Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
Product
Waveguide Amplifiers
-
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
Product
Rotary Joint
-
RF Lambda’s rotary joints are available in a variety of channels and configurations allowing the connection of waveguides and allowing for rotation of the different sections.
-
Product
Broadband Detectors
-
These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.
-
Product
Double Ridged Waveguide Horn
QRH40
-
Frequency range: 4 GHz - 40 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xK female Power (CW / Peak): 10W / 20 W
-
Product
Frequency Converters
-
Ducommun's frequency converter families include waveguide detectors (FAS), passive and active multipliers (FMP and FMA), up and down converters (FUB and FDB), harmonic mixers (FDH), subharmonically pumped up and down converters (FUS and FDS) and phase detectors and single sideband modulators (FPB and FSS). These devices are offered in 7 waveguide bands to cover entire 18 to 110 GHz frequency spectrum. These converters employ high performance GaAs Schottky beamlead diodes and DLT's proprietary circuit configuration to produce superior performance, such as low conversion loss and up to full waveguide instantaneous operation bandwidth.
-
-
Product
Magic Tee
MHTXE
-
The MHTXE Magic Tee Hybrid Couplers for millimeter waves are matched power dividers for variety of applications (general purpose power splitters, power combiners, phase measurement circuits, phase / frequency discriminators). The MHTXE Magic Tee Hybrid Couplers are available in waveguide bands between 33 and 170 GHz. These couplers are four-port transmission line components with a port configuration as shown in figure. Operation bandwidth is limited to 20÷90% waveguide operation frequency range depending on performance specifications.
-
Product
Waveguide and Coaxial Rotary Joint Assembly
-
Waveguide and Coaxial Rotary Joints are used for the transmission of power and signal between the locked and rotating parts of a radar or satcom system.
-
Product
Integrated Couplers/ Harmonic Mixers
-
These waveguide bandwidth integrated coupler/mixers are designed to allow phase locking or signal monitoring of compact millimeter wave systems. RF inputs and outputs are on opposite sides of a thin wafer to obtain minimum insertion length. These devices use silicon Schottky barrier beam-lead diodes on a rugged stripline circuit. Nominal coupling value is 10 dB. For coupling values greater than 10 dB, non-directional coupler models are available (consult factory).
-
Product
Waveguide Accessories
-
Designed with our leading waveguide development expertise and application knowledge, CAES Waveguide accessories are offered in a variety of options, sizing and materials.
-
Product
PD-200 High-Speed High-Power Photodetector
-
These high speed photodiode, PD-200, is hermetically sealed, high reliability, low harmonic distortion photodiode modules designed for high optical power applications with minimum bandwidths of 20 GHz. The device is well suited for receiver applications with optical pre-amplification, and is available either with or without an internal 50Ω termination. The photodiode module is available in either a V-connector package or a miniature surface mount package with CPW (coplanar waveguide) RF output.
-
Product
Double Ridged Waveguide Horn
DRH203
-
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
Product
Waveguide Duplexer
-
Waveguide Duplexers supporting commercial communication to combine transmit and receive on to one antenna
-
Product
Waveguide Adapter
-
RF Lambda’s waveguide adapter product line is used to convert a waveguide interface to a coaxial interface. They come in a variety of frequencies, connector options and materials. They offer low insertion loss and VSWR as well as high power handling.
-
Product
Waveguide Power Sensor
V8486A
Power Sensor
The V8486A waveguide power sensor measures average power over the frequency range 50 GHz to 75 GHz and power range -30 to +20 dBm.
-
Product
Waveguide Switches
-
With over 70 years of RF experience, EVERAXIS specializes in designing the most demanding Waveguide Switches in extremely complex systems, including in low quantities.
-
Product
Double Ridged Waveguide Horn
DRH50
-
Frequency range: 4.5 GHz - 50 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: 2.40mm female Power (CW / Peak): 10 W / 20 W
-
Product
Waveguide Power Meters
-
Start Frequency (MHz)2400Stop Frequency (MHz)2500Power (Watts CW)5000ConnectorsTBR
-
Product
Mechanical Calibration Kit, 18 To 26.5 GHz, Waveguide, WR-42
K11644A
Mechanical Calibration Kit
The Keysight K11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the Thru-Reflect-Line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 75 to 110 GHz
W281D
Coax Adapter
The Keysight W281D is a 1-mm male to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281D is used with the Keysight 8510XF systems.
-
Product
Double Ridged Waveguide Horn
QRH400
-
Frequency range: 400 MHz - 6 GHz VSWR (max): < 2.3 :1Impedance: 50 O (Ohm)Connector: 2xN female Power (CW / Peak): 350 W / 350 W
-
Product
Microwave Testing
170
-
The PICOPROBE® MODEL 170, a high performance microwave probe which incorporates a WR-6 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
Product
Multi-channel Optical Power Meter For Swept Test System
MPM-210HMPM-211, 212, 213, 215
-
Our MPM-210H is ideal for IL, WDL and PDL measurement of multi-port optical components including Dense Wavelength Division Multiplexing (DWDM), Arrayed Waveguide Gratings（AWG) , Wavelength Selective Switches (WSS) and more. When combined with our TSL-Series laser equipped with a power monitor output, the MPM-210H allows the user to complete real-time high precision IL measurements.
-
Product
Signal Generator Extension Modules
SGX
-
Virginia Diodes, Inc. (VDI) Signal Generator Extension (SGX) modules provide high performance frequency extension of microwave signal generators into the THz range. VDI SGX modules offer full waveguide band coverage and are available from WR15 (50 to 75 GHz) to WR1.0 (750 to 1100 GHz) with additional bands under development. This turn-key, sweepable solution is compatible with any microwave signal generator that meets the input frequency and power requirements.
-
Product
Microwave Wideband PIN-TIA Receivers
MR22 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR22 series microwave wideband optical receiver, adopts High linear PIN diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
-
-
Product
Near Field Probes
-
Anteral has extensive background in the design of Near Field Probes (open ended waveguides probes). Our Near Field Probes are currently being used in several laboratories around the world including the ESA's anechoic chamber. Anteral designs Near Field Probes from 10 GHz to 750 GHz covering the sectors requirements. Moreover, our Near Field Probes have a sharped design minimize reflections.
-
Product
Waveguide Bends
-
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
