Fixtures
orient and afix UUT.
See Also: Fixturing, Test Fixtures, Mechanical Fixtures, Vacuum Fixtures, Jigs
-
product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2-228X (Small IF) / 230540
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester.
-
product
Clamshell Type Mechanical Fixtures
Series 11
The MT Series 11 dual well mechanical kits are an affordable solution to printed circuit board testing with the advantage of testing two devices. These can be similar devices, or devices that are used together in a functional test. The Series 11 Kits have the same available features and options as the Series 10 Kits.
-
product
Magnetizing Fixtures
Usually, the magnetizing fixture (coil) is specifically designed for the task of the customer and the product.In the simplest case, only the necessary parameters for the dimensions of the component are calculated for an axial coil, and the device can be designed and manufactured according to standard procedures.
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
Clamshell Type Mechanical Fixtures
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
product
Vacuum Test Fixtures
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
product
Through Connector Functional Test Fixtures
Circuit Check is a pioneer in the development and implementation of access mechanisms enabling testing of circuits through on-board connectors.
-
product
PCB Test Fixture Kits And Customized Fixtures
Mirotech manufactures portable benchtop PCB test fixture kits and provides customized test fixture solutions for the electronics industry. Our innovative, streamlined designs are compact in size and feature a linear collapsing system, interchangeable and reusable plate design, top and bottom probing, and are affordably priced. All fixtures are built using high quality hardware and materials and manufactured using the DATRON M8Cube, known for its precision and accuracy. Each of our custom designs are unique to our customer’s particular project requirements. Fixture kits come pre-assembled, and include blank plates ready for you to drill your test pattern.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Food Grips and Fixtures
AMETEK Sensors, Test & Calibration
We supply material testing instruments to some of the world’s most innovative companies within the food industry. The reason for this is our extensive experience within food testing, combined with our high precision texture analysis and packaging test systems.
-
product
In-Circuit Test Fixtures
Every type of in-circuit test fixtures (wired, wireless, pneumatic, vacuum) for all major tester brands.
-
product
In-Line Functional Test Fixtures
Add an advantage to in-line production with fast change over interchangeable fixturing. Circuit Check’s in-line board handlers and in-line board handler fixturing exceed the high performance requirements associated with high-volume production. Circuit Check supports in-line fixturing for all the leading handlers.
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
Automatic Fixture Removal
S95007B
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
product
Accessories For Instruments And Fixtures
N1254A
The N1254A includes several optional accessories and adapters for instruments.
-
product
Custom Designed Test Fixtures
We specialize in automated test systems for both RF and digital devices, modules and systems. Please call to discuss your test requirements.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
product
Shielding Effectiveness
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
product
DC Bias and RF Stimulus Control Module
Quantum SMART Fixture
Accel-RF Corporation, the world leader in turnkey RF automated reliability test instruments, has "unplugged" the industry-leading RF SMART Fixture from their automated test platform and made it available for benchtop test. The NEW Quantum SMART Fixture is a programmable self-contained DC bias and RF stimulus control module capable of synchronizing sequenced independent pulsed-bias and pulsed-RF signals to a DUT or remote fixture. The signals are controlled from a user interface compatible with Accel-RF's LIFETEST software. The Quantum SMART fixture is capable of "active" temperature control and monitoring of a remote DUT through embedded firmware in the microprocessor
-
product
Thermomechanical Analyzer
TMA 450
TA Instruments invites you to experience the finest in Thermomechanical Analyzers, the Discovery TMA 450. Discover the advanced engineering and attention to detail that provides enhancements in every aspect of performance and a new level of user experience. Featuring advanced testing capabilities and the widest range of fixtures, the Discovery TMA 450 is sure to meet and exceed your expectations. It’s never been easier to get great TMA data!
-
product
Freezing Tester
Our Freezing Tester units are available in vertical or horizontal configurations are used to test the bending/flexing durability of rubber, plastics, synthetic leather, shoes, etc., under cold temperatures as low as -30°C or -70°C depending on the selected model. The test chambers can be equipped with a variety of flexing/bending fixtures made of stainless steel. These models conform to ASTM D 1790, and ASTM D1593 standards.
-
product
PXI 22-Channel 2A Fault Insert Switches
40-202-001
This is the 22 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test.
-
product
Drop-In Functional Test Fixtures
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
product
PXI Expandable 16x16 RF Matrix 50Ohm SMB
45-720A-511
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
product
9050 Rack Mount
The rack mountable 9050 50 Module Receiver is designed to accept 9025 and 9050 ITAs and is ideal for systems with advanced mass interconnect requirements. The 9050 can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed for creating custom interfaces ideal for functional and system testing applications.
-
product
Non-Linear Junction Detector
ORION™ HGO-4000
The ORION HGO-4000 is REI’s original high gain Non-Linear Junction Detector for special applications. The ORION HGO-4000 can locate listening devices and semiconductors in walls floors, ceilings, fixtures, furniture or containers and provides a user the capability to detect hidden electronic devices, regardless of whether the device is radiating, hard wired, or even turned off.
-
product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
product
Stand-Alone Test Fixture
MA 2012/D/H
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 15,50 kg
-
product
DGS-65 Test Panel with FV Simulator / Bed of Nails
TA-650
The TA-650 is a new test fixture that will give any instrument shop the ability to conduct more detailed testing of the Collins DGS-65 directional gyro then was previously available.
