Adapters
Interfaces that facilitate interconnect between two dissimilar elements.
-
Product
VXI Adapter Plate, Plug and Play, 2 Tier, 14U, for 9050 VXI Receiver
310113364
Adapter Plate
The VXI Plug & Play Plate allows the 9050 VXI receiver to be mounted to a chassis with the Plug & Play Flange Kit from the chassis manufacturer.
-
Product
Universal SOIC-to-0.600 [15.24] DIP Adaptor
Series 647
-
Universal SOIC to .600 [15.24] DIP Adapter. 44 pin adapter for mounting Aries Series 547 Universal SOIC ZIF (zero insertion force) Test Socket to .600 [15.24] DIP PCB layout. Consult Data Sheet No. 10015 for test socket information.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 1.5m
N1425A
Coaxial Cable
The N1425A is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425A is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425A enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425A to the B2985B/87B.
-
-
Product
Protocol Control Control
PC2
-
The PC2 software from SCSI Toolbox, LLC brings a new level of parallel SCSI protocol control to your test environment. Designed in cooperation with LSI Logic to work with their Fusion-MPT Message Passing Interface technology, PC2 allows all negotiated parameters to be displayed or set for all devices connected to any SCSI Host Bus Adapter based on the LSI53C1030 chip set. PC2 also provides the means to generate hardware SCSI bus resets.
-
Product
Mini DisplayPort to VGA Adapter, 0.5 m (0 to 70 degree Celsius)
157230-0R5
-
Mini DisplayPort to VGA Adapter, 0.5 m (0 to 70 degree Celsius)
-
Product
PLCC-to-DIP Adaptor
Series 652000/653000
-
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Ideal for prototyping and testing/evaluation. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 40 to 60 GHz
U281B
-
The Keysight U281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
PCIe Gen 4.0 RAID Adapter
MegaRAID 9560-8i
-
The MegaRAID 9500 series is the industry’s first PCIe Gen 4.0 RAID adapter family, offering PCIe Gen 4.0 host and storage interfaces. The MegaRAID 9560-8i adapter, based on the SAS3908 high-port count PCIe 4.0 x8 RAID-on-Chip (RoC), delivers twice the performance of previous generations.
-
-
Product
PCI Express-to-XMC Adapter
4876
-
The Technobox, Inc. P/N 4876 PCI Express-to-XMC Adapter is a development/diagnostics tool that permits the testing of a PCIe card in an XMC site. Up to 8 lanes are supported via the P15 connector. Several activity LEDs located at the edge of the board give an indication of key XMC and PCI Express signals and voltages.
-
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
CEI-4x10GBASE-T
Network Interface Controller
- Support up to four 10GbE copper interfaces (10GBASE-T)- COM.0 R3.1 Type 7 compliant- Dedicated for Express-ID7
-
Product
Test Leads Adapter Sets
-
A physical device used to connect electronic test equipment to a device under test.
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
-
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
USB CAN Interface Adapter
COMMDongle
-
Designed for use with VISUALCONNX and other third-party software, COMMDongle products initially support one or more CAN communications buses.
-
Product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
-
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
Product
Adapter, APC-7 to SMA (m)
11533A
Contact Adapter (ITA)
The Keysight 11533A is a general purpose grade, APC-7 to SMA male adapter.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, For NI PXI-6509
510140138-1
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, for NI PXI-6509
-
-
Product
NM-SM 50 N-Male to SMA-Male Adapter
-
NM-SM 50 Adapter, N-Male to SMA-Male, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
Product
Adapter
ZET 430
-
*Aligns sensor output signal with the FFT spectrum analyzer input;*Sends the FFT spectrum analyzer generator signal to the sensor calibration input;*Provides power supply to the sensor from the integrated ±12 V power supply unit.
-
Product
POWERSTROKE FUEL INJECTOR TEST KIT
DFST20
-
*Tests Powerstroke engines from 1994 to current*Includes adapters necessary to pressure test the fuel system*Adapters can be used for testing at both the fuel filter and at the fuel pump
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz
Q281B
-
The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Test Adapter
PMC-UNIV-TEST
-
PCI adapter for PMC with options for PCI and PMC Stack Pass through connections
-
Product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-01
Digitizer
The NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Test Port Adapter Set, 1.85 Mm To 1.85 Mm
85130H
-
The Keysight 85130H test port adapter protects the test set port from being directly connected to the device under test. This adapter has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a 1.85 mm to 1.85 mm male adapter and a 1.85 mm to 1.85 mm female adapter. The frequency range for these adapters is dc to 67 GHz with a return loss of 23 dB or better.
-
Product
VPC Receiver Frame
ABex REC21-84TE-EXT
-
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
Product
20V Battery Internal Resistance/Voltage Tester
TOB-BVIR
-
Xiamen Tob New Energy Technology Co., Ltd
Portable Internal Resistance Tester for All Batteries 0 - 20V With Charging Adapter. TOB-BVIR Battery internal resistance tester can be used for measuring the Internal Resistance and Open CircuitVoltage of almost all of the commercial batteries such as Secondary battery, Lead acid battery, Nickle cadmium, Nickle-metal Hydride and Li-ion battery.
-
Product
Adapter/Stainless Steel
WADP-29M29M
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
