embedded compensation and sensor processing, and a simple programmable interface.
-
Product
General Inclinometers
-
Columbia Research Laboratories
Columbia's SI-701 Series of Inclinometers are electronic tilt sensors based on Force Balance Accelerometer technology. They produce high level low impedance output proportional to the sine of the tilt angle. Model SI-701B is a low cost general purpose sensor that can be up-graded with the addition of the Columbia "HP" torquer system (SI-701BI) for greater accuracy and ruggedness. A bi-axial version of both units (SI-702B) is also available. The Model SI-701BI is designed with an output circuit made for 4-20mA data transmission systems for industrial applications. The model SI-701FND is a fluid dampened premium performance inclinometer designed to produce accurate tilt data in extreme shock and vibration environments. The latest addition in the line is Model SI-701WPBI, a waterproof (to 150 feet) inclinometer which operates from a +15 volt supply with 4-20mA output. A single power supply powers both the sensor and the 4-20mA line driver.
-
Product
Gravimeter
-
Gravimeters are specialized accelerometers used to measure local gravity or variations in the gravitational field of the Earth. High-performance gravimeters and gravity gradiometers are well-suited for applications such as geophysical and geodetic surveying, precision navigation, exploration for natural resources, and underground fluid monitoring. Such sensors may also be useful for identifying special nuclear materials, treaty verification, and void detection.
-
Product
Compact Accelerometer (Shock Meter)
AP2019
-
Can be used as shock sensors in equipment diagnostic systems; Combination of high axial sensibility, intrinsic frequency and shock resistance; Low sensitivity to electromagnetic fields; Low intrinsic noise level.
-
Product
Wireless Vibration Sensors
-
A Wireless Vibration Sensor is a device that includes an Accelerometer and is capable of measuring vibration and send it to a receiver using a Wireless protocol. Depending on the wireless protocol used, some of these sensors may even transmit data in real time. Hence having the capability to connect via peer to peer or mesh network.
-
Product
Signal Conditioners
General Purpose
-
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
Product
Accelerometer
-
EMIC offers many kinds of accelerometers available for various vibration measurements. They are a ultra small light weight accelerometer for highly precise measurement, a special tri-axial accelerometer for simultaneously measuring a vibration in three orthogonal axes, a large output accelerometer for measuring an earthquake and a suitable accelerometer for measuring and analyzing a building structure.
-
Product
High Sensitivity ICP® Accelerometers
-
High sensitivity ICP® accelerometers are specifically designed to enable the detection of ultra-low-level, low-frequency vibrations associated with very large structures, foundations, and earth tremors. These sensors typically possess exceptional measurement resolution as the result of its comparatively larger size, which furnishes a stronger output signal and a lower noise floor. All units are hermetically sealed in a titanium or stainless steel housing. Models that include a 2-pin, military style connector provide the added benefit of being electrically case isolated for superior RF and EMI protection.
-
Product
Programmable Sensor Module With CAN Connection
PCAN GPS
-
The PCAN-GPS is a freely programmable sensor module for position and attitude determination. It has a satellite receiver, a magnetic field sensor, an accelerometer and a gyroscope. The recorded data can be transmitted on a CAN bus and logged on the internal memory card. The data is processed by a microcontroller from the NXP LPC4000 series.
-
Product
Piezo-resistive Accelerometer
-
A Piezo-resistive Accelerometer has a stable structure composed on a silicon chip created by the micromachining and semiconductor production technology. A mass and a beam on which a set of the Piezo-resisters are created on the silicon chip. A set of electrical bridged is formed by such Piezo-resistive resisters to generate signals proportional to the applied acceleration.
-
Product
NI-9230, 3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
784396-01
-
3-Channel, 12.8 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9230 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9230 is also compatible with smart TEDS sensors. The NI‑9230 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
